[ 0.656331] i2c_dev: i2c /dev entries driver [ 0.798080] device-mapper: uevent: version 1.0.3 [ 0.798129] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: XXX@XXX [ 0.829918] raid6: avx2x4 gen() 18703 MB/s [ 0.846937] raid6: avx2x4 xor() 10303 MB/s [ 0.863919] raid6: avx2x2 gen() 18493 MB/s [ 0.880931] raid6: avx2x2 xor() 11255 MB/s [ 0.897923] raid6: avx2x1 gen() 16867 MB/s [ 0.914920] raid6: avx2x1 xor() 9533 MB/s [ 0.931922] raid6: sse2x4 gen() 10001 MB/s [ 0.948924] raid6: sse2x4 xor() 5992 MB/s [ 0.965919] raid6: sse2x2 gen() 10192 MB/s [ 0.982920] raid6: sse2x2 xor() 6104 MB/s [ 0.999925] raid6: sse2x1 gen() 8513 MB/s [ 1.016922] raid6: sse2x1 xor() 5164 MB/s [ 1.016924] raid6: using algorithm avx2x4 gen() 18703 MB/s [ 1.016925] raid6: .... xor() 10303 MB/s, rmw enabled [ 1.016926] raid6: using avx2x2 recovery algorithm [ 1.018107] xor: automatically using best checksumming function avx [ 1.069514] Btrfs loaded, crc32c=crc32c-intel, zoned=yes, fsverity=no [ 1.082241] ACPI: bus type USB registered [ 1.082261] usbcore: registered new interface driver usbfs [ 1.082268] usbcore: registered new interface driver hub [ 1.082278] usbcore: registered new device driver usb [ 1.084804] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.210926] tsc: Refined TSC clocksource calibration: 3591.667 MHz [ 1.210933] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x33c5939df6d, max_idle_ns: 440795297647 ns [ 1.210947] clocksource: Switched to clocksource tsc [ 1.244742] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2 [ 1.248899] ACPI: button: Power Button [PWRB] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 1.252034] ACPI: button: Power Button [PWRF] ehci-pci: EHCI PCI platform driver [ 1.266485] ehci-pci 0000:00:1a.0: EHCI Host Controller [ 1.266492] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 1.266508] ehci-pci 0000:00:1a.0: debug port 2 [ 1.267226] Linux agpgart interface v0.103 [ 1.270433] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7c3c000 [ 1.278272] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 1.278308] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16 [ 1.278311] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 1.278313] usb usb1: Product: EHCI Host Controller [ 1.278314] usb usb1: Manufacturer: Linux 5.16.13-desktop-1omv4003 ehci_hcd [ 1.278315] usb usb1: SerialNumber: ... [ 1.278427] hub 1-0:1.0: USB hub found [ 1.278436] hub 1-0:1.0: 3 ports detected [ 1.278903] ehci-pci 0000:00:1d.0: EHCI Host Controller [ 1.278909] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 1.278935] ehci-pci 0000:00:1d.0: debug port 2 [ 1.282852] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7c3b000 [ 1.284476] cryptd: max_cpu_qlen set to 1000 [ 1.286801] ACPI: bus type drm_connector registered [ 1.290828] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 1.290871] AVX2 version of gcm_enc/dec engaged. [ 1.290904] AES CTR mode by8 optimization enabled [ 1.297362] SCSI subsystem initialized [ 1.298144] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16 [ 1.298148] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 1.298150] usb usb2: Product: EHCI Host Controller [ 1.298152] usb usb2: Manufacturer: Linux 5.16.13-desktop-1omv4003 ehci_hcd [ 1.298153] usb usb2: SerialNumber: ... [ 1.306140] hub 2-0:1.0: USB hub found [ 1.306168] hub 2-0:1.0: 3 ports detected [ 1.307928] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 1.307934] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 [ 1.309012] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810 [ 1.309164] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16 [ 1.309166] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 1.309168] usb usb3: Product: xHCI Host Controller [ 1.309169] usb usb3: Manufacturer: Linux 5.16.13-desktop-1omv4003 xhci-hcd [ 1.309170] usb usb3: SerialNumber: ... [ 1.309210] libata version 3.00 loaded. [ 1.313833] hub 3-0:1.0: USB hub found [ 1.313856] hub 3-0:1.0: 14 ports detected [ 1.316461] ahci 0000:00:1f.2: version 3.0 [ 1.317660] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 1.317664] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 [ 1.317667] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed [ 1.317706] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.16 [ 1.317708] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 1.317710] usb usb4: Product: xHCI Host Controller [ 1.317711] usb usb4: Manufacturer: Linux 5.16.13-desktop-1omv4003 xhci-hcd [ 1.317712] usb usb4: SerialNumber: ... [ 1.317714] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x7 impl SATA mode [ 1.317718] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst [ 1.317858] hub 4-0:1.0: USB hub found [ 1.317875] hub 4-0:1.0: 6 ports detected [ 1.318424] usb: port power management may be unreliable [ 1.325309] scsi host0: ahci [ 1.325583] scsi host1: ahci [ 1.325679] scsi host2: ahci [ 1.325776] scsi host3: ahci [ 1.325877] scsi host4: ahci [ 1.326584] scsi host5: ahci [ 1.326626] ata1: SATA max UDMA/133 abar m2048@0xf7c3a000 port 0xf7c3a100 irq 26 [ 1.326630] ata2: SATA max UDMA/133 abar m2048@0xf7c3a000 port 0xf7c3a180 irq 26 [ 1.326633] ata3: SATA max UDMA/133 abar m2048@0xf7c3a000 port 0xf7c3a200 irq 26 [ 1.326634] ata4: DUMMY [ 1.326635] ata5: DUMMY [ 1.326636] ata6: DUMMY [ 1.410823] i915 0000:00:02.0: vgaarb: deactivate vga console [ 1.416596] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 1.439382] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 [ 1.440048] ACPI: video: [Firmware Bug]: Duplicate ACPI video bus devices for the same VGA controller, please try module parameter "video.allow_duplicates=1"if the current driver doesn't work. [ 1.467311] fbcon: i915drmfb (fb0) is primary device [ 1.516920] usb 1-1: new high-speed USB device number 2 using ehci-pci [ 1.548922] usb 2-1: new high-speed USB device number 2 using ehci-pci [ 1.552249] Console: switching to colour frame buffer device 160x64 [ 1.556921] usb 3-5: new full-speed USB device number 2 using xhci_hcd [ 1.571961] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device [ 1.632042] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 1.632059] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.632074] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 1.632200] ata1.00: ATA-11: Emtec X150 480GB, V3.0.8, max UDMA/133 [ 1.632225] ata1.00: 937703088 sectors, multi 1: LBA48 NCQ (depth 32), AA [ 1.632495] ata1.00: configured for UDMA/133 [ 1.632581] scsi 0:0:0:0: Direct-Access ATA Emtec X150 480GB .8 PQ: 0 ANSI: 5 [ 1.632599] ata2.00: ATA-9: WDC WD10EZEX-60M2NA0, 03.01A03, max UDMA/100 [ 1.633161] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 1.634031] ata3.00: ATAPI: TSSTcorp CDDVDW TS-L633F, TF01, max UDMA/100 [ 1.634248] ata2.00: configured for UDMA/100 [ 1.634309] scsi 1:0:0:0: Direct-Access ATA WDC WD10EZEX-60M 1A03 PQ: 0 ANSI: 5 [ 1.636250] ata3.00: configured for UDMA/100 [ 1.637281] scsi 2:0:0:0: CD-ROM TSSTcorp CDDVDW TS-L633F TF01 PQ: 0 ANSI: 5 [ 1.645230] usb 1-1: New USB device found, idVendor=8087, idProduct=8008, bcdDevice= 0.04 [ 1.645232] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=... [ 1.645373] hub 1-1:1.0: USB hub found [ 1.645479] hub 1-1:1.0: 6 ports detected [ 1.667968] sd 0:0:0:0: [sda] 937703088 512-byte logical blocks: (480 GB/447 GiB) [ 1.667978] sd 0:0:0:0: [sda] Write Protect is off [ 1.667980] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.667989] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.668120] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 1.668122] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 1.668127] sd 1:0:0:0: [sdb] Write Protect is off [ 1.668129] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1.668138] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.677172] sda: sda1 sda2 [ 1.679230] usb 2-1: New USB device found, idVendor=8087, idProduct=8000, bcdDevice= 0.04 [ 1.679234] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=... [ 1.679384] hub 2-1:1.0: USB hub found [ 1.679480] hub 2-1:1.0: 8 ports detected [ 1.680976] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.684889] usb 3-5: New USB device found, idVendor=1ea7, idProduct=0064, bcdDevice= 2.00 [ 1.684892] usb 3-5: New USB device strings: Mfr=0, Product=1, SerialNumber=... [ 1.684894] usb 3-5: Product: 2.4G Mouse [ 1.690532] hid: raw HID events driver (C) Jiri Kosina [ 1.734867] sdb: sdb1 sdb2 [ 1.745981] sd 1:0:0:0: [sdb] Attached SCSI disk [ 1.751453] usbcore: registered new interface driver usbhid [ 1.751455] usbhid: USB HID core driver [ 1.754073] input: 2.4G Mouse as /devices/pci0000:00/0000:00:14.0/usb3/3-5/3-5:1.0/0003:1EA7:0064.0001/input/input4 [ 1.754162] input: 2.4G Mouse as /devices/pci0000:00/0000:00:14.0/usb3/3-5/3-5:1.0/0003:1EA7:0064.0001/input/input5 [ 1.754240] hid-generic 0003:1EA7:0064.0001: input,hiddev0,hidraw0: USB HID v1.10 Mouse [2.4G Mouse] on usb-0000:00:14.0-5/input0 [ 1.771758] sr 2:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.771762] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.797824] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 1.798924] usb 3-11: new low-speed USB device number 3 using xhci_hcd [ 1.930080] usb 3-11: New USB device found, idVendor=0461, idProduct=0010, bcdDevice= 1.04 [ 1.930085] usb 3-11: New USB device strings: Mfr=1, Product=2, SerialNumber=... [ 1.930087] usb 3-11: Product: USB Keyboard [ 1.930089] usb 3-11: Manufacturer: NOVATEK [ 1.933835] input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:14.0/usb3/3-11/3-11:1.0/0003:0461:0010.0002/input/input6 [ 1.984979] hid-generic 0003:0461:0010.0002: input,hidraw1: USB HID v1.10 Keyboard [NOVATEK USB Keyboard] on usb-0000:00:14.0-11/input0 [ 1.988818] input: NOVATEK USB Keyboard System Control as /devices/pci0000:00/0000:00:14.0/usb3/3-11/3-11:1.1/0003:0461:0010.0003/input/input7 [ 2.039971] input: NOVATEK USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:14.0/usb3/3-11/3-11:1.1/0003:0461:0010.0003/input/input8 [ 2.040011] hid-generic 0003:0461:0010.0003: input,hidraw2: USB HID v1.10 Device [NOVATEK USB Keyboard] on usb-0000:00:14.0-11/input1 [ 2.316417] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. [ 8.577518] EXT4-fs (sdb2): re-mounted. Opts: (null). Quota mode: none. [ 8.719592] fuse: init (API version 7.35) [ 8.870949] vboxdrv: Found 8 processor cores [ 8.887150] vboxdrv: TSC mode is Invariant, tentative frequency 3591664876 Hz [ 8.887152] vboxdrv: Successfully loaded version 6.1.32 r149290 (interface 0x00320000) [ 9.106023] VBoxNetFlt: Successfully started. [ 9.203879] VBoxNetAdp: Successfully started. [ 10.105820] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 19.709873] e1000e: Intel(R) PRO/1000 Network Driver [ 19.709875] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 19.710034] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 19.735436] i801_smbus 0000:00:1f.3: SPD Write Disable is set [ 19.735461] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt [ 19.735883] i2c i2c-8: 4/4 memory slots populated (from DMI) [ 19.736173] i2c i2c-8: Successfully instantiated SPD at 0x50 [ 19.736452] i2c i2c-8: Successfully instantiated SPD at 0x51 [ 19.736739] i2c i2c-8: Successfully instantiated SPD at 0x52 [ 19.737030] i2c i2c-8: Successfully instantiated SPD at 0x53 [ 19.737164] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20210930/utaddress-204) [ 19.737169] ACPI: OSL: Resource conflict; ACPI support missing from driver? [ 19.737177] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x00000000000008FF (\GPR) (20210930/utaddress-204) [ 19.737180] ACPI: OSL: Resource conflict; ACPI support missing from driver? [ 19.737180] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000053F (\GPRL) (20210930/utaddress-204) [ 19.737183] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x00000000000008FF (\GPR) (20210930/utaddress-204) [ 19.737186] ACPI: OSL: Resource conflict; ACPI support missing from driver? [ 19.737186] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000053F (\GPRL) (20210930/utaddress-204) [ 19.737189] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x00000000000008FF (\GPR) (20210930/utaddress-204) [ 19.737192] ACPI: OSL: Resource conflict; ACPI support missing from driver? [ 19.737192] lpc_ich: Resource conflict(s) found affecting gpio_ich [ 19.769948] tpm_tis 00:0a: 1.2 TPM (device-id 0xB, rev-id 16) [ 19.782488] e1000e 0000:00:19.0 0000:00:19.0 (uninitialized): registered PHC clock [ 19.845831] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 253E0F38E1CC3FCAE2CD7FA4B7B8F1CB [ 19.845836] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection [ 19.845885] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF [ 19.853842] parport_pc 00:09: reported by Plug and Play ACPI [ 19.853955] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] thermal LNXTHERM:00: registered as thermal_zone0 [ 19.889462] ACPI: thermal: Thermal Zone [TZ00] (28 C) [ 19.889617] thermal LNXTHERM:01: registered as thermal_zone1 [ 19.889619] ACPI: thermal: Thermal Zone [TZ01] (30 C) [ 20.173986] snd_hda_intel 0000:00:03.0: enabling device (0100 -> 0102) [ 20.174090] snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) [ 20.174226] snd_hda_intel 0000:00:1b.0: enabling device (0100 -> 0102) [ 20.185344] input: HP WMI hotkeys as /devices/virtual/input/input10 [ 20.186563] input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input11 [ 20.186593] input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input12 [ 20.186621] input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input13 [ 20.186650] input: HDA Intel HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:03.0/sound/card0/input14 [ 20.186762] input: HDA Intel HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:03.0/sound/card0/input15 [ 20.210962] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer [ 20.210964] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules [ 20.210965] RAPL PMU: hw unit of domain package 2^-14 Joules [ 20.210966] RAPL PMU: hw unit of domain dram 2^-14 Joules [ 20.210967] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules [ 20.218235] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC221: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line [ 20.218238] snd_hda_codec_realtek hdaudioC1D0: speaker_outs=1 (0x17/0x0/0x0/0x0/0x0) [ 20.218240] snd_hda_codec_realtek hdaudioC1D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0) [ 20.218241] snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0 [ 20.218241] snd_hda_codec_realtek hdaudioC1D0: inputs: [ 20.218242] snd_hda_codec_realtek hdaudioC1D0: Mic=0x1a [ 20.218243] snd_hda_codec_realtek hdaudioC1D0: Line=0x1b [ 20.258828] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input16 [ 20.258856] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card1/input17 [ 20.258879] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card1/input18 [ 20.258907] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input19 [ 20.533651] zram0: detected capacity change from 0 to 16278528 [ 20.739659] iTCO_vendor_support: vendor-support=0 [ 20.797297] iTCO_wdt iTCO_wdt.1.auto: Found a Lynx Point TCO device (Version=2, TCOBASE=0x0460) [ 20.797317] at24 8-0050: supply vcc not found, using dummy regulator [ 20.797347] iTCO_wdt iTCO_wdt.1.auto: initialized. heartbeat=30 sec (nowayout=0) [ 20.797895] at24 8-0050: 256 byte spd EEPROM, read-only [ 20.797926] at24 8-0051: supply vcc not found, using dummy regulator [ 20.798484] at24 8-0051: 256 byte spd EEPROM, read-only [ 20.798500] at24 8-0052: supply vcc not found, using dummy regulator [ 20.799041] at24 8-0052: 256 byte spd EEPROM, read-only [ 20.799053] at24 8-0053: supply vcc not found, using dummy regulator [ 20.799581] at24 8-0053: 256 byte spd EEPROM, read-only [ 20.896754] intel_rapl_common: Found RAPL domain package [ 20.896756] intel_rapl_common: Found RAPL domain core [ 20.896757] intel_rapl_common: Found RAPL domain uncore [ 20.896758] intel_rapl_common: Found RAPL domain dram [ 20.896762] intel_rapl_common: RAPL package-0 domain package locked by BIOS [ 20.896766] intel_rapl_common: RAPL package-0 domain dram locked by BIOS [ 20.900314] ppdev: user-space parallel port driver [ 21.219637] e1000e 0000:00:19.0 eno1: renamed from eth0 [ 21.219774] intel-spi intel-spi: w25q128 (16384 Kbytes) [ 21.366148] Creating 1 MTD partitions on "intel-spi": [ 21.366151] 0x000000000000-0x000001000000 : "BIOS" [ 21.574681] Adding 8139260k swap on /dev/zram0. Priority:100 extents:1 across:8139260k SSDscFS [ 35.947461] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 36.852441] e1000e 0000:00:19.0 eno1: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 36.852480] IPv6: ADDRCONF(NETDEV_CHANGE): eno1: link becomes ready [ 41.482968] NET: Registered PF_PACKET protocol family [ 333.761025] zram0: detected capacity change from 16278528 to 0