Probe #6fabc91907 of Microsoft Surface Pro 4

Log: iw_list

Wiphy phy2 wiphy index: 2 max # scan SSIDs: 4 max scan IEs length: 2285 bytes max # sched scan SSIDs: 0 max # match sets: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports RSN-IBSS. Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP-128 (00-0f-ac:4) * CCMP-256 (00-0f-ac:10) * GCMP-128 (00-0f-ac:8) * GCMP-256 (00-0f-ac:9) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * monitor Band 1: Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps * 5.5 Mbps * 11.0 Mbps * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) * 2472 MHz [13] (20.0 dBm) * 2484 MHz [14] (disabled) Supported commands: * new_interface * set_interface * new_key * start_ap * new_station * new_mpath * set_mesh_config * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * frame * frame_wait_cancel * set_wiphy_netns * set_channel * probe_client * set_noack_map * register_beacons * start_p2p_device * set_mcast_rate * connect * disconnect * set_qos_map * set_multicast_to_unicast software interface modes (can always be added): * monitor interface combinations are not supported HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS. Device supports SAE with AUTHENTICATE command Device supports low priority scan. Device supports scan flush. Device supports AP scan. Device supports per-vif TX power setting Driver supports full state transitions for AP/GO clients Driver supports a userspace MPM Device supports configuring vdev MAC-addr on create. max # scan plans: 1 max scan plan interval: -1 max scan plan iterations: 0 Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0x40 0xb0 0xc0 0xd0 * managed: 0x40 0xb0 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * P2P-device: 0x40 0xd0 Supported extended features: * [ RRM ]: RRM * [ FILS_STA ]: STA FILS (Fast Initial Link Setup) * [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211 * [ SCAN_RANDOM_SN ]: use random sequence numbers in scans * [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans * [ CAN_REPLACE_PTK0 ]: can safely replace PTK 0 when rekeying * [ EXT_KEY_ID ]: Extended Key ID support * [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support * [ DEL_IBSS_STA ]: deletion of IBSS station support * [ SCAN_FREQ_KHZ ]: scan on kHz frequency support * [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support Wiphy phy0 wiphy index: 0 max # scan SSIDs: 10 max scan IEs length: 256 bytes max # sched scan SSIDs: 10 max # match sets: 10 Fragmentation threshold: 2346 RTS threshold: 2347 Retry short limit: 9 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports AP-side u-APSD. Device supports T-DLS. Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP-128 (00-0f-ac:4) * WPI-SMS4 (00-14-72:1) * CMAC (00-0f-ac:6) Available Antennas: TX 0x3 RX 0x3 Configured Antennas: TX 0x3 RX 0x3 Supported interface modes: * managed * AP * P2P-client * P2P-GO Band 1: Capabilities: 0x2ff RX LDPC HT20/HT40 SM Power Save disabled RX Greenfield RX HT20 SGI RX HT40 SGI TX STBC RX STBC 2-streams Max AMSDU length: 3839 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: No restriction (0x00) HT TX/RX MCS rate indexes supported: 0-15, 32 VHT Capabilities (0x33c179b0): Max MPDU length: 3895 Supported Channel Width: neither 160 nor 80+80 RX LDPC short GI (80 MHz) TX STBC SU Beamformer SU Beamformee +HTC-VHT RX antenna pattern consistency TX antenna pattern consistency VHT RX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT RX highest supported: 0 Mbps VHT TX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT TX highest supported: 0 Mbps VHT extended NSS: not supported Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps * 5.5 Mbps * 11.0 Mbps * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) * 2472 MHz [13] (20.0 dBm) * 2484 MHz [14] (disabled) Band 2: Capabilities: 0x2ff RX LDPC HT20/HT40 SM Power Save disabled RX Greenfield RX HT20 SGI RX HT40 SGI TX STBC RX STBC 2-streams Max AMSDU length: 3839 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: No restriction (0x00) HT TX/RX MCS rate indexes supported: 0-15, 32 VHT Capabilities (0x33c179b0): Max MPDU length: 3895 Supported Channel Width: neither 160 nor 80+80 RX LDPC short GI (80 MHz) TX STBC SU Beamformer SU Beamformee +HTC-VHT RX antenna pattern consistency TX antenna pattern consistency VHT RX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT RX highest supported: 0 Mbps VHT TX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT TX highest supported: 0 Mbps VHT extended NSS: not supported Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Frequencies: * 5040 MHz [8] (disabled) * 5060 MHz [12] (disabled) * 5080 MHz [16] (disabled) * 5170 MHz [34] (23.0 dBm) * 5190 MHz [38] (23.0 dBm) * 5210 MHz [42] (23.0 dBm) * 5230 MHz [46] (23.0 dBm) * 5180 MHz [36] (23.0 dBm) * 5200 MHz [40] (23.0 dBm) * 5220 MHz [44] (23.0 dBm) * 5240 MHz [48] (23.0 dBm) * 5260 MHz [52] (20.0 dBm) (no IR, radar detection) * 5280 MHz [56] (20.0 dBm) (no IR, radar detection) * 5300 MHz [60] (20.0 dBm) (no IR, radar detection) * 5320 MHz [64] (20.0 dBm) (no IR, radar detection) * 5500 MHz [100] (26.0 dBm) (no IR, radar detection) * 5520 MHz [104] (26.0 dBm) (no IR, radar detection) * 5540 MHz [108] (26.0 dBm) (no IR, radar detection) * 5560 MHz [112] (26.0 dBm) (no IR, radar detection) * 5580 MHz [116] (26.0 dBm) (no IR, radar detection) * 5600 MHz [120] (26.0 dBm) (no IR, radar detection) * 5620 MHz [124] (26.0 dBm) (no IR, radar detection) * 5640 MHz [128] (26.0 dBm) (no IR, radar detection) * 5660 MHz [132] (26.0 dBm) (no IR, radar detection) * 5680 MHz [136] (26.0 dBm) (no IR, radar detection) * 5700 MHz [140] (26.0 dBm) (no IR, radar detection) * 5745 MHz [149] (13.0 dBm) * 5765 MHz [153] (13.0 dBm) * 5785 MHz [157] (13.0 dBm) * 5805 MHz [161] (13.0 dBm) * 5825 MHz [165] (13.0 dBm) Supported commands: * new_interface * set_interface * new_key * start_ap * new_station * join_ibss * remain_on_channel * set_tx_bitrate_mask * frame * set_channel * tdls_mgmt * tdls_oper * start_sched_scan * connect * disconnect * channel_switch WoWLAN support: * wake up on disconnect * wake up on magic packet * wake up on pattern match, up to 10 patterns of 1-40 bytes, maximum packet offset 100 bytes * can do GTK rekeying * wake up on GTK rekey failure * wake up on network detection, up to 10 match sets software interface modes (can always be added): valid interface combinations: * #{ managed, AP, P2P-client, P2P-GO } <= 3, total <= 3, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz } Device supports TX status socket option. Device has client inactivity timer. Device supports low priority scan. Device supports scan flush. Userspace should do OBSS scan and generate 20/40 coex reports Device supports TDLS channel switching Device supports randomizing MAC-addr in scans. Device supports randomizing MAC-addr in sched scans. Device supports randomizing MAC-addr in net-detect scans. max # scan plans: 1 max scan plan interval: -1 max scan plan iterations: 0 Supported TX frame types: * managed: 0x50 0xd0 * AP: 0x50 0xd0 * P2P-client: 0x50 0xd0 * P2P-GO: 0x50 0xd0 Supported RX frame types: * managed: 0x40 0xd0 * AP: 0x40 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x40 0xd0 Coalesce support: * Maximum 8 coalesce rules supported * Each rule contains up to 4 patterns of 1-40 bytes, maximum packet offset 100 bytes * Maximum supported coalescing delay 100 msecs Supported extended features:


Hardware for Linux and BSD

GitHub