/dev/nvme0n1 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.10-gentoo-x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: Samsung SSD 980 PRO 1TB Serial Number: -- Firmware Version: 3B2QGXA7 PCI Vendor/Subsystem ID: 0x144d IEEE OUI Identifier: 0x002538 Total NVM Capacity: 1,000,204,886,016 [1.00 TB] Unallocated NVM Capacity: 0 Controller ID: 6 NVMe Version: 1.3 Number of Namespaces: 1 Namespace 1 Size/Capacity: 1,000,204,886,016 [1.00 TB] Namespace 1 Utilization: 434,910,167,040 [434 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 002538 ... Local Time is: Wed Feb 23 16:53:25 2022 PST Firmware Updates (0x16): 3 Slots, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x0057): Comp Wr_Unc DS_Mngmt Sav/Sel_Feat Timestmp Log Page Attributes (0x0f): S/H_per_NS Cmd_Eff_Lg Ext_Get_Lg Telmtry_Lg Maximum Data Transfer Size: 128 Pages Warning Comp. Temp. Threshold: 82 Celsius Critical Comp. Temp. Threshold: 85 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 8.49W - - 0 0 0 0 0 0 1 + 4.48W - - 1 1 1 1 0 200 2 + 3.18W - - 2 2 2 2 0 1000 3 - 0.0400W - - 3 3 3 3 2000 1200 4 - 0.0050W - - 4 4 4 4 500 9500 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 37 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 0% Data Units Read: 8,246,081 [4.22 TB] Data Units Written: 6,203,894 [3.17 TB] Host Read Commands: 92,663,631 Host Write Commands: 38,603,674 Controller Busy Time: 1,292 Power Cycles: 189 Power On Hours: 393 Unsafe Shutdowns: 20 Media and Data Integrity Errors: 0 Error Information Log Entries: 0 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 37 Celsius Temperature Sensor 2: 41 Celsius Error Information (NVMe Log 0x01, 16 of 64 entries) No Errors Logged /dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.10-gentoo-x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Pro Device Model: WDC WD8003FFBX-68B9AN0 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: 83.00A83 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Feb 23 16:53:25 2022 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 164 (intermediate level without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 87) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 863) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance --S--- 133 133 054 - 92 3 Spin_Up_Time POS--- 162 162 024 - 446 (Average 556) 4 Start_Stop_Count -O--C- 100 100 000 - 509 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate -O-R-- 100 100 067 - 0 8 Seek_Time_Performance --S--- 128 128 020 - 18 9 Power_On_Hours -O--C- 099 099 000 - 7136 10 Spin_Retry_Count -O--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 502 192 Power-Off_Retract_Count -O--CK 099 099 000 - 1510 193 Load_Cycle_Count -O--C- 099 099 000 - 1510 194 Temperature_Celsius -O---- 150 150 000 - 40 (Min/Max 17/54) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 5501 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL R/W 1 Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x2f GPL - 1 Set Sector Configuration 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 19/41 Celsius Lifetime Min/Max Temperature: 17/54 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (10) Index Estimated Time Temperature Celsius 11 2022-02-23 14:46 40 ********************* ... ..( 34 skipped). .. ********************* 46 2022-02-23 15:21 40 ********************* 47 2022-02-23 15:22 41 ********************** 48 2022-02-23 15:23 40 ********************* ... ..( 28 skipped). .. ********************* 77 2022-02-23 15:52 40 ********************* 78 2022-02-23 15:53 41 ********************** ... ..( 24 skipped). .. ********************** 103 2022-02-23 16:18 41 ********************** 104 2022-02-23 16:19 40 ********************* ... ..( 33 skipped). .. ********************* 10 2022-02-23 16:53 40 ********************* SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 502 --- Lifetime Power-On Resets 0x01 0x010 4 7136 --- Power-on Hours 0x01 0x018 6 26586308354 --- Logical Sectors Written 0x01 0x020 6 72086680 --- Number of Write Commands 0x01 0x028 6 19650665347 --- Logical Sectors Read 0x01 0x030 6 170433901 --- Number of Read Commands 0x01 0x038 6 25691574300 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 7017 --- Spindle Motor Power-on Hours 0x03 0x010 4 7017 --- Head Flying Hours 0x03 0x018 4 1510 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 40 --- Current Temperature 0x05 0x010 1 37 N-- Average Short Term Temperature 0x05 0x018 1 38 N-- Average Long Term Temperature 0x05 0x020 1 54 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 44 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 40 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 2099 --- Number of Hardware Resets 0x06 0x010 4 245 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.10-gentoo-x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Green Device Model: WDC WD60EZRX-00MVLB1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5700 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Feb 23 16:53:25 2022 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2384) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 678) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 196 196 021 - 9166 4 Start_Stop_Count -O--CK 099 099 000 - 1561 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 024 024 000 - 55984 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 810 192 Power-Off_Retract_Count -O--CK 200 200 000 - 314 193 Load_Cycle_Count -O--CK 001 001 000 - 628207 194 Temperature_Celsius -O---K 119 109 000 - 33 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 40 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 20/33 Celsius Lifetime Min/Max Temperature: 2/43 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (95) Index Estimated Time Temperature Celsius 96 2022-02-23 08:56 32 ************* ... ..( 15 skipped). .. ************* 112 2022-02-23 09:12 32 ************* 113 2022-02-23 09:13 31 ************ ... ..( 29 skipped). .. ************ 143 2022-02-23 09:43 31 ************ 144 2022-02-23 09:44 32 ************* ... ..( 42 skipped). .. ************* 187 2022-02-23 10:27 32 ************* 188 2022-02-23 10:28 33 ************** ... ..(114 skipped). .. ************** 303 2022-02-23 12:23 33 ************** 304 2022-02-23 12:24 32 ************* 305 2022-02-23 12:25 32 ************* 306 2022-02-23 12:26 28 ********* ... ..( 5 skipped). .. ********* 312 2022-02-23 12:32 28 ********* 313 2022-02-23 12:33 29 ********** ... ..( 48 skipped). .. ********** 362 2022-02-23 13:22 29 ********** 363 2022-02-23 13:23 30 *********** ... ..( 8 skipped). .. *********** 372 2022-02-23 13:32 30 *********** 373 2022-02-23 13:33 31 ************ ... ..( 86 skipped). .. ************ 460 2022-02-23 15:00 31 ************ 461 2022-02-23 15:01 30 *********** ... ..( 49 skipped). .. *********** 33 2022-02-23 15:51 30 *********** 34 2022-02-23 15:52 31 ************ ... ..( 35 skipped). .. ************ 70 2022-02-23 16:28 31 ************ 71 2022-02-23 16:29 32 ************* ... ..( 23 skipped). .. ************* 95 2022-02-23 16:53 32 ************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 31821 Vendor specific /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.10-gentoo-x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 (SMR) Device Model: ST8000DM004-2CX188 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0001 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5425 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Feb 23 16:53:25 2022 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 983) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30a5) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 076 064 006 - 42195937 3 Spin_Up_Time PO---- 092 092 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 177 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 078 060 045 - 59105321 9 Power_On_Hours -O--CK 098 098 000 - 2185h+50m+08.997s 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 177 183 Runtime_Bad_Block -O--CK 099 099 000 - 1 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 0 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 065 059 040 - 35 (Min/Max 22/36) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 51 193 Load_Cycle_Count -O--CK 100 100 000 - 323 194 Temperature_Celsius -O---K 035 041 000 - 35 (0 20 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 076 064 000 - 42195937 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 199 000 - 4 240 Head_Flying_Hours ------ 100 253 000 - 2009h+41m+32.061s 241 Total_LBAs_Written ------ 100 253 000 - 15910654456 242 Total_LBAs_Read ------ 100 253 000 - 8003233438 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 24 Device vendor specific log 0xa2 GPL VS 8160 Device vendor specific log 0xa6 GPL VS 192 Device vendor specific log 0xa8-0xa9 GPL,SL VS 136 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 9048 Device vendor specific log 0xbd GPL VS 8 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 16 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xc4 GPL,SL VS 24 Device vendor specific log 0xd1 GPL VS 264 Device vendor specific log 0xd3 GPL VS 1920 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 22/36 Celsius Lifetime Min/Max Temperature: 20/41 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 3 minutes Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (107) Index Estimated Time Temperature Celsius 108 2022-02-18 11:11 36 ***************** 109 2022-02-18 12:10 34 *************** 110 2022-02-18 13:09 34 *************** 111 2022-02-18 14:08 35 **************** 112 2022-02-18 15:07 36 ***************** 113 2022-02-18 16:06 ? - 114 2022-02-18 17:05 21 ** 115 2022-02-18 18:04 32 ************* 116 2022-02-18 19:03 34 *************** 117 2022-02-18 20:02 34 *************** 118 2022-02-18 21:01 35 **************** 119 2022-02-18 22:00 35 **************** 120 2022-02-18 22:59 34 *************** 121 2022-02-18 23:58 35 **************** 122 2022-02-19 00:57 35 **************** 123 2022-02-19 01:56 34 *************** 124 2022-02-19 02:55 34 *************** 125 2022-02-19 03:54 35 **************** ... ..( 2 skipped). .. **************** 0 2022-02-19 06:51 35 **************** 1 2022-02-19 07:50 34 *************** 2 2022-02-19 08:49 34 *************** 3 2022-02-19 09:48 34 *************** 4 2022-02-19 10:47 33 ************** ... ..( 5 skipped). .. ************** 10 2022-02-19 16:41 33 ************** 11 2022-02-19 17:40 34 *************** 12 2022-02-19 18:39 35 **************** 13 2022-02-19 19:38 34 *************** 14 2022-02-19 20:37 35 **************** 15 2022-02-19 21:36 35 **************** 16 2022-02-19 22:35 35 **************** 17 2022-02-19 23:34 ? - 18 2022-02-20 00:33 33 ************** 19 2022-02-20 01:32 ? - 20 2022-02-20 02:31 34 *************** 21 2022-02-20 03:30 36 ***************** 22 2022-02-20 04:29 37 ****************** 23 2022-02-20 05:28 36 ***************** 24 2022-02-20 06:27 ? - 25 2022-02-20 07:26 21 ** 26 2022-02-20 08:25 33 ************** 27 2022-02-20 09:24 35 **************** 28 2022-02-20 10:23 34 *************** 29 2022-02-20 11:22 34 *************** 30 2022-02-20 12:21 35 **************** 31 2022-02-20 13:20 36 ***************** 32 2022-02-20 14:19 33 ************** 33 2022-02-20 15:18 36 ***************** 34 2022-02-20 16:17 36 ***************** 35 2022-02-20 17:16 36 ***************** 36 2022-02-20 18:15 ? - 37 2022-02-20 19:14 21 ** 38 2022-02-20 20:13 32 ************* 39 2022-02-20 21:12 34 *************** 40 2022-02-20 22:11 34 *************** 41 2022-02-20 23:10 ? - 42 2022-02-21 00:09 35 **************** 43 2022-02-21 01:08 ? - 44 2022-02-21 02:07 35 **************** 45 2022-02-21 03:06 ? - 46 2022-02-21 04:05 35 **************** 47 2022-02-21 05:04 ? - 48 2022-02-21 06:03 35 **************** 49 2022-02-21 07:02 ? - 50 2022-02-21 08:01 35 **************** 51 2022-02-21 09:00 34 *************** 52 2022-02-21 09:59 33 ************** 53 2022-02-21 10:58 36 ***************** 54 2022-02-21 11:57 ? - 55 2022-02-21 12:56 24 ***** 56 2022-02-21 13:55 34 *************** 57 2022-02-21 14:54 34 *************** 58 2022-02-21 15:53 ? - 59 2022-02-21 16:52 22 *** 60 2022-02-21 17:51 33 ************** 61 2022-02-21 18:50 ? - 62 2022-02-21 19:49 31 ************ 63 2022-02-21 20:48 35 **************** 64 2022-02-21 21:47 35 **************** 65 2022-02-21 22:46 ? - 66 2022-02-21 23:45 23 **** 67 2022-02-22 00:44 33 ************** 68 2022-02-22 01:43 35 **************** ... ..( 2 skipped). .. **************** 71 2022-02-22 04:40 35 **************** 72 2022-02-22 05:39 36 ***************** 73 2022-02-22 06:38 36 ***************** 74 2022-02-22 07:37 ? - 75 2022-02-22 08:36 35 **************** 76 2022-02-22 09:35 35 **************** 77 2022-02-22 10:34 ? - 78 2022-02-22 11:33 32 ************* 79 2022-02-22 12:32 35 **************** 80 2022-02-22 13:31 35 **************** 81 2022-02-22 14:30 35 **************** 82 2022-02-22 15:29 ? - 83 2022-02-22 16:28 22 *** 84 2022-02-22 17:27 32 ************* 85 2022-02-22 18:26 33 ************** 86 2022-02-22 19:25 33 ************** 87 2022-02-22 20:24 34 *************** 88 2022-02-22 21:23 34 *************** 89 2022-02-22 22:22 35 **************** 90 2022-02-22 23:21 34 *************** 91 2022-02-23 00:20 35 **************** ... ..( 2 skipped). .. **************** 94 2022-02-23 03:17 35 **************** 95 2022-02-23 04:16 ? - 96 2022-02-23 05:15 22 *** 97 2022-02-23 06:14 32 ************* 98 2022-02-23 07:13 ? - 99 2022-02-23 08:12 22 *** 100 2022-02-23 09:11 32 ************* 101 2022-02-23 10:10 34 *************** 102 2022-02-23 11:09 34 *************** 103 2022-02-23 12:08 33 ************** 104 2022-02-23 13:07 35 **************** 105 2022-02-23 14:06 34 *************** 106 2022-02-23 15:05 36 ***************** 107 2022-02-23 16:04 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 177 --- Lifetime Power-On Resets 0x01 0x010 4 2185 --- Power-on Hours 0x01 0x018 6 15874198880 --- Logical Sectors Written 0x01 0x020 6 22478006 --- Number of Write Commands 0x01 0x028 6 8003637598 --- Logical Sectors Read 0x01 0x030 6 23938671 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 2183 --- Spindle Motor Power-on Hours 0x03 0x010 4 2010 --- Head Flying Hours 0x03 0x018 4 323 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 51 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 35 --- Current Temperature 0x05 0x010 1 33 --- Average Short Term Temperature 0x05 0x018 1 33 --- Average Long Term Temperature 0x05 0x020 1 41 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 37 --- Highest Average Short Term Temperature 0x05 0x038 1 32 --- Lowest Average Short Term Temperature 0x05 0x040 1 34 --- Highest Average Long Term Temperature 0x05 0x048 1 33 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 244 --- Number of Hardware Resets 0x06 0x010 4 117 --- Number of ASR Events 0x06 0x018 4 4 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdd smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.10-gentoo-x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 850 PRO 256GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EXM01B6Q User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Feb 23 16:53:25 2022 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Unexpected SCT status 0x0001 (action_code=4, function_code=2) Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 17) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 087 087 000 - 64895 12 Power_Cycle_Count -O--CK 099 099 000 - 830 177 Wear_Leveling_Count PO--C- 097 097 000 - 128 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 062 052 000 - 38 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 269 241 Total_LBAs_Written -O--CK 099 099 000 - 65025273936 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 16 Device vendor specific log 0xa5 GPL,SL VS 16 Device vendor specific log 0xce GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: ?/ ? Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/310411 SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: ?/ ? Celsius Min/Max Temperature Limit: ?/ ? Celsius Temperature History Size (Index): 128 (53) Index Estimated Time Temperature Celsius 54 2022-02-22 19:40 ? - ... ..( 73 skipped). .. - 0 2022-02-23 08:00 ? - 1 2022-02-23 08:10 24 ***** 2 2022-02-23 08:20 26 ******* 3 2022-02-23 08:30 32 ************* 4 2022-02-23 08:40 32 ************* 5 2022-02-23 08:50 31 ************ 6 2022-02-23 09:00 31 ************ 7 2022-02-23 09:10 31 ************ 8 2022-02-23 09:20 35 **************** 9 2022-02-23 09:30 32 ************* 10 2022-02-23 09:40 33 ************** 11 2022-02-23 09:50 34 *************** 12 2022-02-23 10:00 32 ************* 13 2022-02-23 10:10 32 ************* 14 2022-02-23 10:20 33 ************** 15 2022-02-23 10:30 34 *************** 16 2022-02-23 10:40 38 ******************* 17 2022-02-23 10:50 35 **************** 18 2022-02-23 11:00 35 **************** 19 2022-02-23 11:10 35 **************** 20 2022-02-23 11:20 33 ************** 21 2022-02-23 11:30 32 ************* 22 2022-02-23 11:40 31 ************ 23 2022-02-23 11:50 32 ************* 24 2022-02-23 12:00 36 ***************** 25 2022-02-23 12:10 39 ******************** 26 2022-02-23 12:20 38 ******************* 27 2022-02-23 12:30 37 ****************** 28 2022-02-23 12:40 36 ***************** 29 2022-02-23 12:50 42 *********************** 30 2022-02-23 13:00 43 ************************ 31 2022-02-23 13:10 44 ************************* 32 2022-02-23 13:20 43 ************************ 33 2022-02-23 13:30 41 ********************** 34 2022-02-23 13:40 41 ********************** 35 2022-02-23 13:50 40 ********************* 36 2022-02-23 14:00 39 ******************** 37 2022-02-23 14:10 40 ********************* 38 2022-02-23 14:20 40 ********************* 39 2022-02-23 14:30 39 ******************** 40 2022-02-23 14:40 40 ********************* 41 2022-02-23 14:50 40 ********************* 42 2022-02-23 15:00 40 ********************* 43 2022-02-23 15:10 41 ********************** 44 2022-02-23 15:20 40 ********************* 45 2022-02-23 15:30 40 ********************* 46 2022-02-23 15:40 41 ********************** 47 2022-02-23 15:50 40 ********************* 48 2022-02-23 16:00 40 ********************* 49 2022-02-23 16:10 38 ******************* 50 2022-02-23 16:20 38 ******************* 51 2022-02-23 16:30 37 ****************** 52 2022-02-23 16:40 38 ******************* 53 2022-02-23 16:50 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC