/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.6-desktop-1omv2390] (OpenMandriva Lx 7.3-3) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F2 EG Device Model: SAMSUNG HD103SI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AG01118 User Capacity: 1,000,203,804,160 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Sat Apr 1 21:44:08 2023 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12980) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 217) minutes. Conveyance self-test routine recommended polling time: ( 23) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 099 051 - 2 3 Spin_Up_Time POS--- 082 082 011 - 6270 4 Start_Stop_Count -O--CK 097 097 000 - 2904 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 100 100 051 - 0 8 Seek_Time_Performance P-S--K 100 100 015 - 0 9 Power_On_Hours -O--CK 098 098 000 - 9986 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2462 13 Read_Soft_Error_Rate -OSR-- 100 099 000 - 2 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 4 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 056 000 - 37 (Min/Max 37/37) 194 Temperature_Celsius -O---K 063 055 000 - 37 (Min/Max 37/37) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 94005 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 2 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 701 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL R/O 2 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 2 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 703 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 703 [6] occurred at disk power-on lifetime: 9560 hours (398 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 42 00 00 00 00 6c 7c 69 62 40 00 at LBA = 0x6c7c6962 = 1820092770 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 7c 69 60 40 00 04:56:12.490 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 7c 69 58 40 00 04:56:12.490 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 7c 69 50 40 00 04:56:12.490 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 7c 69 48 40 00 04:56:12.490 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 7c 69 40 40 00 04:56:12.490 READ FPDMA QUEUED Error 702 [5] occurred at disk power-on lifetime: 9560 hours (398 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 52 00 00 00 00 6c 7c 69 63 40 00 at LBA = 0x6c7c6963 = 1820092771 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 00 00 7c 68 40 40 00 04:56:09.740 READ FPDMA QUEUED 60 00 00 02 00 00 00 00 7c 66 40 40 00 04:56:09.730 READ FPDMA QUEUED 60 00 00 06 00 00 00 00 7c 60 40 40 00 04:56:09.720 READ FPDMA QUEUED 60 00 00 04 00 00 00 00 7c 5c 40 40 00 04:56:09.710 READ FPDMA QUEUED 60 00 00 06 00 00 00 00 7c 56 40 40 00 04:56:09.700 READ FPDMA QUEUED Error 701 [4] occurred at disk power-on lifetime: 2188 hours (91 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- d0 00 80 00 00 3a 38 97 d9 e0 00 128 sectors at LBA = 0x3a3897d9 = 976787417 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 3a 38 97 59 e0 00 00:01:57.230 READ DMA EXT 25 00 00 00 80 00 00 3a 38 96 d9 e0 00 00:01:57.230 READ DMA EXT 25 00 00 00 80 00 00 3a 38 96 59 e0 00 00:01:57.200 READ DMA EXT 25 00 00 00 80 00 00 3a 38 95 d9 e0 00 00:01:57.200 READ DMA EXT 25 00 00 00 80 00 00 3a 38 95 59 e0 00 00:01:57.200 READ DMA EXT Error 700 [3] occurred at disk power-on lifetime: 2188 hours (91 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- d0 00 80 00 00 3a 38 80 d9 e0 00 128 sectors at LBA = 0x3a3880d9 = 976781529 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 3a 38 80 59 e0 00 00:01:56.920 READ DMA EXT 25 00 00 00 80 00 00 3a 38 7f d9 e0 00 00:01:56.920 READ DMA EXT 25 00 00 00 80 00 00 3a 38 7f 59 e0 00 00:01:56.920 READ DMA EXT 25 00 00 00 80 00 00 3a 38 7e d9 e0 00 00:01:56.920 READ DMA EXT 25 00 00 00 80 00 00 3a 38 7e 59 e0 00 00:01:56.890 READ DMA EXT Error 699 [2] occurred at disk power-on lifetime: 2188 hours (91 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- d2 00 01 00 00 00 5e 00 12 e0 00 1 sectors at LBA = 0x005e0012 = 6160402 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 3a 38 77 21 e0 00 00:01:29.390 READ DMA EXT Error 698 [1] occurred at disk power-on lifetime: 2188 hours (91 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 53 00 00 00 00 3a 38 77 28 e0 00 Error: ICRC, ABRT at LBA = 0x3a387728 = 976779048 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 3a 38 77 21 e0 00 00:01:29.370 READ DMA EXT 25 00 00 00 08 00 00 3a 38 77 19 e0 00 00:01:29.370 READ DMA EXT 25 00 00 00 08 00 00 3a 38 77 11 e0 00 00:01:29.370 READ DMA EXT 25 00 00 00 08 00 00 3a 38 77 09 e0 00 00:01:29.370 READ DMA EXT 25 00 00 00 08 00 00 3a 38 77 01 e0 00 00:01:29.370 READ DMA EXT Error 697 [0] occurred at disk power-on lifetime: 2188 hours (91 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- d0 00 08 00 00 3a 38 76 e1 e0 00 8 sectors at LBA = 0x3a3876e1 = 976778977 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 3a 38 76 e1 e0 00 00:01:29.360 READ DMA EXT 25 00 00 00 08 00 00 3a 38 76 d9 e0 00 00:01:29.350 READ DMA EXT ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:01:29.350 SET FEATURES [Set transfer mode] 00 00 00 00 01 00 00 00 00 00 01 a0 00 00:01:29.330 NOP [Abort queued commands] 25 00 00 00 80 00 00 3a 38 7e 59 e0 00 00:01:29.330 READ DMA EXT Error 696 [7] occurred at disk power-on lifetime: 2188 hours (91 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- d0 00 80 00 00 3a 38 77 59 e0 00 128 sectors at LBA = 0x3a387759 = 976779097 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 3a 38 76 d9 e0 00 00:01:28.980 READ DMA EXT 25 00 00 00 80 00 00 3a 38 76 59 e0 00 00:01:28.950 READ DMA EXT 25 00 00 00 80 00 00 3a 38 75 d9 e0 00 00:01:28.950 READ DMA EXT 25 00 00 00 80 00 00 3a 38 75 59 e0 00 00:01:28.950 READ DMA EXT 25 00 00 00 80 00 00 3a 38 74 d9 e0 00 00:01:28.950 READ DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: --/37 Celsius Lifetime Min/Max Temperature: --/45 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (101) Index Estimated Time Temperature Celsius 102 2023-04-01 19:37 33 ************** ... ..( 2 skipped). .. ************** 105 2023-04-01 19:40 33 ************** 106 2023-04-01 19:41 34 *************** ... ..( 2 skipped). .. *************** 109 2023-04-01 19:44 34 *************** 110 2023-04-01 19:45 35 **************** 111 2023-04-01 19:46 35 **************** 112 2023-04-01 19:47 35 **************** 113 2023-04-01 19:48 34 *************** ... ..( 2 skipped). .. *************** 116 2023-04-01 19:51 34 *************** 117 2023-04-01 19:52 35 **************** ... ..( 7 skipped). .. **************** 125 2023-04-01 20:00 35 **************** 126 2023-04-01 20:01 36 ***************** 127 2023-04-01 20:02 36 ***************** 0 2023-04-01 20:03 38 ******************* 1 2023-04-01 20:04 37 ****************** ... ..( 6 skipped). .. ****************** 8 2023-04-01 20:11 37 ****************** 9 2023-04-01 20:12 38 ******************* 10 2023-04-01 20:13 37 ****************** ... ..( 90 skipped). .. ****************** 101 2023-04-01 21:44 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read Device Statistics page 0x00 failed Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC