/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.14-desktop-1omv4002] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST1000LM024 HN-M101MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2BA30004 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Feb 15 01:33:11 2021 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11940) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 199) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 23 2 Throughput_Performance -OS--K 055 042 000 - 10890 3 Spin_Up_Time PO---K 089 083 025 - 3409 4 Start_Stop_Count -O--CK 098 098 000 - 2733 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 11389 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 43 12 Power_Cycle_Count -O--CK 099 099 000 - 1885 191 G-Sense_Error_Rate -O---K 100 100 000 - 213 192 Power-Off_Retract_Count -O---K 100 100 000 - 122 194 Temperature_Celsius -O---- 063 045 000 - 37 (Min/Max 20/55) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 19611 223 Load_Retry_Count -O--CK 100 100 000 - 43 225 Load_Cycle_Count -O--CK 094 094 000 - 65592 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 11377 - # 2 Short offline Completed without error 00% 11364 - # 3 Short offline Completed without error 00% 11351 - # 4 Short offline Completed without error 00% 11319 - # 5 Short offline Completed without error 00% 11285 - # 6 Extended offline Completed without error 00% 11276 - # 7 Short offline Completed without error 00% 11267 - # 8 Short offline Completed without error 00% 11253 - # 9 Short offline Completed without error 00% 11224 - #10 Short offline Completed without error 00% 11208 - #11 Short offline Completed without error 00% 11193 - #12 Short offline Completed without error 00% 11182 - #13 Short offline Completed without error 00% 11172 - #14 Short offline Completed without error 00% 11156 - #15 Short offline Completed without error 00% 11141 - #16 Short offline Completed without error 00% 11126 - #17 Short offline Completed without error 00% 11110 - #18 Short offline Completed without error 00% 11094 - #19 Short offline Completed without error 00% 11083 - #20 Short offline Completed without error 00% 11081 - #21 Short offline Completed without error 00% 11051 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 31/37 Celsius Lifetime Min/Max Temperature: 20/55 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (36) Index Estimated Time Temperature Celsius 37 2021-02-14 14:55 37 ****************** 38 2021-02-14 15:00 38 ******************* ... ..( 2 skipped). .. ******************* 41 2021-02-14 15:15 38 ******************* 42 2021-02-14 15:20 37 ****************** ... ..( 8 skipped). .. ****************** 51 2021-02-14 16:05 37 ****************** 52 2021-02-14 16:10 38 ******************* 53 2021-02-14 16:15 38 ******************* 54 2021-02-14 16:20 38 ******************* 55 2021-02-14 16:25 39 ******************** 56 2021-02-14 16:30 39 ******************** 57 2021-02-14 16:35 40 ********************* ... ..( 4 skipped). .. ********************* 62 2021-02-14 17:00 40 ********************* 63 2021-02-14 17:05 39 ******************** ... ..( 2 skipped). .. ******************** 66 2021-02-14 17:20 39 ******************** 67 2021-02-14 17:25 40 ********************* 68 2021-02-14 17:30 41 ********************** 69 2021-02-14 17:35 40 ********************* 70 2021-02-14 17:40 41 ********************** 71 2021-02-14 17:45 40 ********************* ... ..( 3 skipped). .. ********************* 75 2021-02-14 18:05 40 ********************* 76 2021-02-14 18:10 41 ********************** 77 2021-02-14 18:15 41 ********************** 78 2021-02-14 18:20 41 ********************** 79 2021-02-14 18:25 42 *********************** ... ..( 3 skipped). .. *********************** 83 2021-02-14 18:45 42 *********************** 84 2021-02-14 18:50 41 ********************** 85 2021-02-14 18:55 41 ********************** 86 2021-02-14 19:00 40 ********************* ... ..( 13 skipped). .. ********************* 100 2021-02-14 20:10 40 ********************* 101 2021-02-14 20:15 41 ********************** 102 2021-02-14 20:20 41 ********************** 103 2021-02-14 20:25 42 *********************** ... ..( 9 skipped). .. *********************** 113 2021-02-14 21:15 42 *********************** 114 2021-02-14 21:20 41 ********************** 115 2021-02-14 21:25 40 ********************* ... ..( 10 skipped). .. ********************* 126 2021-02-14 22:20 40 ********************* 127 2021-02-14 22:25 41 ********************** 0 2021-02-14 22:30 40 ********************* 1 2021-02-14 22:35 40 ********************* 2 2021-02-14 22:40 39 ******************** ... ..( 19 skipped). .. ******************** 22 2021-02-15 00:20 39 ******************** 23 2021-02-15 00:25 40 ********************* ... ..( 2 skipped). .. ********************* 26 2021-02-15 00:40 40 ********************* 27 2021-02-15 00:45 39 ******************** 28 2021-02-15 00:50 40 ********************* 29 2021-02-15 00:55 40 ********************* 30 2021-02-15 01:00 40 ********************* 31 2021-02-15 01:05 39 ******************** 32 2021-02-15 01:10 39 ******************** 33 2021-02-15 01:15 39 ******************** 34 2021-02-15 01:20 35 **************** 35 2021-02-15 01:25 37 ****************** 36 2021-02-15 01:30 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 6 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific