/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.10.0-7-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD5000AAKX-60U6AA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 18.01H18 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Oct 26 14:49:36 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8700) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 88) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 139 138 021 - 4041 4 Start_Stop_Count -O--CK 099 099 000 - 1300 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 200 200 051 - 0 9 Power_On_Hours -O--CK 093 093 000 - 5711 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1271 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 099 000 - 1 188 Command_Timeout -O--CK 100 099 000 - 4295032838 190 Airflow_Temperature_Cel -O---K 068 057 040 - 32 (Min/Max 31/32) 192 Power-Off_Retract_Count -O--CK 200 200 000 - 68 193 Load_Cycle_Count -O--CK 200 200 000 - 1231 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 2230 hours (92 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 85 5c 33 40 00 Error: UNC at LBA = 0x01855c33 = 25517107 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 60 00 00 15 ba a0 18 40 00 22:08:16.383 READ FPDMA QUEUED 60 00 02 00 58 00 00 01 85 5c 32 40 00 22:08:16.368 READ FPDMA QUEUED 60 00 08 00 50 00 00 18 5a 60 60 40 00 22:08:16.352 READ FPDMA QUEUED 60 00 03 00 48 00 00 01 85 5c 34 40 00 22:08:16.333 READ FPDMA QUEUED 60 00 08 00 40 00 00 01 85 5a 78 40 00 22:08:16.316 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 31/32 Celsius Lifetime Min/Max Temperature: 0/43 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (65) Index Estimated Time Temperature Celsius 66 2022-10-26 12:42 30 *********** ... ..( 3 skipped). .. *********** 70 2022-10-26 12:46 30 *********** 71 2022-10-26 12:47 31 ************ 72 2022-10-26 12:48 30 *********** ... ..( 4 skipped). .. *********** 77 2022-10-26 12:53 30 *********** 78 2022-10-26 12:54 31 ************ 79 2022-10-26 12:55 30 *********** 80 2022-10-26 12:56 30 *********** 81 2022-10-26 12:57 30 *********** 82 2022-10-26 12:58 31 ************ 83 2022-10-26 12:59 30 *********** 84 2022-10-26 13:00 31 ************ 85 2022-10-26 13:01 31 ************ 86 2022-10-26 13:02 30 *********** 87 2022-10-26 13:03 30 *********** 88 2022-10-26 13:04 31 ************ 89 2022-10-26 13:05 30 *********** 90 2022-10-26 13:06 31 ************ 91 2022-10-26 13:07 30 *********** 92 2022-10-26 13:08 31 ************ 93 2022-10-26 13:09 31 ************ 94 2022-10-26 13:10 30 *********** ... ..( 2 skipped). .. *********** 97 2022-10-26 13:13 30 *********** 98 2022-10-26 13:14 31 ************ 99 2022-10-26 13:15 30 *********** ... ..( 5 skipped). .. *********** 105 2022-10-26 13:21 30 *********** 106 2022-10-26 13:22 31 ************ 107 2022-10-26 13:23 30 *********** ... ..( 4 skipped). .. *********** 112 2022-10-26 13:28 30 *********** 113 2022-10-26 13:29 31 ************ 114 2022-10-26 13:30 30 *********** 115 2022-10-26 13:31 31 ************ 116 2022-10-26 13:32 30 *********** 117 2022-10-26 13:33 30 *********** 118 2022-10-26 13:34 31 ************ 119 2022-10-26 13:35 31 ************ 120 2022-10-26 13:36 30 *********** 121 2022-10-26 13:37 30 *********** 122 2022-10-26 13:38 31 ************ 123 2022-10-26 13:39 31 ************ 124 2022-10-26 13:40 31 ************ 125 2022-10-26 13:41 30 *********** 126 2022-10-26 13:42 31 ************ 127 2022-10-26 13:43 31 ************ 0 2022-10-26 13:44 32 ************* ... ..( 14 skipped). .. ************* 15 2022-10-26 13:59 32 ************* 16 2022-10-26 14:00 ? - 17 2022-10-26 14:01 25 ****** 18 2022-10-26 14:02 25 ****** 19 2022-10-26 14:03 26 ******* 20 2022-10-26 14:04 26 ******* 21 2022-10-26 14:05 27 ******** 22 2022-10-26 14:06 28 ********* 23 2022-10-26 14:07 28 ********* 24 2022-10-26 14:08 29 ********** ... ..( 4 skipped). .. ********** 29 2022-10-26 14:13 29 ********** 30 2022-10-26 14:14 30 *********** 31 2022-10-26 14:15 30 *********** 32 2022-10-26 14:16 30 *********** 33 2022-10-26 14:17 31 ************ 34 2022-10-26 14:18 30 *********** 35 2022-10-26 14:19 30 *********** 36 2022-10-26 14:20 31 ************ 37 2022-10-26 14:21 31 ************ 38 2022-10-26 14:22 31 ************ 39 2022-10-26 14:23 ? - 40 2022-10-26 14:24 32 ************* 41 2022-10-26 14:25 32 ************* 42 2022-10-26 14:26 32 ************* 43 2022-10-26 14:27 31 ************ 44 2022-10-26 14:28 ? - 45 2022-10-26 14:29 32 ************* 46 2022-10-26 14:30 32 ************* 47 2022-10-26 14:31 31 ************ 48 2022-10-26 14:32 32 ************* ... ..( 16 skipped). .. ************* 65 2022-10-26 14:49 32 ************* SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 1247 Vendor specific