/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-76-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: TOSHIBA THNSNF128GCSS Serial Number: -- Firmware Version: FSLAN102 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jul 5 11:10:53 2023 WIB SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 8) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--- 100 100 050 - 0 5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0 7 Unknown_SSD_Attribute PO-R-- 100 100 050 - 0 8 Unknown_SSD_Attribute P-S--- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 5606 10 Unknown_SSD_Attribute PO--C- 100 100 050 - 0 12 Power_Cycle_Count -O--C- 100 100 000 - 5048 167 Unknown_Attribute -O---K 100 100 000 - 0 168 Unknown_Attribute -O--C- 100 100 000 - 17 169 Unknown_Attribute PO--C- 100 100 010 - 100 170 Unknown_Attribute PO--C- 100 100 010 - 0 173 Unknown_Attribute -O--C- 183 183 000 - 0 175 Program_Fail_Count_Chip PO--C- 100 100 010 - 0 192 Power-Off_Retract_Count -O--C- 100 100 000 - 520 194 Temperature_Celsius -O---K 058 043 000 - 42 (Min/Max 5/57) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 240 Unknown_SSD_Attribute PO--C- 100 100 050 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 5 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 [4] occurred at disk power-on lifetime: 5558 hours (231 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 10 00 00 02 ec db 00 40 08 Error: ICRC, ABRT at LBA = 0x02ecdb00 = 49076992 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 10 00 00 02 ec db 00 40 08 00:00:56.978 READ FPDMA QUEUED 60 01 00 00 08 00 00 02 ec da 00 40 08 00:00:56.977 READ FPDMA QUEUED 60 01 00 00 00 00 00 02 ec d9 00 40 08 00:00:56.974 READ FPDMA QUEUED 60 01 00 00 f0 00 00 02 ec d8 00 40 08 00:00:56.972 READ FPDMA QUEUED 60 01 00 00 e8 00 00 02 ec d7 00 40 08 00:00:56.970 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 5558 hours (231 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 a8 00 00 04 cb f3 f8 40 08 Error: ICRC, ABRT at LBA = 0x04cbf3f8 = 80475128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 a8 00 00 04 cb f3 f8 40 08 00:00:16.922 READ FPDMA QUEUED 60 00 40 00 a0 00 00 0e 3c 4a 60 40 08 00:00:16.920 READ FPDMA QUEUED 60 00 40 00 98 00 00 0e 3c 4a 20 40 08 00:00:16.920 READ FPDMA QUEUED 60 00 20 00 90 00 00 0e 3c 4a 00 40 08 00:00:16.917 READ FPDMA QUEUED 60 00 20 00 88 00 00 02 5e 69 80 40 08 00:00:16.914 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 5558 hours (231 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 c8 00 00 0c 40 55 08 40 08 Error: ICRC, ABRT at LBA = 0x0c405508 = 205542664 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 48 00 d8 00 00 0c 40 55 b8 40 08 00:05:41.802 READ FPDMA QUEUED 60 00 08 00 d0 00 00 0c 40 55 b0 40 08 00:05:41.802 READ FPDMA QUEUED 60 00 a8 00 c8 00 00 0c 40 55 08 40 08 00:05:41.802 READ FPDMA QUEUED 60 00 08 00 c0 00 00 0c 41 19 f8 40 08 00:05:41.802 READ FPDMA QUEUED 60 00 58 00 b8 00 00 0c 40 59 a8 40 08 00:05:41.801 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 5558 hours (231 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 40 00 00 0e 57 91 00 40 08 Error: ICRC, ABRT at LBA = 0x0e579100 = 240619776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 40 00 00 0e 57 91 00 40 08 00:01:19.670 READ FPDMA QUEUED 60 01 00 00 38 00 00 0e 57 90 00 40 08 00:01:19.668 READ FPDMA QUEUED 60 01 00 00 30 00 00 0e 57 8f 00 40 08 00:01:19.666 READ FPDMA QUEUED 60 01 00 00 28 00 00 0e 57 8e 00 40 08 00:01:19.664 READ FPDMA QUEUED 60 01 00 00 20 00 00 0e 57 8d 00 40 08 00:01:19.662 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 5558 hours (231 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 c0 00 00 06 91 d8 20 40 08 Error: ICRC, ABRT at LBA = 0x0691d820 = 110221344 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 e0 00 c0 00 00 06 91 d8 20 40 08 00:00:26.996 READ FPDMA QUEUED 60 00 88 00 b8 00 00 06 91 e0 d0 40 08 00:00:26.995 READ FPDMA QUEUED 60 00 20 00 b0 00 00 06 91 d8 00 40 08 00:00:26.995 READ FPDMA QUEUED 60 00 48 00 a8 00 00 08 80 24 b8 40 08 00:00:26.992 READ FPDMA QUEUED 60 00 08 00 a0 00 00 08 80 24 b0 40 08 00:00:26.992 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 5497 - # 2 Short offline Completed without error 00% 5496 - # 3 Short offline Completed without error 00% 5269 - # 4 Short offline Completed without error 00% 5183 - # 5 Short offline Completed without error 00% 5065 - # 6 Short offline Completed without error 00% 4830 - # 7 Short offline Completed without error 00% 4660 - # 8 Short offline Completed without error 00% 4452 - # 9 Short offline Completed without error 00% 4058 - #10 Short offline Completed without error 00% 4010 - #11 Short offline Completed without error 00% 3914 - #12 Short offline Completed without error 00% 3848 - #13 Short offline Interrupted (host reset) 00% 3229 - #14 Short offline Completed without error 00% 2988 - #15 Short offline Completed without error 00% 2951 - #16 Short offline Completed without error 00% 2865 - #17 Short offline Completed without error 00% 2865 - #18 Short offline Completed without error 00% 2834 - #19 Short offline Completed without error 00% 2758 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 3 (0x0003) Device State: Active (0) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: 29/42 Celsius Lifetime Min/Max Temperature: 5/57 Celsius Specified Max Operating Temperature: 5 Celsius Under/Over Temperature Limit Count: 0/46 Vendor specific: 00 00 04 00 01 01 00 05 05 00 00 00 00 00 00 00 00 01 00 00 25 fb 33 01 02 02 00 00 00 00 00 05 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/40 Celsius Min/Max Temperature Limit: 0/80 Celsius Temperature History Size (Index): 128 (5) Index Estimated Time Temperature Celsius 6 2023-07-05 09:03 35 **************** 7 2023-07-05 09:04 35 **************** 8 2023-07-05 09:05 34 *************** ... ..( 53 skipped). .. *************** 62 2023-07-05 09:59 34 *************** 63 2023-07-05 10:00 ? - 64 2023-07-05 10:01 32 ************* 65 2023-07-05 10:02 33 ************** 66 2023-07-05 10:03 34 *************** 67 2023-07-05 10:04 34 *************** 68 2023-07-05 10:05 34 *************** 69 2023-07-05 10:06 35 **************** 70 2023-07-05 10:07 35 **************** 71 2023-07-05 10:08 36 ***************** 72 2023-07-05 10:09 36 ***************** 73 2023-07-05 10:10 36 ***************** 74 2023-07-05 10:11 37 ****************** 75 2023-07-05 10:12 37 ****************** 76 2023-07-05 10:13 38 ******************* 77 2023-07-05 10:14 38 ******************* 78 2023-07-05 10:15 38 ******************* 79 2023-07-05 10:16 39 ******************** 80 2023-07-05 10:17 40 ********************* ... ..( 6 skipped). .. ********************* 87 2023-07-05 10:24 40 ********************* 88 2023-07-05 10:25 41 ********************** ... ..( 17 skipped). .. ********************** 106 2023-07-05 10:43 41 ********************** 107 2023-07-05 10:44 42 *********************** 108 2023-07-05 10:45 41 ********************** 109 2023-07-05 10:46 42 *********************** ... ..( 12 skipped). .. *********************** 122 2023-07-05 10:59 42 *********************** 123 2023-07-05 11:00 41 ********************** 124 2023-07-05 11:01 42 *********************** 125 2023-07-05 11:02 42 *********************** 126 2023-07-05 11:03 41 ********************** ... ..( 6 skipped). .. ********************** 5 2023-07-05 11:10 41 ********************** SCT Error Recovery Control: Read: 80 (8.0 seconds) Write: 80 (8.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 10 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-76-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z5K500 Device Model: HGST HTS545050A7E680 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GR2OA3B0 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jul 5 11:10:53 2023 WIB SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 109) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 094 094 062 - 655371 2 Throughput_Performance P-S--- 100 100 040 - 0 3 Spin_Up_Time POS--- 253 253 033 - 0 4 Start_Stop_Count -O--C- 034 034 000 - 104391 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 0 9 Power_On_Hours -O--C- 071 071 000 - 12831 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 9104 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 098 098 000 - 472 193 Load_Cycle_Count -O--C- 062 062 000 - 380007 194 Temperature_Celsius -O---- 166 166 000 - 36 (Min/Max 18/51) 196 Reallocated_Event_Count -O--CK 100 100 000 - 7 197 Current_Pending_Sector -O---K 100 100 000 - 176 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 17406 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 56888 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 56888 [3] occurred at disk power-on lifetime: 12828 hours (534 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 d8 00 00 11 eb 39 18 01 00 Error: UNC at LBA = 0x11eb3918 = 300628248 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 58 00 00 11 eb 3c f0 40 00 00:49:15.359 READ FPDMA QUEUED 60 01 00 00 50 00 00 11 eb 3b f0 40 00 00:49:15.359 READ FPDMA QUEUED 60 01 00 00 48 00 00 11 eb 3a f0 40 00 00:49:15.359 READ FPDMA QUEUED 60 01 00 00 40 00 00 11 eb 39 f0 40 00 00:49:15.359 READ FPDMA QUEUED 60 01 00 00 38 00 00 11 eb 38 f0 40 00 00:49:15.359 READ FPDMA QUEUED Error 56887 [2] occurred at disk power-on lifetime: 12828 hours (534 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 d8 00 00 0d 7e c6 20 0d 00 Error: UNC at LBA = 0x0d7ec620 = 226412064 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 48 00 00 0d 7e c9 f8 40 00 00:49:11.490 READ FPDMA QUEUED 60 01 00 00 40 00 00 0d 7e c8 f8 40 00 00:49:11.490 READ FPDMA QUEUED 60 01 00 00 38 00 00 0d 7e c7 f8 40 00 00:49:11.490 READ FPDMA QUEUED 60 01 00 00 30 00 00 0d 7e c6 f8 40 00 00:49:11.490 READ FPDMA QUEUED 60 01 00 00 28 00 00 0d 7e c5 f8 40 00 00:49:11.490 READ FPDMA QUEUED Error 56886 [1] occurred at disk power-on lifetime: 12828 hours (534 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 a0 00 00 0d c2 76 98 0d 00 Error: WP at LBA = 0x0dc27698 = 230848152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 f8 00 00 00 71 bb b0 40 00 00:49:08.060 WRITE FPDMA QUEUED 60 01 00 00 f0 00 00 0d c2 76 38 40 00 00:49:08.060 READ FPDMA QUEUED 60 01 00 00 e8 00 00 0d c2 75 38 40 00 00:49:08.060 READ FPDMA QUEUED 60 01 00 00 e0 00 00 0d c2 74 38 40 00 00:49:08.060 READ FPDMA QUEUED 60 01 00 00 d8 00 00 0d c2 73 38 40 00 00:49:08.060 READ FPDMA QUEUED Error 56885 [0] occurred at disk power-on lifetime: 12828 hours (534 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 e8 00 00 20 28 ed 98 00 00 Error: UNC at LBA = 0x2028ed98 = 539553176 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 98 00 00 20 28 ef 80 40 00 00:49:04.490 READ FPDMA QUEUED 60 01 00 00 90 00 00 20 28 ee 80 40 00 00:49:04.490 READ FPDMA QUEUED 60 01 00 00 88 00 00 20 28 ed 80 40 00 00:49:04.490 READ FPDMA QUEUED 60 01 00 00 80 00 00 20 28 ec 80 40 00 00:49:04.490 READ FPDMA QUEUED 60 01 00 00 78 00 00 20 28 eb 80 40 00 00:49:04.490 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 80% 12730 120454744 # 2 Short offline Completed without error 00% 12730 - # 3 Short offline Completed without error 00% 12427 - # 4 Short offline Completed without error 00% 12333 - # 5 Short offline Completed without error 00% 12103 - # 6 Short offline Completed without error 00% 11939 - # 7 Short offline Completed without error 00% 11738 - # 8 Short offline Completed without error 00% 11351 - # 9 Short offline Completed without error 00% 11303 - #10 Short offline Completed without error 00% 11207 - #11 Short offline Completed without error 00% 11142 - #12 Short offline Interrupted (host reset) 90% 10524 - #13 Short offline Completed without error 00% 10283 - #14 Short offline Completed without error 00% 10246 - #15 Short offline Completed without error 00% 10165 - #16 Short offline Completed without error 00% 10165 - #17 Short offline Aborted by host 90% 7288 - #18 Short offline Completed without error 00% 290 - #19 Short offline Completed without error 00% 245 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 28/36 Celsius Lifetime Min/Max Temperature: 18/51 Celsius Specified Max Operating Temperature: 35 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (53) Index Estimated Time Temperature Celsius 54 2023-07-05 09:03 31 ************ ... ..( 49 skipped). .. ************ 104 2023-07-05 09:53 31 ************ 105 2023-07-05 09:54 32 ************* 106 2023-07-05 09:55 31 ************ ... ..( 2 skipped). .. ************ 109 2023-07-05 09:58 31 ************ 110 2023-07-05 09:59 ? - 111 2023-07-05 10:00 29 ********** 112 2023-07-05 10:01 29 ********** 113 2023-07-05 10:02 29 ********** 114 2023-07-05 10:03 30 *********** 115 2023-07-05 10:04 30 *********** 116 2023-07-05 10:05 30 *********** 117 2023-07-05 10:06 31 ************ 118 2023-07-05 10:07 31 ************ 119 2023-07-05 10:08 31 ************ 120 2023-07-05 10:09 32 ************* ... ..( 2 skipped). .. ************* 123 2023-07-05 10:12 32 ************* 124 2023-07-05 10:13 33 ************** ... ..( 2 skipped). .. ************** 127 2023-07-05 10:16 33 ************** 0 2023-07-05 10:17 34 *************** ... ..( 4 skipped). .. *************** 5 2023-07-05 10:22 34 *************** 6 2023-07-05 10:23 35 **************** ... ..( 10 skipped). .. **************** 17 2023-07-05 10:34 35 **************** 18 2023-07-05 10:35 36 ***************** ... ..( 34 skipped). .. ***************** 53 2023-07-05 11:10 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-76-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: OM600 Serial Number: -- Firmware Version: U0524A0 User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: mSATA TRIM Command: Available Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jul 5 11:10:54 2023 WIB SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0 9 Power_On_Hours -O--CK 100 100 050 - 814 12 Power_Cycle_Count -O--CK 100 100 050 - 559 160 Unknown_Attribute -O--CK 100 100 050 - 0 161 Unknown_Attribute PO--CK 100 100 050 - 100 163 Unknown_Attribute -O--CK 100 100 050 - 23 164 Unknown_Attribute -O--CK 100 100 050 - 17070 165 Unknown_Attribute -O--CK 100 100 050 - 81 166 Unknown_Attribute -O--CK 100 100 050 - 15 167 Unknown_Attribute -O--CK 100 100 050 - 54 168 Unknown_Attribute -O--CK 100 100 050 - 5050 169 Unknown_Attribute -O--CK 100 100 050 - 99 175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 0 177 Wear_Leveling_Count -O--CK 100 100 050 - 0 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0 192 Power-Off_Retract_Count -O--CK 100 100 050 - 145 194 Temperature_Celsius -O---K 100 100 050 - 40 195 Hardware_ECC_Recovered -O--CK 100 100 050 - 0 196 Reallocated_Event_Count -O--CK 100 100 050 - 0 197 Current_Pending_Sector -O--CK 100 100 050 - 0 198 Offline_Uncorrectable -O--CK 100 100 050 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 18651 232 Available_Reservd_Space -O--CK 100 100 050 - 100 241 Total_LBAs_Written ----CK 100 100 050 - 86847 242 Total_LBAs_Read ----CK 100 100 050 - 72733 245 Unknown_Attribute -O--CK 100 100 050 - 69785 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 32 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 18651 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 18651 [2] log entry is empty Error 18650 [1] log entry is empty Error 18649 [0] log entry is empty Error 18648 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 01 01 00 00 00 00 00 00 40 08 00:00:00.000 IDENTIFY DEVICE b0 00 d0 01 01 00 00 4f 00 c2 00 00 08 00:00:00.000 SMART READ DATA ec 00 00 01 01 00 00 00 00 00 00 00 08 00:00:00.000 IDENTIFY DEVICE ec 00 00 01 01 00 00 00 00 00 00 00 08 00:00:00.000 IDENTIFY DEVICE 2f 00 00 01 01 00 00 00 00 00 00 e0 08 00:00:00.000 READ LOG EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 729 - # 2 Extended offline Self-test routine in progress 70% 729 - # 3 Short offline Completed without error 00% 729 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 559 --- Lifetime Power-On Resets 0x01 0x010 4 814 --- Power-on Hours 0x01 0x018 6 1396651697 --- Logical Sectors Written 0x01 0x020 6 53128452 --- Number of Write Commands 0x01 0x028 6 471687073 --- Logical Sectors Read 0x01 0x030 6 59020952 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 10 Device-to-host register FISes sent due to a COMRESET