/dev/nvme0n1 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.6.0-1-amd64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: KINGSTON RBUSNS8154P3128GJ1 Serial Number: -- Firmware Version: E8FK12.3 PCI Vendor/Subsystem ID: 0x2646 IEEE OUI Identifier: 0x0026b7 Total NVM Capacity: 128,035,676,160 [128 GB] Unallocated NVM Capacity: 0 Controller ID: 0 Number of Namespaces: 1 Namespace 1 Size/Capacity: 128,035,676,160 [128 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 0026b7 ... Local Time is: Fri May 22 23:22:47 2020 EDT Firmware Updates (0x12): 1 Slot, no Reset required Optional Admin Commands (0x0007): Security Format Frmw_DL Optional NVM Commands (0x001e): Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Maximum Data Transfer Size: 512 Pages Warning Comp. Temp. Threshold: 84 Celsius Critical Comp. Temp. Threshold: 88 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 7.90W 0.0790W - 0 0 0 0 600 600 1 + 7.90W 0.0790W - 0 0 0 0 600 600 2 + 7.90W 0.0790W - 0 0 0 0 600 600 3 - 0.1000W 0.0790W - 3 3 3 3 1000 1000 4 - 0.0050W 0.0790W - 4 4 4 4 400000 90000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 1 1 - 4096 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 29 Celsius Available Spare: 100% Available Spare Threshold: 100% Percentage Used: 0% Data Units Read: 506,559 [259 GB] Data Units Written: 452,696 [231 GB] Host Read Commands: 4,747,385 Host Write Commands: 3,776,626 Controller Busy Time: 11 Power Cycles: 93 Power On Hours: 11 Unsafe Shutdowns: 3 Media and Data Integrity Errors: 0 Error Information Log Entries: 129 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 2: 29 Celsius Error Information (NVMe Log 0x01, max 16 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS 0 129 0 0x000a 0x0004 - 4009754624 1 - 1 128 0 0x000a 0x0004 - 4009754624 1 - 2 127 0 0x000a 0x0004 - 4009754624 1 - 3 126 0 0x000a 0x0004 - 4009754624 1 - 4 125 0 0x000a 0x0004 - 4009754624 1 - 5 124 0 0x000a 0x0004 - 4009754624 1 - 6 123 0 0x000a 0x0004 - 4009754624 1 - 7 122 0 0x000a 0x0004 - 4009754624 1 - 8 121 0 0x000a 0x0004 - 4009754624 1 - 9 120 0 0x000a 0x0004 - 4009754624 1 - 10 119 0 0x0005 0x0016 - 196611 0 - 11 118 0 0x0002 0x0017 - 196611 0 - 12 117 0 0x0001 0x0017 - 196611 0 - 13 116 0 0x001b 0x0005 - 4009754624 1 - 14 115 0 0x0005 0x0016 - 196611 0 - 15 114 0 0x0002 0x0017 - 196611 0 - /dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.6.0-1-amd64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10SPZX-21Z10T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.01A02 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri May 22 23:22:47 2020 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 540) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 67) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 195 190 021 - 1250 4 Start_Stop_Count -O--CK 100 100 000 - 242 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 185 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 80 191 G-Sense_Error_Rate -O--CK 001 001 000 - 605 192 Power-Off_Retract_Count -O--CK 200 200 000 - 19 193 Load_Cycle_Count -O--CK 200 200 000 - 489 194 Temperature_Celsius -O---K 105 098 000 - 38 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 288 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 74 Device vendor specific log 0xb9 GPL,SL VS 4 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 21/38 Celsius Lifetime Min/Max Temperature: 18/45 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (124) Index Estimated Time Temperature Celsius 125 2020-05-22 21:15 36 ***************** 126 2020-05-22 21:16 36 ***************** 127 2020-05-22 21:17 36 ***************** 0 2020-05-22 21:18 37 ****************** ... ..( 6 skipped). .. ****************** 7 2020-05-22 21:25 37 ****************** 8 2020-05-22 21:26 38 ******************* ... ..( 9 skipped). .. ******************* 18 2020-05-22 21:36 38 ******************* 19 2020-05-22 21:37 37 ****************** ... ..( 27 skipped). .. ****************** 47 2020-05-22 22:05 37 ****************** 48 2020-05-22 22:06 38 ******************* ... ..( 20 skipped). .. ******************* 69 2020-05-22 22:27 38 ******************* 70 2020-05-22 22:28 37 ****************** ... ..( 45 skipped). .. ****************** 116 2020-05-22 23:14 37 ****************** 117 2020-05-22 23:15 38 ******************* ... ..( 6 skipped). .. ******************* 124 2020-05-22 23:22 38 ******************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 55397 Vendor specific