/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.8-200.fc37.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SandForce Driven SSDs Device Model: SanDisk SDSSDA120G Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: Z22000RL User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 1.8 inches TRIM Command: Available Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Feb 7 14:51:43 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Disabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Retired_Block_Count -O--CK 100 100 000 - 0 9 Power_On_Hours_and_Msec -O--CK 090 100 000 - 3674h+00m+00.000s 12 Power_Cycle_Count -O--CK 100 100 000 - 9638 166 Unknown_Attribute -O--CK 100 100 000 - 7553 167 Unknown_Attribute -O--CK 100 100 000 - 0 168 Unknown_Attribute -O--CK 100 100 000 - 7609 169 Unknown_Attribute -O--CK 100 100 000 - 13 170 Reserve_Block_Count -O--CK 100 100 000 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Unknown_SandForce_Attr -O--CK 100 100 --- - 7552 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 8291 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 072 100 000 - 28 (Min/Max 0/52) 199 SATA_CRC_Error_Count -O--CK 100 100 000 - 15 230 Life_Curve_Status -O--CK 100 100 000 - 252 232 Available_Reservd_Space PO--CK 100 100 004 - 100 233 SandForce_Internal -O--CK 100 100 000 - 704292 241 Lifetime_Writes_GiB ----CK 253 253 000 - 11914 242 Lifetime_Reads_GiB ----CK 253 253 000 - 14118 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 15 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 15 [2] log entry is empty Error 14 [1] log entry is empty Error 13 [0] log entry is empty Error 12 [3] log entry is empty SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 9638 --- Lifetime Power-On Resets 0x01 0x010 4 3674 --- Power-on Hours 0x01 0x018 6 11914 --- Logical Sectors Written 0x01 0x020 6 542258284 --- Number of Write Commands 0x01 0x028 6 14118 --- Logical Sectors Read 0x01 0x030 6 592312029 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (empty) == 0x03 ===== = = === == Rotating Media Statistics (empty) == 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 8307 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 28 --- Current Temperature 0x05 0x010 1 -18 --- Average Short Term Temperature 0x05 0x018 1 121 --- Average Long Term Temperature 0x05 0x020 1 51 --- Highest Temperature 0x05 0x028 1 8 --- Lowest Temperature 0x05 0x030 1 -1 --- Highest Average Short Term Temperature 0x05 0x038 1 0 --- Lowest Average Short Term Temperature 0x05 0x040 1 -1 --- Highest Average Long Term Temperature 0x05 0x048 1 0 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 100 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 11806 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 251 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.8-200.fc37.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD3200BEVS-08VAT2 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 14.01A14 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 1.5 Gb/s Local Time is: Tue Feb 7 14:51:43 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9960) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 118) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 186 184 021 - 1666 4 Start_Stop_Count -O--CK 073 073 000 - 27666 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 100 253 051 - 0 9 Power_On_Hours -O--CK 036 036 000 - 46794 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 090 090 000 - 10949 192 Power-Off_Retract_Count -O--CK 192 192 000 - 6527 193 Load_Cycle_Count -O--CK 007 007 000 - 581799 194 Temperature_Celsius -O---K 119 067 000 - 28 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 240 Head_Flying_Hours -O--CK 080 080 000 - 14802 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 222 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 222 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 9b 25 17 3e 00 00 00 00 00 00 00 21 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 17 9b 00 3e 27 00 00 08 00:00:57.352 DEVICE RESET 00 8c ef 17 3e 00 00 08 00 00 00 00 00 00:25:23.346 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 17 8c 00 3e 27 00 00 08 00:00:00.070 DEVICE RESET Error 221 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 f8 25 17 32 00 00 00 00 00 00 00 21 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 17 f8 00 32 27 00 00 08 00:00:57.352 DEVICE RESET 00 e9 ef 17 32 00 00 08 00 00 00 00 00 00:25:20.367 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 17 e9 00 32 27 00 00 08 00:00:00.070 DEVICE RESET Error 220 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 b4 25 17 26 00 00 00 00 00 00 00 21 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 17 b3 00 26 27 00 00 08 00:00:57.352 DEVICE RESET 00 a5 ef 17 26 00 00 08 00 00 00 00 00 00:25:17.227 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 17 a5 00 26 27 00 00 08 00:00:00.070 DEVICE RESET Error 219 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 01 25 17 1b 00 00 00 00 00 00 00 21 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 17 01 00 1b 27 00 00 08 00:00:57.352 DEVICE RESET 00 f2 ef 17 1a 00 00 08 00 00 00 00 00 00:25:14.232 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 17 f2 00 1a 27 00 00 08 00:00:00.070 DEVICE RESET Error 218 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c1 25 17 0e 00 00 00 00 00 00 00 21 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 17 c0 00 0e 27 00 00 08 00:00:57.352 DEVICE RESET 00 b2 ef 17 0e 00 00 08 00 00 00 00 00 00:25:11.096 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 17 b2 00 0e 27 00 00 08 00:00:00.070 DEVICE RESET Error 217 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 1b 25 17 03 00 00 00 00 00 00 00 21 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 08 00 00 48 17 1b 22 03 35 00 00 08 00:00:57.352 DEVICE RESET 19 1a 35 17 03 00 08 08 00 00 00 00 1f 00:25:08.123 RECALIBRATE [RET-4] 08 08 00 00 10 17 1a 21 03 35 00 00 08 00:00:06.200 DEVICE RESET Error 216 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 72 25 16 f7 00 00 00 00 00 00 00 21 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 16 72 00 f7 27 00 00 08 00:00:57.352 DEVICE RESET 00 63 ef 16 f7 00 00 08 00 00 00 00 00 00:25:05.129 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 16 63 00 f7 27 00 00 08 00:00:00.070 DEVICE RESET Error 215 [22] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 3e 25 16 eb 00 00 00 00 00 00 00 21 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 16 3e 00 eb 27 00 00 08 00:00:57.352 DEVICE RESET 00 2e ef 16 eb 00 00 08 00 00 00 00 00 00:25:02.006 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 16 2e 00 eb 27 00 00 08 00:00:00.070 DEVICE RESET SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5851 - # 2 Short offline Completed without error 00% 5288 - # 3 Short offline Completed without error 00% 5069 - # 4 Short offline Completed without error 00% 4866 - # 5 Short offline Completed without error 00% 4613 - # 6 Short offline Completed: read failure 90% 4039 558718435 # 7 Short offline Completed without error 00% 3797 - # 8 Short offline Completed without error 00% 414 - # 9 Vendor (0x50) Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 27/32 Celsius Lifetime Min/Max Temperature: 27/80 Celsius Specified Max Operating Temperature: 32 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (17) Index Estimated Time Temperature Celsius 18 2023-02-07 12:44 32 ************* 19 2023-02-07 12:45 34 *************** 20 2023-02-07 12:46 35 **************** 21 2023-02-07 12:47 35 **************** 22 2023-02-07 12:48 34 *************** 23 2023-02-07 12:49 34 *************** 24 2023-02-07 12:50 33 ************** 25 2023-02-07 12:51 ? - 26 2023-02-07 12:52 29 ********** ... ..( 2 skipped). .. ********** 29 2023-02-07 12:55 29 ********** 30 2023-02-07 12:56 30 *********** 31 2023-02-07 12:57 31 ************ ... ..( 2 skipped). .. ************ 34 2023-02-07 13:00 31 ************ 35 2023-02-07 13:01 32 ************* 36 2023-02-07 13:02 31 ************ 37 2023-02-07 13:03 31 ************ 38 2023-02-07 13:04 31 ************ 39 2023-02-07 13:05 30 *********** 40 2023-02-07 13:06 29 ********** ... ..( 6 skipped). .. ********** 47 2023-02-07 13:13 29 ********** 48 2023-02-07 13:14 28 ********* ... ..( 4 skipped). .. ********* 53 2023-02-07 13:19 28 ********* 54 2023-02-07 13:20 27 ******** ... ..( 29 skipped). .. ******** 84 2023-02-07 13:50 27 ******** 85 2023-02-07 13:51 28 ********* ... ..( 5 skipped). .. ********* 91 2023-02-07 13:57 28 ********* 92 2023-02-07 13:58 27 ******** ... ..( 19 skipped). .. ******** 112 2023-02-07 14:18 27 ******** 113 2023-02-07 14:19 28 ********* ... ..( 9 skipped). .. ********* 123 2023-02-07 14:29 28 ********* 124 2023-02-07 14:30 27 ******** 125 2023-02-07 14:31 27 ******** 126 2023-02-07 14:32 28 ********* ... ..( 3 skipped). .. ********* 2 2023-02-07 14:36 28 ********* 3 2023-02-07 14:37 27 ******** ... ..( 13 skipped). .. ******** 17 2023-02-07 14:51 27 ******** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 7195 Vendor specific