/dev/nvme0n1 === START OF INFORMATION SECTION === Model Number: Samsung SSD 960 EVO 250GB Serial Number: -- Firmware Version: 3B7QCXE7 PCI Vendor/Subsystem ID: 0x144d IEEE OUI Identifier: 0x002538 Total NVM Capacity: 250,059,350,016 [250 GB] Unallocated NVM Capacity: 0 Controller ID: 2 Number of Namespaces: 1 Namespace 1 Size/Capacity: 250,059,350,016 [250 GB] Namespace 1 Utilization: 28,670,054,400 [28.6 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 002538 ... Local Time is: Mon Jul 9 21:38:23 2018 MSK Firmware Updates (0x16): 3 Slots, no Reset required Optional Admin Commands (0x0007): Security Format Frmw_DL Optional NVM Commands (0x001f): Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Maximum Data Transfer Size: 512 Pages Warning Comp. Temp. Threshold: 77 Celsius Critical Comp. Temp. Threshold: 79 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 6.04W - - 0 0 0 0 0 0 1 + 5.09W - - 1 1 1 1 0 0 2 + 4.08W - - 2 2 2 2 0 0 3 - 0.0400W - - 3 3 3 3 210 1500 4 - 0.0050W - - 4 4 4 4 2200 6000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02, NSID 0x1) Critical Warning: 0x00 Temperature: 38 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 5% Data Units Read: 47,987,439 [24.5 TB] Data Units Written: 27,414,247 [14.0 TB] Host Read Commands: 466,734,786 Host Write Commands: 243,005,742 Controller Busy Time: 1,400 Power Cycles: 2,054 Power On Hours: 830 Unsafe Shutdowns: 1,006 Media and Data Integrity Errors: 0 Error Information Log Entries: 14,850 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 38 Celsius Temperature Sensor 2: 55 Celsius Error Information (NVMe Log 0x01, max 64 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS 0 14850 0 0x0074 0x4212 0x028 0 0 - 1 14849 0 0x0068 0x4212 0x028 0 0 - 2 14848 0 0x0049 0x4212 0x028 0 0 - 3 14847 0 0x0042 0x4212 0x028 0 0 - 4 14846 0 0x0077 0x4212 0x028 0 0 - 5 14845 0 0x004c 0x4212 0x028 0 0 - 6 14844 1 - 0x0000 0x000 0 0 - 7 14843 0 0x0051 0x4212 0x028 0 0 - 8 14842 1 - 0x0000 0x000 0 0 - 9 14841 1 0x0000 0x4016 0x004 0 0 - 10 14840 1 - 0x0000 0x000 0 0 - 11 14839 0 0x007c 0x4212 0x028 0 0 - 12 14838 0 0x005c 0x4212 0x028 0 0 - 13 14837 0 0x002d 0x4212 0x028 0 0 - 14 14836 0 0x0077 0x4212 0x028 0 0 - 15 14835 0 0x007e 0x4212 0x028 0 0 - ... (48 entries not shown) /dev/sda === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" MG04ACA... Enterprise HDD Device Model: TOSHIBA MG04ACA200E Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: FP3B User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jul 9 21:38:23 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 242) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 2345 4 Start_Stop_Count -O--CK 100 100 000 - 727 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 8 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 099 099 000 - 675 10 Spin_Retry_Count PO--CK 114 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 700 191 G-Sense_Error_Rate -O--CK 100 100 000 - 6 192 Power-Off_Retract_Count -O--CK 100 100 000 - 366 193 Load_Cycle_Count -O--CK 100 100 000 - 760 194 Temperature_Celsius -O---K 100 100 000 - 44 (Min/Max 21/56) 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 253 000 - 0 220 Disk_Shift -O---- 100 100 000 - 0 222 Loaded_Hours -O--CK 099 099 000 - 667 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 535 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 12288 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa7 GPL VS 8 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 15 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 15 [14] occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 01 00 00 00 00 00 00 40 00 00:12:58.402 SECURITY UNLOCK f6 00 00 00 01 00 00 00 00 00 00 40 00 00:12:27.836 SECURITY DISABLE PASSWORD f2 00 00 00 01 00 00 00 00 00 00 40 00 00:12:27.769 SECURITY UNLOCK b0 00 da 00 00 00 00 00 c2 4f 00 00 00 00:11:34.425 SMART RETURN STATUS b0 00 d0 00 01 00 00 00 c2 4f 00 00 00 00:11:34.301 SMART READ DATA Error 14 [13] occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 01 00 00 00 00 00 00 40 00 00:12:27.769 SECURITY UNLOCK b0 00 da 00 00 00 00 00 c2 4f 00 00 00 00:11:34.425 SMART RETURN STATUS b0 00 d0 00 01 00 00 00 c2 4f 00 00 00 00:11:34.301 SMART READ DATA b0 00 d1 00 01 00 00 00 c2 4f 00 00 00 00:11:34.300 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] ec 00 00 00 01 00 00 00 00 00 00 00 00 00:11:34.300 IDENTIFY DEVICE Error 13 [12] occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 01 00 00 00 00 00 00 40 00 00:07:06.690 SECURITY UNLOCK ec 00 00 00 01 00 00 00 00 00 00 40 00 00:02:45.071 IDENTIFY DEVICE b0 00 da 00 00 00 00 00 c2 4f 00 00 00 00:01:33.770 SMART RETURN STATUS b0 00 d0 00 01 00 00 00 c2 4f 00 00 00 00:01:33.638 SMART READ DATA b0 00 d1 00 01 00 00 00 c2 4f 00 00 00 00:01:33.637 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] Error 12 [11] occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 01 00 00 00 00 00 00 40 00 00:06:02.373 SECURITY UNLOCK ec 00 00 00 00 00 00 00 00 00 00 00 00 00:06:02.373 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:06:02.074 IDENTIFY DEVICE f2 00 00 00 01 00 00 00 00 00 00 40 00 00:06:02.014 SECURITY UNLOCK ec 00 00 00 00 00 00 00 00 00 00 00 00 00:06:02.013 IDENTIFY DEVICE Error 11 [10] occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 01 00 00 00 00 00 00 40 00 00:06:02.014 SECURITY UNLOCK ec 00 00 00 00 00 00 00 00 00 00 00 00 00:06:02.013 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:05:51.501 IDENTIFY DEVICE b0 00 da 00 00 00 00 00 c2 4f 00 00 00 00:05:51.251 SMART RETURN STATUS b0 00 d2 00 f1 00 00 00 c2 4f 00 00 00 00:05:51.250 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE Error 10 [9] occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 01 00 00 00 00 00 00 40 00 00:01:01.356 SECURITY UNLOCK ec 00 00 00 00 00 00 00 00 00 00 00 00 00:01:01.355 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:01:00.984 IDENTIFY DEVICE f2 00 00 00 01 00 00 00 00 00 00 40 00 00:01:00.948 SECURITY UNLOCK ec 00 00 00 00 00 00 00 00 00 00 00 00 00:01:00.947 IDENTIFY DEVICE Error 9 [8] occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 01 00 00 00 00 00 00 40 00 00:01:00.948 SECURITY UNLOCK ec 00 00 00 00 00 00 00 00 00 00 00 00 00:01:00.947 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:01:00.634 IDENTIFY DEVICE f2 00 00 00 01 00 00 00 00 00 00 40 00 00:01:00.573 SECURITY UNLOCK ec 00 00 00 00 00 00 00 00 00 00 00 00 00:01:00.572 IDENTIFY DEVICE Error 8 [7] occurred at disk power-on lifetime: 42 hours (1 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f2 00 00 00 01 00 00 00 00 00 00 40 00 00:01:00.573 SECURITY UNLOCK ec 00 00 00 00 00 00 00 00 00 00 00 00 00:01:00.572 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:14.035 IDENTIFY DEVICE b0 00 da 00 00 00 00 00 c2 4f 00 00 00 00:00:13.903 SMART RETURN STATUS b0 00 d2 00 f1 00 00 00 c2 4f 00 00 00 00:00:13.902 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 44 Celsius Power Cycle Min/Max Temperature: 43/46 Celsius Lifetime Min/Max Temperature: 21/56 Celsius Under/Over Temperature Limit Count: 0/15 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: 5/55 Celsius Temperature History Size (Index): 478 (6) Index Estimated Time Temperature Celsius 7 2018-07-09 13:41 43 ************************ 8 2018-07-09 13:42 43 ************************ 9 2018-07-09 13:43 42 *********************** 10 2018-07-09 13:44 43 ************************ ... ..( 18 skipped). .. ************************ 29 2018-07-09 14:03 43 ************************ 30 2018-07-09 14:04 42 *********************** 31 2018-07-09 14:05 43 ************************ 32 2018-07-09 14:06 ? - 33 2018-07-09 14:07 30 *********** 34 2018-07-09 14:08 30 *********** 35 2018-07-09 14:09 31 ************ 36 2018-07-09 14:10 31 ************ 37 2018-07-09 14:11 31 ************ 38 2018-07-09 14:12 ? - 39 2018-07-09 14:13 42 *********************** 40 2018-07-09 14:14 42 *********************** 41 2018-07-09 14:15 42 *********************** 42 2018-07-09 14:16 ? - 43 2018-07-09 14:17 28 ********* 44 2018-07-09 14:18 29 ********** 45 2018-07-09 14:19 29 ********** 46 2018-07-09 14:20 30 *********** 47 2018-07-09 14:21 30 *********** 48 2018-07-09 14:22 30 *********** 49 2018-07-09 14:23 31 ************ 50 2018-07-09 14:24 31 ************ 51 2018-07-09 14:25 ? - 52 2018-07-09 14:26 31 ************ 53 2018-07-09 14:27 31 ************ 54 2018-07-09 14:28 36 ***************** 55 2018-07-09 14:29 36 ***************** 56 2018-07-09 14:30 36 ***************** 57 2018-07-09 14:31 39 ******************** 58 2018-07-09 14:32 39 ******************** 59 2018-07-09 14:33 39 ******************** 60 2018-07-09 14:34 41 ********************** 61 2018-07-09 14:35 41 ********************** 62 2018-07-09 14:36 41 ********************** 63 2018-07-09 14:37 42 *********************** 64 2018-07-09 14:38 42 *********************** 65 2018-07-09 14:39 42 *********************** 66 2018-07-09 14:40 ? - 67 2018-07-09 14:41 29 ********** 68 2018-07-09 14:42 29 ********** 69 2018-07-09 14:43 30 *********** 70 2018-07-09 14:44 30 *********** 71 2018-07-09 14:45 31 ************ 72 2018-07-09 14:46 31 ************ 73 2018-07-09 14:47 31 ************ 74 2018-07-09 14:48 32 ************* 75 2018-07-09 14:49 32 ************* 76 2018-07-09 14:50 32 ************* 77 2018-07-09 14:51 33 ************** 78 2018-07-09 14:52 33 ************** 79 2018-07-09 14:53 33 ************** 80 2018-07-09 14:54 34 *************** 81 2018-07-09 14:55 34 *************** 82 2018-07-09 14:56 34 *************** 83 2018-07-09 14:57 35 **************** 84 2018-07-09 14:58 35 **************** 85 2018-07-09 14:59 35 **************** 86 2018-07-09 15:00 36 ***************** ... ..( 5 skipped). .. ***************** 92 2018-07-09 15:06 36 ***************** 93 2018-07-09 15:07 37 ****************** ... ..( 4 skipped). .. ****************** 98 2018-07-09 15:12 37 ****************** 99 2018-07-09 15:13 38 ******************* ... ..( 6 skipped). .. ******************* 106 2018-07-09 15:20 38 ******************* 107 2018-07-09 15:21 39 ******************** ... ..( 6 skipped). .. ******************** 114 2018-07-09 15:28 39 ******************** 115 2018-07-09 15:29 40 ********************* ... ..( 8 skipped). .. ********************* 124 2018-07-09 15:38 40 ********************* 125 2018-07-09 15:39 41 ********************** ... ..( 11 skipped). .. ********************** 137 2018-07-09 15:51 41 ********************** 138 2018-07-09 15:52 42 *********************** 139 2018-07-09 15:53 41 ********************** 140 2018-07-09 15:54 42 *********************** ... ..( 42 skipped). .. *********************** 183 2018-07-09 16:37 42 *********************** 184 2018-07-09 16:38 43 ************************ 185 2018-07-09 16:39 42 *********************** 186 2018-07-09 16:40 42 *********************** 187 2018-07-09 16:41 43 ************************ ... ..( 73 skipped). .. ************************ 261 2018-07-09 17:55 43 ************************ 262 2018-07-09 17:56 ? - 263 2018-07-09 17:57 28 ********* 264 2018-07-09 17:58 28 ********* 265 2018-07-09 17:59 29 ********** 266 2018-07-09 18:00 30 *********** 267 2018-07-09 18:01 30 *********** 268 2018-07-09 18:02 31 ************ ... ..( 2 skipped). .. ************ 271 2018-07-09 18:05 31 ************ 272 2018-07-09 18:06 32 ************* 273 2018-07-09 18:07 32 ************* 274 2018-07-09 18:08 32 ************* 275 2018-07-09 18:09 33 ************** 276 2018-07-09 18:10 33 ************** 277 2018-07-09 18:11 33 ************** 278 2018-07-09 18:12 34 *************** 279 2018-07-09 18:13 34 *************** 280 2018-07-09 18:14 35 **************** ... ..( 3 skipped). .. **************** 284 2018-07-09 18:18 35 **************** 285 2018-07-09 18:19 36 ***************** ... ..( 5 skipped). .. ***************** 291 2018-07-09 18:25 36 ***************** 292 2018-07-09 18:26 37 ****************** ... ..( 4 skipped). .. ****************** 297 2018-07-09 18:31 37 ****************** 298 2018-07-09 18:32 38 ******************* ... ..( 6 skipped). .. ******************* 305 2018-07-09 18:39 38 ******************* 306 2018-07-09 18:40 39 ******************** ... ..( 7 skipped). .. ******************** 314 2018-07-09 18:48 39 ******************** 315 2018-07-09 18:49 40 ********************* ... ..( 15 skipped). .. ********************* 331 2018-07-09 19:05 40 ********************* 332 2018-07-09 19:06 41 ********************** ... ..( 46 skipped). .. ********************** 379 2018-07-09 19:53 41 ********************** 380 2018-07-09 19:54 42 *********************** 381 2018-07-09 19:55 41 ********************** 382 2018-07-09 19:56 41 ********************** 383 2018-07-09 19:57 41 ********************** 384 2018-07-09 19:58 42 *********************** 385 2018-07-09 19:59 42 *********************** 386 2018-07-09 20:00 41 ********************** 387 2018-07-09 20:01 42 *********************** ... ..( 2 skipped). .. *********************** 390 2018-07-09 20:04 42 *********************** 391 2018-07-09 20:05 41 ********************** 392 2018-07-09 20:06 ? - 393 2018-07-09 20:07 43 ************************ ... ..( 7 skipped). .. ************************ 401 2018-07-09 20:15 43 ************************ 402 2018-07-09 20:16 46 *************************** 403 2018-07-09 20:17 45 ************************** ... ..( 4 skipped). .. ************************** 408 2018-07-09 20:22 45 ************************** 409 2018-07-09 20:23 44 ************************* 410 2018-07-09 20:24 44 ************************* 411 2018-07-09 20:25 45 ************************** 412 2018-07-09 20:26 45 ************************** 413 2018-07-09 20:27 45 ************************** 414 2018-07-09 20:28 46 *************************** 415 2018-07-09 20:29 46 *************************** 416 2018-07-09 20:30 45 ************************** 417 2018-07-09 20:31 46 *************************** 418 2018-07-09 20:32 46 *************************** 419 2018-07-09 20:33 45 ************************** ... ..( 13 skipped). .. ************************** 433 2018-07-09 20:47 45 ************************** 434 2018-07-09 20:48 44 ************************* 435 2018-07-09 20:49 45 ************************** 436 2018-07-09 20:50 45 ************************** 437 2018-07-09 20:51 44 ************************* 438 2018-07-09 20:52 45 ************************** 439 2018-07-09 20:53 45 ************************** 440 2018-07-09 20:54 44 ************************* ... ..( 10 skipped). .. ************************* 451 2018-07-09 21:05 44 ************************* 452 2018-07-09 21:06 43 ************************ ... ..( 7 skipped). .. ************************ 460 2018-07-09 21:14 43 ************************ 461 2018-07-09 21:15 44 ************************* 462 2018-07-09 21:16 44 ************************* 463 2018-07-09 21:17 44 ************************* 464 2018-07-09 21:18 43 ************************ 465 2018-07-09 21:19 43 ************************ 466 2018-07-09 21:20 43 ************************ 467 2018-07-09 21:21 44 ************************* 468 2018-07-09 21:22 44 ************************* 469 2018-07-09 21:23 43 ************************ 470 2018-07-09 21:24 44 ************************* ... ..( 7 skipped). .. ************************* 0 2018-07-09 21:32 44 ************************* 1 2018-07-09 21:33 43 ************************ ... ..( 3 skipped). .. ************************ 5 2018-07-09 21:37 43 ************************ 6 2018-07-09 21:38 44 ************************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 700 --- Lifetime Power-On Resets 0x01 0x010 4 675 --- Power-on Hours 0x01 0x018 6 8251985877 --- Logical Sectors Written 0x01 0x020 6 36380232 --- Number of Write Commands 0x01 0x028 6 4347845399 --- Logical Sectors Read 0x01 0x030 6 26396854 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 6 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 671 --- Spindle Motor Power-on Hours 0x03 0x010 4 667 --- Head Flying Hours 0x03 0x018 4 760 --- Head Load Events 0x03 0x020 4 8 --- Number of Reallocated Logical Sectors 0x03 0x028 4 1 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 4 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 44 --- Current Temperature 0x05 0x010 1 40 N-- Average Short Term Temperature 0x05 0x018 1 - N-- Average Long Term Temperature 0x05 0x020 1 56 --- Highest Temperature 0x05 0x028 1 21 --- Lowest Temperature 0x05 0x030 1 42 N-- Highest Average Short Term Temperature 0x05 0x038 1 34 N-- Lowest Average Short Term Temperature 0x05 0x040 1 - N-- Highest Average Long Term Temperature 0x05 0x048 1 - N-- Lowest Average Long Term Temperature 0x05 0x050 4 26 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 3864 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 50 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 49 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 850 PRO 256GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EXM04B6Q User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jul 9 21:38:25 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 133) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 099 099 000 - 755 12 Power_Cycle_Count -O--CK 099 099 000 - 815 177 Wear_Leveling_Count PO--C- 099 099 000 - 6 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 099 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 070 050 000 - 30 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 099 099 000 - 7 235 POR_Recovery_Count -O--C- 099 099 000 - 437 241 Total_LBAs_Written -O--CK 099 099 000 - 3080935590 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: ?/31 Celsius Lifetime Min/Max Temperature: 23/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (50) Index Estimated Time Temperature Celsius 51 2018-07-09 00:20 29 ********** 52 2018-07-09 00:30 30 *********** 53 2018-07-09 00:40 31 ************ ... ..( 14 skipped). .. ************ 68 2018-07-09 03:10 31 ************ 69 2018-07-09 03:20 ? - 70 2018-07-09 03:30 27 ******** 71 2018-07-09 03:40 29 ********** 72 2018-07-09 03:50 30 *********** 73 2018-07-09 04:00 30 *********** 74 2018-07-09 04:10 31 ************ 75 2018-07-09 04:20 30 *********** 76 2018-07-09 04:30 30 *********** 77 2018-07-09 04:40 31 ************ ... ..( 9 skipped). .. ************ 87 2018-07-09 06:20 31 ************ 88 2018-07-09 06:30 32 ************* 89 2018-07-09 06:40 32 ************* 90 2018-07-09 06:50 32 ************* 91 2018-07-09 07:00 31 ************ 92 2018-07-09 07:10 32 ************* 93 2018-07-09 07:20 ? - ... ..( 6 skipped). .. - 100 2018-07-09 08:30 ? - 101 2018-07-09 08:40 28 ********* 102 2018-07-09 08:50 29 ********** 103 2018-07-09 09:00 29 ********** 104 2018-07-09 09:10 29 ********** 105 2018-07-09 09:20 ? - 106 2018-07-09 09:30 28 ********* 107 2018-07-09 09:40 29 ********** 108 2018-07-09 09:50 30 *********** 109 2018-07-09 10:00 30 *********** 110 2018-07-09 10:10 31 ************ 111 2018-07-09 10:20 31 ************ 112 2018-07-09 10:30 32 ************* ... ..( 11 skipped). .. ************* 124 2018-07-09 12:30 32 ************* 125 2018-07-09 12:40 ? - 126 2018-07-09 12:50 ? - 127 2018-07-09 13:00 ? - 0 2018-07-09 13:10 28 ********* 1 2018-07-09 13:20 28 ********* 2 2018-07-09 13:30 29 ********** ... ..( 8 skipped). .. ********** 11 2018-07-09 15:00 29 ********** 12 2018-07-09 15:10 ? - 13 2018-07-09 15:20 ? - 14 2018-07-09 15:30 ? - 15 2018-07-09 15:40 29 ********** 16 2018-07-09 15:50 ? - 17 2018-07-09 16:00 ? - 18 2018-07-09 16:10 29 ********** ... ..( 3 skipped). .. ********** 22 2018-07-09 16:50 29 ********** 23 2018-07-09 17:00 ? - ... ..( 10 skipped). .. - 34 2018-07-09 18:50 ? - 35 2018-07-09 19:00 30 *********** ... ..( 8 skipped). .. *********** 44 2018-07-09 20:30 30 *********** 45 2018-07-09 20:40 31 ************ 46 2018-07-09 20:50 31 ************ 47 2018-07-09 21:00 30 *********** ... ..( 2 skipped). .. *********** 50 2018-07-09 21:30 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 50 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 50 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc === START OF INFORMATION SECTION === Model Family: Indilinx Barefoot 3 based SSDs Device Model: OCZ-VECTOR150 Serial Number: -- LU WWN Device Id: 5 e83a97 ... Firmware Version: 1.2 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jul 9 21:38:25 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x1d) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x00) Error logging NOT supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 0) minutes. Extended self-test routine recommended polling time: ( 0) minutes. SMART Attributes Data Structure revision number: 18 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Runtime_Bad_Block ------ 000 000 000 - 0 9 Power_On_Hours ------ 100 100 000 - 3674 12 Power_Cycle_Count ------ 100 100 000 - 4931 171 Avail_OP_Block_Count ------ 080 080 000 - 39924816 174 Pwr_Cycle_Ct_Unplanned ------ 100 100 000 - 659 195 Total_Prog_Failures ------ 100 100 000 - 0 196 Total_Erase_Failures ------ 100 100 000 - 0 197 Total_Unc_Read_Failures ------ 100 100 000 - 0 208 Average_Erase_Count ------ 100 100 000 - 446 210 SATA_CRC_Error_Count ------ 100 100 000 - 1 224 In_Warranty ------ 100 100 000 - 1 233 Remaining_Lifetime_Perc ------ 086 086 000 - 86 241 Host_Writes_GiB ------ 100 100 000 - 18740 242 Host_Reads_GiB ------ 100 100 000 - 4195 249 Total_NAND_Prog_Ct_GiB ------ 100 100 000 - 846514097 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 51 Comprehensive SMART error log 0x03 GPL,SL R/O 77 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log Version: 18 (77 sectors) No Errors Logged Warning! SMART Extended Self-test Log Structure error: invalid SMART checksum. SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported ATA_READ_LOG_EXT (addr=0x11:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read SATA Phy Event Counters failed