/dev/nvme0n1 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.13.7-arch1-1] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: Samsung SSD 970 EVO 500GB Serial Number: -- Firmware Version: 2B2QEXE7 PCI Vendor/Subsystem ID: 0x144d IEEE OUI Identifier: 0x002538 Total NVM Capacity: 500,107,862,016 [500 GB] Unallocated NVM Capacity: 0 Controller ID: 4 NVMe Version: 1.3 Number of Namespaces: 1 Namespace 1 Size/Capacity: 500,107,862,016 [500 GB] Namespace 1 Utilization: 196,420,251,648 [196 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 002538 ... Local Time is: Sun Jun 15 07:16:01 2025 EDT Firmware Updates (0x16): 3 Slots, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x005f): Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp Log Page Attributes (0x03): S/H_per_NS Cmd_Eff_Lg Maximum Data Transfer Size: 512 Pages Warning Comp. Temp. Threshold: 85 Celsius Critical Comp. Temp. Threshold: 85 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 6.20W - - 0 0 0 0 0 0 1 + 4.30W - - 1 1 1 1 0 0 2 + 2.10W - - 2 2 2 2 0 0 3 - 0.0400W - - 3 3 3 3 210 1200 4 - 0.0050W - - 4 4 4 4 2000 8000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 31 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 0% Data Units Read: 12,347,890 [6.32 TB] Data Units Written: 14,113,665 [7.22 TB] Host Read Commands: 203,479,980 Host Write Commands: 223,093,255 Controller Busy Time: 683 Power Cycles: 1,081 Power On Hours: 1,066 Unsafe Shutdowns: 42 Media and Data Integrity Errors: 0 Error Information Log Entries: 1,064 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 31 Celsius Temperature Sensor 2: 42 Celsius Error Information (NVMe Log 0x01, 16 of 64 entries) No Errors Logged Self-test Log (NVMe Log 0x06) Self-test status: No self-test in progress No Self-tests Logged /dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.13.7-arch1-1] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Marvell based SanDisk SSDs Device Model: SanDisk SSD PLUS 1000GB Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: UH4400RL User Capacity: 1,000,207,286,272 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5528 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 15 07:16:01 2025 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x15) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 5094 12 Power_Cycle_Count -O--CK 100 100 000 - 1077 165 Total_Write/Erase_Count -O--CK 100 100 000 - 203 166 Min_W/E_Cycle -O--CK 100 100 --- - 1 167 Min_Bad_Block/Die -O--CK 100 100 --- - 0 168 Maximum_Erase_Cycle -O--CK 100 100 --- - 3 169 Total_Bad_Block -O--CK 100 100 --- - 808 170 Unknown_Marvell_Attr -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Avg_Write/Erase_Count -O--CK 100 100 000 - 1 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 34 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 3173 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 091 068 000 - 9 (Min/Max 2/68) 199 SATA_CRC_Error -O--CK 100 100 --- - 0 230 Perc_Write/Erase_Count -O--CK 100 100 000 - 58 20 58 232 Perc_Avail_Resrvd_Space PO--CK 100 100 005 - 100 233 Total_NAND_Writes_GiB -O--CK 100 100 --- - 1012 234 Perc_Write/Erase_Ct_BC -O--CK 100 100 000 - 3189 241 Total_Writes_GiB ----CK 100 100 000 - 1334 242 Total_Reads_GiB ----CK 100 100 000 - 1038 244 Thermal_Throttle -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3-0xa4 GPL,SL VS 1 Device vendor specific log 0xa7 GPL,SL VS 1 Device vendor specific log 0xa9 GPL,SL VS 3 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (16 sectors) Device Error Count: 3173 (device log contains only the most recent 64 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3173 [2] occurred at disk power-on lifetime: 5096 hours (212 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 00 00 00 04 a0 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:00:15.323 SET FEATURES [Enable SATA feature] ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:15.206 FLUSH CACHE EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:05:12.214 FLUSH CACHE EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:05:33.792 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:05:33.742 READ LOG EXT Error 3172 [1] occurred at disk power-on lifetime: 5096 hours (212 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 4c 00 00 00 00 00 4c a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:15.206 FLUSH CACHE EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:05:12.214 FLUSH CACHE EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:05:33.792 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:05:33.742 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:05:33.691 READ LOG EXT Error 3171 [0] occurred at disk power-on lifetime: 5096 hours (212 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 70 00 00 00 00 08 70 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:08.576 FLUSH CACHE EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:05:33.792 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:05:33.742 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:05:33.691 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:05:33.607 READ LOG EXT Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. Error 3170 [63] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 45 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 44 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 43 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 42 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 41 3d+07:32:11.153 NOP [Abort queued commands] Error 3169 [62] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 35 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 34 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 33 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 32 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 31 3d+07:32:11.153 NOP [Abort queued commands] Error 3168 [61] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 25 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 24 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 23 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 22 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 21 3d+07:32:11.153 NOP [Abort queued commands] Error 3167 [60] occurred at disk power-on lifetime: 43981 hours (1832 days + 13 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 15 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 14 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 13 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 12 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 11 3d+07:32:11.153 NOP [Abort queued commands] Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. Error 3166 [59] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 45 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 44 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 43 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 42 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 41 3d+07:32:11.153 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1077 --- Lifetime Power-On Resets 0x01 0x010 4 5094 --- Power-on Hours 0x01 0x018 6 2799659618 --- Logical Sectors Written 0x01 0x028 6 2178171150 --- Logical Sectors Read 0x01 0x038 6 5096 --- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 9 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 76 --- Highest Temperature 0x05 0x028 1 10 --- Lowest Temperature 0x05 0x030 1 27 --- Highest Average Short Term Temperature 0x05 0x038 1 27 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 41 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error /dev/sdb smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.13.7-arch1-1] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 860 EVO 1TB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: RVT04B6Q User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 15 07:16:01 2025 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 099 099 000 - 2725 12 Power_Cycle_Count -O--CK 099 099 000 - 464 177 Wear_Leveling_Count PO--C- 100 100 000 - 0 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 078 059 000 - 22 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 29 241 Total_LBAs_Written -O--CK 099 099 000 - 532423156 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 40/40 Celsius Lifetime Min/Max Temperature: 20/40 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (55) Index Estimated Time Temperature Celsius 56 2025-06-14 10:00 21 ** 57 2025-06-14 10:10 22 *** 58 2025-06-14 10:20 23 **** 59 2025-06-14 10:30 24 ***** 60 2025-06-14 10:40 24 ***** 61 2025-06-14 10:50 ? - 62 2025-06-14 11:00 24 ***** 63 2025-06-14 11:10 ? - 64 2025-06-14 11:20 21 ** 65 2025-06-14 11:30 ? - 66 2025-06-14 11:40 22 *** 67 2025-06-14 11:50 22 *** 68 2025-06-14 12:00 ? - 69 2025-06-14 12:10 ? - 70 2025-06-14 12:20 21 ** 71 2025-06-14 12:30 22 *** 72 2025-06-14 12:40 23 **** 73 2025-06-14 12:50 24 ***** 74 2025-06-14 13:00 24 ***** 75 2025-06-14 13:10 25 ****** 76 2025-06-14 13:20 25 ****** 77 2025-06-14 13:30 24 ***** 78 2025-06-14 13:40 24 ***** 79 2025-06-14 13:50 ? - 80 2025-06-14 14:00 24 ***** 81 2025-06-14 14:10 24 ***** 82 2025-06-14 14:20 24 ***** 83 2025-06-14 14:30 ? - 84 2025-06-14 14:40 20 * 85 2025-06-14 14:50 21 ** 86 2025-06-14 15:00 ? - 87 2025-06-14 15:10 21 ** 88 2025-06-14 15:20 22 *** 89 2025-06-14 15:30 22 *** 90 2025-06-14 15:40 23 **** ... ..( 4 skipped). .. **** 95 2025-06-14 16:30 23 **** 96 2025-06-14 16:40 24 ***** ... ..( 24 skipped). .. ***** 121 2025-06-14 20:50 24 ***** 122 2025-06-14 21:00 ? - 123 2025-06-14 21:10 21 ** 124 2025-06-14 21:20 22 *** 125 2025-06-14 21:30 23 **** 126 2025-06-14 21:40 ? - 127 2025-06-14 21:50 22 *** 0 2025-06-14 22:00 ? - 1 2025-06-14 22:10 20 * 2 2025-06-14 22:20 21 ** 3 2025-06-14 22:30 22 *** 4 2025-06-14 22:40 ? - 5 2025-06-14 22:50 22 *** 6 2025-06-14 23:00 ? - 7 2025-06-14 23:10 22 *** 8 2025-06-14 23:20 23 **** 9 2025-06-14 23:30 ? - 10 2025-06-14 23:40 21 ** 11 2025-06-14 23:50 22 *** 12 2025-06-15 00:00 ? - 13 2025-06-15 00:10 ? - 14 2025-06-15 00:20 23 **** 15 2025-06-15 00:30 25 ****** 16 2025-06-15 00:40 25 ****** 17 2025-06-15 00:50 ? - 18 2025-06-15 01:00 23 **** 19 2025-06-15 01:10 22 *** 20 2025-06-15 01:20 ? - 21 2025-06-15 01:30 22 *** 22 2025-06-15 01:40 23 **** 23 2025-06-15 01:50 23 **** 24 2025-06-15 02:00 24 ***** 25 2025-06-15 02:10 24 ***** 26 2025-06-15 02:20 25 ****** 27 2025-06-15 02:30 24 ***** 28 2025-06-15 02:40 24 ***** 29 2025-06-15 02:50 ? - 30 2025-06-15 03:00 22 *** 31 2025-06-15 03:10 23 **** 32 2025-06-15 03:20 23 **** 33 2025-06-15 03:30 ? - 34 2025-06-15 03:40 24 ***** 35 2025-06-15 03:50 24 ***** 36 2025-06-15 04:00 ? - 37 2025-06-15 04:10 21 ** 38 2025-06-15 04:20 ? - 39 2025-06-15 04:30 ? - 40 2025-06-15 04:40 24 ***** 41 2025-06-15 04:50 24 ***** 42 2025-06-15 05:00 25 ****** 43 2025-06-15 05:10 26 ******* 44 2025-06-15 05:20 ? - 45 2025-06-15 05:30 24 ***** 46 2025-06-15 05:40 25 ****** 47 2025-06-15 05:50 ? - 48 2025-06-15 06:00 24 ***** 49 2025-06-15 06:10 25 ****** 50 2025-06-15 06:20 25 ****** 51 2025-06-15 06:30 26 ******* 52 2025-06-15 06:40 ? - 53 2025-06-15 06:50 26 ******* 54 2025-06-15 07:00 26 ******* 55 2025-06-15 07:10 ? - SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 464 --- Lifetime Power-On Resets 0x01 0x010 4 2725 --- Power-on Hours 0x01 0x018 6 532423156 --- Logical Sectors Written 0x01 0x020 6 2317655 --- Number of Write Commands 0x01 0x028 6 518245450 --- Logical Sectors Read 0x01 0x030 6 2532935 --- Number of Read Commands 0x01 0x038 6 2784000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 261 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 22 --- Current Temperature 0x05 0x020 1 40 --- Highest Temperature 0x05 0x028 1 20 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 2603 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.13.7-arch1-1] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device Model: ST31500341AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC1H User Capacity: 1,500,301,910,016 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jun 15 07:16:01 2025 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 0 (vendor specific), recommended: 254 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 617) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 294) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 111 099 006 - 36682765 3 Spin_Up_Time PO---- 100 092 000 - 0 4 Start_Stop_Count -O--CK 089 089 020 - 12199 5 Reallocated_Sector_Ct PO--CK 076 076 036 - 1021 7 Seek_Error_Rate POSR-- 083 060 030 - 218978479 9 Power_On_Hours -O--CK 068 068 000 - 28438 10 Spin_Retry_Count PO--C- 100 100 097 - 10 12 Power_Cycle_Count -O--CK 096 096 020 - 5023 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 097 000 - 17180328628 189 High_Fly_Writes -O-RCK 001 001 000 - 167 190 Airflow_Temperature_Cel -O---K 074 052 045 - 26 (Min/Max 21/26) 194 Temperature_Celsius -O---K 026 048 000 - 26 (0 16 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 021 016 000 - 36682765 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 25089 (104 187 0) 241 Total_LBAs_Written ------ 100 253 000 - 3602878936 242 Total_LBAs_Read ------ 100 253 000 - 476647745 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 21/25 Celsius Lifetime Min/Max Temperature: 16/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (75) Index Estimated Time Temperature Celsius 76 2025-06-15 05:09 34 *************** 77 2025-06-15 05:10 34 *************** 78 2025-06-15 05:11 34 *************** 79 2025-06-15 05:12 35 **************** ... ..( 2 skipped). .. **************** 82 2025-06-15 05:15 35 **************** 83 2025-06-15 05:16 36 ***************** ... ..( 3 skipped). .. ***************** 87 2025-06-15 05:20 36 ***************** 88 2025-06-15 05:21 37 ****************** ... ..( 3 skipped). .. ****************** 92 2025-06-15 05:25 37 ****************** 93 2025-06-15 05:26 38 ******************* 94 2025-06-15 05:27 ? - 95 2025-06-15 05:28 24 ***** 96 2025-06-15 05:29 25 ****** 97 2025-06-15 05:30 25 ****** 98 2025-06-15 05:31 26 ******* 99 2025-06-15 05:32 27 ******** 100 2025-06-15 05:33 27 ******** 101 2025-06-15 05:34 28 ********* 102 2025-06-15 05:35 28 ********* 103 2025-06-15 05:36 29 ********** 104 2025-06-15 05:37 30 *********** 105 2025-06-15 05:38 30 *********** 106 2025-06-15 05:39 30 *********** 107 2025-06-15 05:40 31 ************ 108 2025-06-15 05:41 31 ************ 109 2025-06-15 05:42 32 ************* 110 2025-06-15 05:43 32 ************* 111 2025-06-15 05:44 32 ************* 112 2025-06-15 05:45 33 ************** 113 2025-06-15 05:46 33 ************** 114 2025-06-15 05:47 33 ************** 115 2025-06-15 05:48 34 *************** ... ..( 2 skipped). .. *************** 118 2025-06-15 05:51 34 *************** 119 2025-06-15 05:52 35 **************** ... ..( 2 skipped). .. **************** 122 2025-06-15 05:55 35 **************** 123 2025-06-15 05:56 ? - 124 2025-06-15 05:57 25 ****** 125 2025-06-15 05:58 26 ******* 126 2025-06-15 05:59 27 ******** 127 2025-06-15 06:00 27 ******** 0 2025-06-15 06:01 28 ********* 1 2025-06-15 06:02 28 ********* 2 2025-06-15 06:03 29 ********** 3 2025-06-15 06:04 29 ********** 4 2025-06-15 06:05 30 *********** 5 2025-06-15 06:06 30 *********** 6 2025-06-15 06:07 31 ************ 7 2025-06-15 06:08 31 ************ 8 2025-06-15 06:09 32 ************* 9 2025-06-15 06:10 32 ************* 10 2025-06-15 06:11 32 ************* 11 2025-06-15 06:12 33 ************** 12 2025-06-15 06:13 33 ************** 13 2025-06-15 06:14 33 ************** 14 2025-06-15 06:15 34 *************** ... ..( 2 skipped). .. *************** 17 2025-06-15 06:18 34 *************** 18 2025-06-15 06:19 35 **************** ... ..( 4 skipped). .. **************** 23 2025-06-15 06:24 35 **************** 24 2025-06-15 06:25 36 ***************** ... ..( 4 skipped). .. ***************** 29 2025-06-15 06:30 36 ***************** 30 2025-06-15 06:31 37 ****************** ... ..( 3 skipped). .. ****************** 34 2025-06-15 06:35 37 ****************** 35 2025-06-15 06:36 38 ******************* ... ..( 5 skipped). .. ******************* 41 2025-06-15 06:42 38 ******************* 42 2025-06-15 06:43 ? - 43 2025-06-15 06:44 35 **************** 44 2025-06-15 06:45 35 **************** 45 2025-06-15 06:46 36 ***************** ... ..( 3 skipped). .. ***************** 49 2025-06-15 06:50 36 ***************** 50 2025-06-15 06:51 37 ****************** ... ..( 3 skipped). .. ****************** 54 2025-06-15 06:55 37 ****************** 55 2025-06-15 06:56 38 ******************* ... ..( 11 skipped). .. ******************* 67 2025-06-15 07:08 38 ******************* 68 2025-06-15 07:09 ? - 69 2025-06-15 07:10 21 ** 70 2025-06-15 07:11 22 *** 71 2025-06-15 07:12 22 *** 72 2025-06-15 07:13 23 **** 73 2025-06-15 07:14 24 ***** 74 2025-06-15 07:15 25 ****** 75 2025-06-15 07:16 25 ****** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS