/dev/sda === START OF INFORMATION SECTION === Device Model: Hitachi HCT721016SLA380 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: ST1OA31E User Capacity: 160 041 885 696 bytes [160 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Jun 13 00:45:47 2016 SAMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2371) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 40) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 130 130 054 - 121 3 Spin_Up_Time POS--- 115 115 024 - 210 (Average 222) 4 Start_Stop_Count -O--C- 099 099 000 - 4337 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 125 125 020 - 33 9 Power_On_Hours -O--C- 099 099 000 - 10671 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 4105 192 Power-Off_Retract_Count -O--CK 097 097 000 - 4382 193 Load_Cycle_Count -O--C- 097 097 000 - 4382 194 Temperature_Celsius -O---- 142 142 000 - 42 (Min/Max 22/52) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 3 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 9746 hours (406 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 a0 00 00 09 77 3a 18 e9 00 Error: ICRC, ABRT 160 sectors at LBA = 0x09773a18 = 158808600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 01 00 00 00 09 77 39 b8 e0 00 00:51:11.100 WRITE DMA EXT 35 00 00 01 00 00 00 09 77 38 b8 e0 00 00:51:11.100 WRITE DMA EXT 35 00 00 01 00 00 00 09 77 37 b8 e0 00 00:51:11.100 WRITE DMA EXT 35 00 00 01 00 00 00 09 77 36 b8 e0 00 00:51:11.100 WRITE DMA EXT 35 00 00 01 00 00 00 09 77 35 b8 e0 00 00:51:11.100 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 9260 - # 2 Extended offline Completed without error 00% 8731 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: 29/43 Celsius Lifetime Min/Max Temperature: 22/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (50) Index Estimated Time Temperature Celsius 51 2016-06-12 22:38 37 ****************** 52 2016-06-12 22:39 37 ****************** 53 2016-06-12 22:40 37 ****************** 54 2016-06-12 22:41 38 ******************* ... ..( 2 skipped). .. ******************* 57 2016-06-12 22:44 38 ******************* 58 2016-06-12 22:45 39 ******************** ... ..( 5 skipped). .. ******************** 64 2016-06-12 22:51 39 ******************** 65 2016-06-12 22:52 40 ********************* ... ..( 5 skipped). .. ********************* 71 2016-06-12 22:58 40 ********************* 72 2016-06-12 22:59 41 ********************** ... ..( 11 skipped). .. ********************** 84 2016-06-12 23:11 41 ********************** 85 2016-06-12 23:12 42 *********************** ... ..( 12 skipped). .. *********************** 98 2016-06-12 23:25 42 *********************** 99 2016-06-12 23:26 ? - 100 2016-06-12 23:27 30 *********** 101 2016-06-12 23:28 31 ************ 102 2016-06-12 23:29 31 ************ 103 2016-06-12 23:30 32 ************* 104 2016-06-12 23:31 32 ************* 105 2016-06-12 23:32 33 ************** 106 2016-06-12 23:33 33 ************** 107 2016-06-12 23:34 34 *************** 108 2016-06-12 23:35 34 *************** 109 2016-06-12 23:36 34 *************** 110 2016-06-12 23:37 35 **************** 111 2016-06-12 23:38 35 **************** 112 2016-06-12 23:39 35 **************** 113 2016-06-12 23:40 36 ***************** 114 2016-06-12 23:41 36 ***************** 115 2016-06-12 23:42 36 ***************** 116 2016-06-12 23:43 37 ****************** 117 2016-06-12 23:44 37 ****************** 118 2016-06-12 23:45 37 ****************** 119 2016-06-12 23:46 38 ******************* ... ..( 2 skipped). .. ******************* 122 2016-06-12 23:49 38 ******************* 123 2016-06-12 23:50 39 ******************** ... ..( 2 skipped). .. ******************** 126 2016-06-12 23:53 39 ******************** 127 2016-06-12 23:54 40 ********************* ... ..( 4 skipped). .. ********************* 4 2016-06-12 23:59 40 ********************* 5 2016-06-13 00:00 41 ********************** ... ..( 8 skipped). .. ********************** 14 2016-06-13 00:09 41 ********************** 15 2016-06-13 00:10 42 *********************** 16 2016-06-13 00:11 42 *********************** 17 2016-06-13 00:12 41 ********************** 18 2016-06-13 00:13 42 *********************** ... ..( 24 skipped). .. *********************** 43 2016-06-13 00:38 42 *********************** 44 2016-06-13 00:39 43 ************************ 45 2016-06-13 00:40 42 *********************** 46 2016-06-13 00:41 43 ************************ 47 2016-06-13 00:42 42 *********************** ... ..( 2 skipped). .. *********************** 50 2016-06-13 00:45 42 *********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.9 Device Model: ST3160212ACE Serial Number: -- Firmware Version: 3.ACB User Capacity: 160 041 885 696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Mon Jun 13 00:45:48 2016 SAMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (15556) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 54) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 095 071 006 - 118580359 3 Spin_Up_Time PO---- 095 092 000 - 0 4 Start_Stop_Count -O--CK 094 094 020 - 6208 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 049 047 030 - 3590663721938 9 Power_On_Hours -O--CK 089 089 000 - 10228 10 Spin_Retry_Count PO--C- 100 099 097 - 0 12 Power_Cycle_Count -O--CK 095 095 020 - 5513 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 094 094 000 - 6 190 Airflow_Temperature_Cel -O---K 059 050 045 - 41 (Min/Max 28/41) 194 Temperature_Celsius -O---K 041 050 000 - 41 (0 19 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 069 050 000 - 118580359 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 095 000 - 285 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23552 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 337 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 337 [16] occurred at disk power-on lifetime: 6787 hours (282 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 08 00 00 03 e0 00 02:34:39.854 READ DMA EXT 25 00 00 00 01 00 00 08 00 00 02 e0 00 02:34:39.462 READ DMA EXT 25 00 00 00 01 00 00 08 00 00 01 e0 00 02:34:38.839 READ DMA EXT 25 00 00 00 01 00 00 08 00 00 00 e0 00 02:34:38.196 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 02:34:38.138 READ DMA EXT Error 336 [15] occurred at disk power-on lifetime: 6787 hours (282 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 08 00 00 00 e0 00 02:34:11.849 READ DMA EXT 35 00 00 01 00 00 00 ad 00 03 98 e0 00 02:34:11.892 WRITE DMA EXT ea 00 00 00 00 00 00 75 00 03 38 a0 00 02:34:11.890 FLUSH CACHE EXT 35 00 00 00 08 00 00 75 00 03 38 e0 00 02:34:11.854 WRITE DMA EXT 35 00 00 00 18 00 00 7a 00 03 20 e0 00 02:34:11.853 WRITE DMA EXT Error 335 [14] occurred at disk power-on lifetime: 6787 hours (282 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 a3 00 03 38 e0 00 02:34:10.071 READ DMA EXT 35 00 00 00 08 00 00 09 00 00 28 e0 00 02:34:09.520 WRITE DMA EXT 35 00 00 00 08 00 00 ac 00 03 f8 e0 00 02:34:09.340 WRITE DMA EXT 35 00 00 00 08 00 00 09 00 00 20 e0 00 02:34:09.320 WRITE DMA EXT 35 00 00 00 08 00 00 09 00 00 18 e0 00 02:27:28.751 WRITE DMA EXT Error 334 [13] occurred at disk power-on lifetime: 6787 hours (282 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 08 00 00 00 e0 00 02:27:22.629 READ DMA EXT 35 00 00 00 e0 00 00 ae 00 03 70 e0 00 02:27:22.628 WRITE DMA EXT 35 00 00 01 00 00 00 ad 00 03 70 e0 00 02:27:22.628 WRITE DMA EXT 35 00 00 00 18 00 00 ad 00 03 50 e0 00 02:27:22.628 WRITE DMA EXT 35 00 00 00 08 00 00 08 00 00 10 e0 00 02:27:22.627 WRITE DMA EXT Error 333 [12] occurred at disk power-on lifetime: 6787 hours (282 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 0f 00 00 08 00 00 01 e0 00 02:27:15.833 READ DMA EXT 35 00 00 00 0f 00 00 08 00 00 01 e0 00 02:27:15.794 WRITE DMA EXT 25 00 00 00 01 00 00 f7 00 0a ff e0 00 02:27:15.421 READ DMA EXT 35 00 00 00 01 00 00 f7 00 0a ff e0 00 02:27:15.420 WRITE DMA EXT 25 00 00 00 01 00 00 08 00 00 00 e0 00 02:27:15.420 READ DMA EXT Error 332 [11] occurred at disk power-on lifetime: 6787 hours (282 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 16 00 00 ad 00 03 28 e0 00 02:27:15.411 READ DMA EXT 25 00 00 00 02 00 00 ad 00 03 5a e0 00 02:27:15.411 READ DMA EXT 35 00 00 00 02 00 00 ad 00 03 5a e0 00 02:27:15.421 WRITE DMA EXT 25 00 00 00 01 00 00 ad 00 03 48 e0 00 02:27:15.420 READ DMA EXT 35 00 00 00 01 00 00 ad 00 03 48 e0 00 02:27:15.420 WRITE DMA EXT Error 331 [10] occurred at disk power-on lifetime: 6787 hours (282 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 80 00 05 00 e0 00 02:27:12.048 READ DMA EXT 29 00 00 00 01 00 00 f7 00 0a ff e0 00 02:27:11.948 READ MULTIPLE EXT 25 00 00 00 01 00 00 f7 00 0a ff e0 00 02:27:11.915 READ DMA EXT 25 00 00 00 0d 00 00 08 00 00 00 e0 00 02:27:11.553 READ DMA EXT 25 00 00 00 04 00 00 08 00 00 40 e0 00 02:27:11.523 READ DMA EXT Error 330 [9] occurred at disk power-on lifetime: 6787 hours (282 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 f7 00 0a ff e0 00 02:27:12.048 READ DMA EXT 25 00 00 00 0d 00 00 08 00 00 00 e0 00 02:27:11.948 READ DMA EXT 25 00 00 00 04 00 00 08 00 00 40 e0 00 02:27:11.915 READ DMA EXT 25 00 00 00 01 00 00 08 00 00 00 e0 00 02:27:11.553 READ DMA EXT ec 00 00 01 00 00 ff ff 00 ff ff a0 00 02:27:11.523 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 8677 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported