/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST750LM022 HN-M750MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2AR10002 User Capacity: 750,156,374,016 bytes [750 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat May 4 18:38:46 2019 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9540) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 159) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 18 2 Throughput_Performance POS--K 055 050 000 - 8782 3 Spin_Up_Time PO---K 089 089 025 - 3464 4 Start_Stop_Count -O--CK 097 097 000 - 3951 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate POSR-K 252 252 051 - 0 8 Seek_Time_Performance P-S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 7551 10 Spin_Retry_Count PO--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 259 12 Power_Cycle_Count -O--CK 097 097 000 - 3823 181 Program_Fail_Cnt_Total -O---K 100 100 000 - 6516534 183 Runtime_Bad_Block -O--CK 252 252 010 - 0 184 End-to-End_Error PO--CK 252 252 048 - 0 186 Unknown_Attribute -O--CK 252 252 000 - 0 187 Reported_Uncorrect -O--CK 252 252 000 - 0 188 Command_Timeout -O--CK 252 252 000 - 0 190 Airflow_Temperature_Cel -O---- 069 052 040 - 31 (Min/Max 17/49) 191 G-Sense_Error_Rate -O---K 100 100 000 - 189 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 193 Load_Cycle_Count -O--CK 097 097 000 - 36814 194 Temperature_Celsius -O---- 064 052 000 - 31 (Min/Max 17/49) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 23795 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 7508 - # 2 Extended offline Aborted by host 70% 7483 - # 3 Extended offline Aborted by host 70% 7459 - # 4 Extended offline Aborted by host 60% 7434 - # 5 Extended offline Aborted by host 60% 7416 - # 6 Extended offline Aborted by host 20% 7392 - # 7 Extended offline Aborted by host 20% 7354 - # 8 Extended offline Aborted by host 90% 7302 - # 9 Extended offline Aborted by host 60% 7293 - #10 Extended offline Completed without error 00% 7269 - #11 Extended offline Aborted by host 20% 7234 - #12 Extended offline Completed without error 00% 7225 - #13 Extended offline Aborted by host 70% 7217 - #14 Extended offline Completed without error 00% 7187 - #15 Extended offline Aborted by host 40% 7171 - #16 Extended offline Completed without error 00% 7146 - #17 Extended offline Aborted by host 90% 7090 - #18 Extended offline Aborted by host 80% 7074 - #19 Extended offline Interrupted (host reset) 90% 7059 - #20 Extended offline Interrupted (host reset) 60% 7025 - #21 Extended offline Aborted by host 80% 6982 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 25/31 Celsius Lifetime Min/Max Temperature: 17/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (111) Index Estimated Time Temperature Celsius 112 2019-05-04 08:00 31 ************ 113 2019-05-04 08:05 37 ****************** ... ..( 4 skipped). .. ****************** 118 2019-05-04 08:30 37 ****************** 119 2019-05-04 08:35 36 ***************** ... ..( 10 skipped). .. ***************** 2 2019-05-04 09:30 36 ***************** 3 2019-05-04 09:35 35 **************** ... ..( 2 skipped). .. **************** 6 2019-05-04 09:50 35 **************** 7 2019-05-04 09:55 28 ********* 8 2019-05-04 10:00 29 ********** 9 2019-05-04 10:05 31 ************ 10 2019-05-04 10:10 32 ************* 11 2019-05-04 10:15 33 ************** 12 2019-05-04 10:20 33 ************** 13 2019-05-04 10:25 34 *************** 14 2019-05-04 10:30 34 *************** 15 2019-05-04 10:35 35 **************** 16 2019-05-04 10:40 35 **************** 17 2019-05-04 10:45 35 **************** 18 2019-05-04 10:50 28 ********* 19 2019-05-04 10:55 29 ********** 20 2019-05-04 11:00 31 ************ 21 2019-05-04 11:05 32 ************* 22 2019-05-04 11:10 33 ************** 23 2019-05-04 11:15 27 ******** 24 2019-05-04 11:20 29 ********** 25 2019-05-04 11:25 30 *********** 26 2019-05-04 11:30 32 ************* 27 2019-05-04 11:35 33 ************** 28 2019-05-04 11:40 33 ************** 29 2019-05-04 11:45 33 ************** 30 2019-05-04 11:50 34 *************** 31 2019-05-04 11:55 34 *************** 32 2019-05-04 12:00 34 *************** 33 2019-05-04 12:05 35 **************** 34 2019-05-04 12:10 36 ***************** ... ..( 16 skipped). .. ***************** 51 2019-05-04 13:35 36 ***************** 52 2019-05-04 13:40 28 ********* 53 2019-05-04 13:45 29 ********** 54 2019-05-04 13:50 31 ************ 55 2019-05-04 13:55 32 ************* 56 2019-05-04 14:00 33 ************** 57 2019-05-04 14:05 34 *************** 58 2019-05-04 14:10 34 *************** 59 2019-05-04 14:15 35 **************** 60 2019-05-04 14:20 35 **************** 61 2019-05-04 14:25 36 ***************** ... ..( 16 skipped). .. ***************** 78 2019-05-04 15:50 36 ***************** 79 2019-05-04 15:55 35 **************** 80 2019-05-04 16:00 35 **************** 81 2019-05-04 16:05 25 ****** 82 2019-05-04 16:10 28 ********* 83 2019-05-04 16:15 29 ********** 84 2019-05-04 16:20 30 *********** 85 2019-05-04 16:25 31 ************ 86 2019-05-04 16:30 31 ************ 87 2019-05-04 16:35 32 ************* 88 2019-05-04 16:40 32 ************* 89 2019-05-04 16:45 33 ************** 90 2019-05-04 16:50 33 ************** 91 2019-05-04 16:55 33 ************** 92 2019-05-04 17:00 34 *************** ... ..( 2 skipped). .. *************** 95 2019-05-04 17:15 34 *************** 96 2019-05-04 17:20 35 **************** 97 2019-05-04 17:25 36 ***************** 98 2019-05-04 17:30 37 ****************** ... ..( 5 skipped). .. ****************** 104 2019-05-04 18:00 37 ****************** 105 2019-05-04 18:05 36 ***************** 106 2019-05-04 18:10 36 ***************** 107 2019-05-04 18:15 35 **************** 108 2019-05-04 18:20 35 **************** 109 2019-05-04 18:25 35 **************** 110 2019-05-04 18:30 28 ********* 111 2019-05-04 18:35 30 *********** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific