/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.5-200.fc36.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-22MFCA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Nov 8 15:17:25 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11040) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 114) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 176 051 - 0 3 Spin_Up_Time POS--K 170 163 021 - 2475 4 Start_Stop_Count -O--CK 092 092 000 - 8024 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 072 072 000 - 20816 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 093 093 000 - 7132 192 Power-Off_Retract_Count -O--CK 200 200 000 - 312 193 Load_Cycle_Count -O--CK 197 197 000 - 9561 194 Temperature_Celsius -O---K 112 101 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 48 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1104 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1104 [23] occurred at disk power-on lifetime: 5163 hours (215 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 d8 1f 18 40 00 Error: UNC at LBA = 0x00d81f18 = 14163736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 24 00 38 00 00 00 d8 1f 82 40 00 00:07:32.323 READ FPDMA QUEUED 60 01 00 00 30 00 00 00 d8 1e 82 40 00 00:07:32.323 READ FPDMA QUEUED 60 00 08 00 28 00 00 02 99 bf b0 40 00 00:07:32.320 READ FPDMA QUEUED 60 00 08 00 20 00 00 02 99 bb 90 40 00 00:07:32.319 READ FPDMA QUEUED 60 00 08 00 18 00 00 02 99 b9 90 40 00 00:07:32.310 READ FPDMA QUEUED Error 1103 [22] occurred at disk power-on lifetime: 5160 hours (215 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 d8 1f 18 40 00 Error: UNC at LBA = 0x00d81f18 = 14163736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 24 00 90 00 00 00 d8 1f 82 40 00 01:51:52.964 READ FPDMA QUEUED 60 01 00 00 88 00 00 00 d8 1e 82 40 00 01:51:52.964 READ FPDMA QUEUED 60 00 31 00 80 00 00 00 32 39 a8 40 00 01:51:52.963 READ FPDMA QUEUED 60 00 78 00 78 00 00 00 32 39 30 40 00 01:51:52.963 READ FPDMA QUEUED 60 00 08 00 70 00 00 00 32 37 d0 40 00 01:51:52.962 READ FPDMA QUEUED Error 1102 [21] occurred at disk power-on lifetime: 5160 hours (215 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 d8 1f 18 40 00 Error: UNC at LBA = 0x00d81f18 = 14163736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 24 00 d8 00 00 00 d8 1f 82 40 00 01:24:57.583 READ FPDMA QUEUED 60 01 00 00 d0 00 00 00 d8 1e 82 40 00 01:24:57.583 READ FPDMA QUEUED 60 00 b0 00 c8 00 00 00 28 f0 61 40 00 01:24:57.580 READ FPDMA QUEUED 60 00 04 00 c0 00 00 00 33 28 17 40 00 01:24:57.580 READ FPDMA QUEUED 60 00 0f 00 b8 00 00 00 33 28 08 40 00 01:24:57.580 READ FPDMA QUEUED Error 1101 [20] occurred at disk power-on lifetime: 5158 hours (214 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 d8 1f 18 40 00 Error: UNC at LBA = 0x00d81f18 = 14163736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 24 00 f8 00 00 00 d8 1f 82 40 00 00:09:27.279 READ FPDMA QUEUED 60 01 00 00 f0 00 00 00 d8 1e 82 40 00 00:09:27.279 READ FPDMA QUEUED 60 00 b0 00 e8 00 00 00 28 f0 61 40 00 00:09:27.275 READ FPDMA QUEUED 60 00 58 00 e0 00 00 00 2b f9 ea 40 00 00:09:27.275 READ FPDMA QUEUED 60 00 50 00 d8 00 00 00 16 05 b2 40 00 00:09:27.270 READ FPDMA QUEUED Error 1100 [19] occurred at disk power-on lifetime: 5148 hours (214 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 d8 1f 18 40 00 Error: UNC at LBA = 0x00d81f18 = 14163736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 24 00 d0 00 00 00 d8 1f 82 40 00 00:19:05.111 READ FPDMA QUEUED 60 01 00 00 c8 00 00 00 d8 1e 82 40 00 00:19:05.111 READ FPDMA QUEUED 60 00 08 00 c0 00 00 00 30 65 e2 40 00 00:19:05.107 READ FPDMA QUEUED 60 00 0f 00 b8 00 00 00 32 39 a9 40 00 00:19:05.106 READ FPDMA QUEUED 60 00 18 00 b0 00 00 00 32 39 4f 40 00 00:19:05.106 READ FPDMA QUEUED Error 1099 [18] occurred at disk power-on lifetime: 5148 hours (214 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 d8 1f 18 40 00 Error: UNC at LBA = 0x00d81f18 = 14163736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 a8 00 00 00 97 26 58 40 00 00:08:15.698 READ FPDMA QUEUED 60 00 24 00 a0 00 00 00 d8 1f 82 40 00 00:08:15.689 READ FPDMA QUEUED 60 01 00 00 98 00 00 00 d8 1e 82 40 00 00:08:15.689 READ FPDMA QUEUED 60 00 26 00 90 00 00 00 45 c9 8b 40 00 00:08:15.687 READ FPDMA QUEUED 60 00 08 00 88 00 00 00 45 c6 db 40 00 00:08:15.684 READ FPDMA QUEUED Error 1098 [17] occurred at disk power-on lifetime: 5148 hours (214 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 d8 1f 18 40 00 Error: UNC at LBA = 0x00d81f18 = 14163736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 24 00 d0 00 00 00 d8 1f 82 40 00 00:07:34.036 READ FPDMA QUEUED 60 01 00 00 c8 00 00 00 d8 1e 82 40 00 00:07:34.036 READ FPDMA QUEUED 60 00 09 00 c0 00 00 00 2b fa 53 40 00 00:07:34.035 READ FPDMA QUEUED 60 00 02 00 b8 00 00 00 2b fa 51 40 00 00:07:34.035 READ FPDMA QUEUED 60 00 67 00 b0 00 00 00 2b f9 ea 40 00 00:07:34.032 READ FPDMA QUEUED Error 1097 [16] occurred at disk power-on lifetime: 5146 hours (214 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 d8 1f 18 40 00 Error: UNC at LBA = 0x00d81f18 = 14163736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 24 00 88 00 00 00 d8 1f 82 40 00 02:33:49.553 READ FPDMA QUEUED 60 01 00 00 80 00 00 00 d8 1e 82 40 00 02:33:49.553 READ FPDMA QUEUED 61 00 08 00 78 00 00 19 11 38 08 40 00 02:33:47.680 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 00 02:33:47.662 FLUSH CACHE EXT 61 00 08 00 68 00 00 19 11 38 10 40 00 02:33:47.662 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 15975 - # 2 Short offline Completed without error 00% 15975 - # 3 Extended offline Completed without error 00% 14604 - # 4 Short offline Completed without error 00% 14601 - # 5 Conveyance offline Completed without error 00% 14601 - # 6 Short offline Completed without error 00% 10951 - # 7 Short offline Completed without error 00% 9248 - # 8 Short offline Completed without error 00% 2713 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 22/32 Celsius Lifetime Min/Max Temperature: 8/42 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (351) Index Estimated Time Temperature Celsius 352 2022-11-08 07:20 32 ************* ... ..( 82 skipped). .. ************* 435 2022-11-08 08:43 32 ************* 436 2022-11-08 08:44 33 ************** ... ..( 6 skipped). .. ************** 443 2022-11-08 08:51 33 ************** 444 2022-11-08 08:52 32 ************* ... ..(145 skipped). .. ************* 112 2022-11-08 11:18 32 ************* 113 2022-11-08 11:19 31 ************ ... ..( 31 skipped). .. ************ 145 2022-11-08 11:51 31 ************ 146 2022-11-08 11:52 ? - 147 2022-11-08 11:53 22 *** 148 2022-11-08 11:54 22 *** 149 2022-11-08 11:55 22 *** 150 2022-11-08 11:56 23 **** 151 2022-11-08 11:57 23 **** 152 2022-11-08 11:58 24 ***** 153 2022-11-08 11:59 25 ****** 154 2022-11-08 12:00 25 ****** 155 2022-11-08 12:01 25 ****** 156 2022-11-08 12:02 26 ******* 157 2022-11-08 12:03 26 ******* 158 2022-11-08 12:04 26 ******* 159 2022-11-08 12:05 27 ******** ... ..( 2 skipped). .. ******** 162 2022-11-08 12:08 27 ******** 163 2022-11-08 12:09 28 ********* ... ..( 4 skipped). .. ********* 168 2022-11-08 12:14 28 ********* 169 2022-11-08 12:15 29 ********** ... ..( 10 skipped). .. ********** 180 2022-11-08 12:26 29 ********** 181 2022-11-08 12:27 30 *********** ... ..( 56 skipped). .. *********** 238 2022-11-08 13:24 30 *********** 239 2022-11-08 13:25 31 ************ ... ..( 15 skipped). .. ************ 255 2022-11-08 13:41 31 ************ 256 2022-11-08 13:42 32 ************* 257 2022-11-08 13:43 31 ************ ... ..( 87 skipped). .. ************ 345 2022-11-08 15:11 31 ************ 346 2022-11-08 15:12 32 ************* ... ..( 4 skipped). .. ************* 351 2022-11-08 15:17 32 ************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 11929 Vendor specific /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.5-200.fc36.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 (CMR) Device Model: ST1000DM010-2EP102 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC43 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Nov 8 15:17:25 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 105) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 067 063 006 - 5536801 3 Spin_Up_Time PO---- 097 096 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3200 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 075 060 045 - 37519127 9 Power_On_Hours -O--CK 095 095 000 - 5058 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1698 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 0 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 070 061 040 - 30 (Min/Max 18/31) 193 Load_Cycle_Count -O--CK 099 099 000 - 3211 194 Temperature_Celsius -O---K 030 009 000 - 30 (0 9 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 002 001 000 - 5536801 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 4332h+17m+08.676s 241 Total_LBAs_Written ------ 100 253 000 - 20805704288 242 Total_LBAs_Read ------ 100 253 000 - 14472480336 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4120 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 4800 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 210 - # 2 Short offline Completed without error 00% 210 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 18/31 Celsius Lifetime Min/Max Temperature: 8/39 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1698 --- Lifetime Power-On Resets 0x01 0x010 4 5058 --- Power-on Hours 0x01 0x018 6 20805704288 --- Logical Sectors Written 0x01 0x020 6 105623909 --- Number of Write Commands 0x01 0x028 6 14472480336 --- Logical Sectors Read 0x01 0x030 6 91362686 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 3370167045 N-- Spindle Motor Power-on Hours 0x03 0x010 4 3370167045 N-- Head Flying Hours 0x03 0x018 4 3211 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 30 --- Current Temperature 0x05 0x010 1 29 --- Average Short Term Temperature 0x05 0x018 1 30 --- Average Long Term Temperature 0x05 0x020 1 39 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 35 --- Highest Average Short Term Temperature 0x05 0x038 1 21 --- Lowest Average Short Term Temperature 0x05 0x040 1 34 --- Highest Average Long Term Temperature 0x05 0x048 1 23 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 13 --- Specified Minimum Operating Temperature |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS