/dev/sda === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint P120 Device Model: SAMSUNG SP2014N Serial Number: -- Firmware Version: VC100-33 User Capacity: 200,048,565,760 bytes [200 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 4a Local Time is: Wed Jan 17 17:50:03 2018 MSK ==> WARNING: May need -F samsung3 enabled; see manual for details. SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4682) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 78) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 100 100 025 - 5952 4 Start_Stop_Count -O--CK 097 097 000 - 3263 5 Reallocated_Sector_Ct PO--CK 253 253 010 - 0 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 3498 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 002 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1677 190 Airflow_Temperature_Cel -O---K 109 070 000 - 43 194 Temperature_Celsius -O---K 109 070 000 - 43 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 8284969 196 Reallocated_Event_Count -O--CK 253 253 000 - 0 197 Current_Pending_Sector -O--C- 253 100 000 - 0 198 Offline_Uncorrectable ----CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Invalid Error Log index = 0x0000, trying reserved byte (0x08) instead Device Error Count: 1240 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1240 [7] occurred at disk power-on lifetime: 3419 hours (142 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 10 00 00 0e 92 be 2f e0 00 Error: UNC at LBA = 0x0e92be2f = 244497967 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 10 00 00 0e 92 be 2f e0 00 00:51:50.938 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:50.938 READ DMA EXT 42 00 00 00 10 00 00 0e 92 be 1f e0 00 00:51:50.938 READ VERIFY SECTOR(S) EXT Error 1239 [6] occurred at disk power-on lifetime: 3419 hours (142 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 0e 92 be 1f e0 00 Error: UNC at LBA = 0x0e92be1f = 244497951 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 20 00 00 0e 92 be 1f e0 00 00:51:49.063 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:49.063 READ DMA EXT 42 00 00 00 20 00 00 0e 92 bd ff e0 00 00:51:49.063 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:49.063 READ DMA EXT Error 1238 [5] occurred at disk power-on lifetime: 3419 hours (142 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 0e 92 bd ff e0 00 Error: UNC at LBA = 0x0e92bdff = 244497919 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 40 00 00 0e 92 bd ff e0 00 00:51:47.188 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:47.188 READ DMA EXT 42 00 00 00 40 00 00 0e 92 bd bf e0 00 00:51:47.188 READ VERIFY SECTOR(S) EXT Error 1237 [4] occurred at disk power-on lifetime: 3419 hours (142 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 0e 92 bd bf e0 00 Error: UNC at LBA = 0x0e92bdbf = 244497855 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 80 00 00 0e 92 bd bf e0 00 00:51:45.313 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:45.313 READ DMA EXT 42 00 00 00 80 00 00 0e 92 bd 3f e0 00 00:51:45.313 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:45.313 READ DMA EXT Error 1236 [3] occurred at disk power-on lifetime: 3419 hours (142 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 10 00 00 0e 92 be 2f e0 00 Error: UNC at LBA = 0x0e92be2f = 244497967 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 10 00 00 0e 92 be 2f e0 00 00:51:50.938 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:50.938 READ DMA EXT 42 00 00 00 10 00 00 0e 92 be 1f e0 00 00:51:50.938 READ VERIFY SECTOR(S) EXT Error 1235 [2] occurred at disk power-on lifetime: 3419 hours (142 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 0e 92 be 1f e0 00 Error: UNC at LBA = 0x0e92be1f = 244497951 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 20 00 00 0e 92 be 1f e0 00 00:51:49.063 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:49.063 READ DMA EXT 42 00 00 00 20 00 00 0e 92 bd ff e0 00 00:51:49.063 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:49.063 READ DMA EXT Error 1234 [1] occurred at disk power-on lifetime: 3419 hours (142 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 0e 92 bd ff e0 00 Error: UNC at LBA = 0x0e92bdff = 244497919 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 40 00 00 0e 92 bd ff e0 00 00:51:47.188 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:47.188 READ DMA EXT 42 00 00 00 40 00 00 0e 92 bd bf e0 00 00:51:47.188 READ VERIFY SECTOR(S) EXT Error 1233 [0] occurred at disk power-on lifetime: 3419 hours (142 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 0e 92 bd bf e0 00 Error: UNC at LBA = 0x0e92bdbf = 244497855 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 80 00 00 0e 92 bd bf e0 00 00:51:45.313 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:45.313 READ DMA EXT 42 00 00 00 80 00 00 0e 92 bd 3f e0 00 00:51:45.313 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:51:45.313 READ DMA EXT SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported