/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD5000BEVT-22ZAT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500.107.862.016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Jan 28 17:00:44 2016 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13560) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 158) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1091 3 Spin_Up_Time POS--K 185 176 021 - 1750 4 Start_Stop_Count -O--CK 098 098 000 - 2503 5 Reallocated_Sector_Ct PO--CK 199 199 140 - 2 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 094 094 000 - 4686 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2469 192 Power-Off_Retract_Count -O--CK 200 200 000 - 159 193 Load_Cycle_Count -O--CK 198 198 000 - 6637 194 Temperature_Celsius -O---K 116 094 000 - 31 196 Reallocated_Event_Count -O--CK 199 199 000 - 1 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 4499 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4499 [10] occurred at disk power-on lifetime: 2727 hours (113 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 02 00 00 00 00 00 00 00 00 40 00 01:00:08.649 SET FEATURES [Enable write cache] ef 00 03 00 46 00 00 00 00 00 00 40 00 01:00:08.540 SET FEATURES [Set transfer mode] c6 00 00 00 10 00 00 00 00 00 00 40 00 01:00:08.442 SET MULTIPLE MODE 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:00:08.309 READ LOG EXT 60 00 08 00 08 00 00 00 06 b5 30 40 00 01:00:08.198 READ FPDMA QUEUED Error 4498 [9] occurred at disk power-on lifetime: 2727 hours (113 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 40 00 01:00:08.540 SET FEATURES [Set transfer mode] c6 00 00 00 10 00 00 00 00 00 00 40 00 01:00:08.442 SET MULTIPLE MODE 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:00:08.309 READ LOG EXT 60 00 08 00 08 00 00 00 06 b5 30 40 00 01:00:08.198 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 01:00:08.088 SET FEATURES [Enable write cache] Error 4497 [8] occurred at disk power-on lifetime: 2727 hours (113 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 10 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c6 00 00 00 10 00 00 00 00 00 00 40 00 01:00:08.442 SET MULTIPLE MODE 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:00:08.309 READ LOG EXT 60 00 08 00 08 00 00 00 06 b5 30 40 00 01:00:08.198 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 01:00:08.088 SET FEATURES [Enable write cache] ef 00 03 00 46 00 00 00 00 00 00 40 00 01:00:07.980 SET FEATURES [Set transfer mode] Error 4496 [7] occurred at disk power-on lifetime: 2727 hours (113 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 01 00 40 00 00 00 10 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:00:08.309 READ LOG EXT 60 00 08 00 08 00 00 00 06 b5 30 40 00 01:00:08.198 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 01:00:08.088 SET FEATURES [Enable write cache] ef 00 03 00 46 00 00 00 00 00 00 40 00 01:00:07.980 SET FEATURES [Set transfer mode] c6 00 00 00 10 00 00 00 00 00 00 40 00 01:00:07.873 SET MULTIPLE MODE Error 4495 [6] occurred at disk power-on lifetime: 2727 hours (113 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 40 00 00 00 00 40 00 Device Fault; Error: ABRT at LBA = 0x4000000000 = 274877906944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 00 00 06 b5 30 40 00 01:00:08.198 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 01:00:08.088 SET FEATURES [Enable write cache] ef 00 03 00 46 00 00 00 00 00 00 40 00 01:00:07.980 SET FEATURES [Set transfer mode] c6 00 00 00 10 00 00 00 00 00 00 40 00 01:00:07.873 SET MULTIPLE MODE 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:00:07.656 READ LOG EXT Error 4494 [5] occurred at disk power-on lifetime: 2727 hours (113 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 02 00 00 00 00 00 00 00 00 40 00 01:00:08.088 SET FEATURES [Enable write cache] ef 00 03 00 46 00 00 00 00 00 00 40 00 01:00:07.980 SET FEATURES [Set transfer mode] c6 00 00 00 10 00 00 00 00 00 00 40 00 01:00:07.873 SET MULTIPLE MODE 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:00:07.656 READ LOG EXT 61 01 00 00 08 00 00 1a 25 e0 60 40 00 01:00:07.544 WRITE FPDMA QUEUED Error 4493 [4] occurred at disk power-on lifetime: 2727 hours (113 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 40 00 01:00:07.980 SET FEATURES [Set transfer mode] c6 00 00 00 10 00 00 00 00 00 00 40 00 01:00:07.873 SET MULTIPLE MODE 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:00:07.656 READ LOG EXT 61 01 00 00 08 00 00 1a 25 e0 60 40 00 01:00:07.544 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 01:00:07.435 SET FEATURES [Enable write cache] Error 4492 [3] occurred at disk power-on lifetime: 2727 hours (113 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 10 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c6 00 00 00 10 00 00 00 00 00 00 40 00 01:00:07.873 SET MULTIPLE MODE 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:00:07.656 READ LOG EXT 61 01 00 00 08 00 00 1a 25 e0 60 40 00 01:00:07.544 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 40 00 01:00:07.435 SET FEATURES [Enable write cache] ef 00 03 00 46 00 00 00 00 00 00 40 00 01:00:07.327 SET FEATURES [Set transfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 22/31 Celsius Lifetime Min/Max Temperature: 23/54 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (0) Index Estimated Time Temperature Celsius 1 2016-01-28 14:53 42 *********************** 2 2016-01-28 14:54 42 *********************** 3 2016-01-28 14:55 ? - 4 2016-01-28 14:56 40 ********************* ... ..( 19 skipped). .. ********************* 24 2016-01-28 15:16 40 ********************* 25 2016-01-28 15:17 39 ******************** 26 2016-01-28 15:18 40 ********************* 27 2016-01-28 15:19 39 ******************** 28 2016-01-28 15:20 40 ********************* ... ..( 4 skipped). .. ********************* 33 2016-01-28 15:25 40 ********************* 34 2016-01-28 15:26 39 ******************** 35 2016-01-28 15:27 40 ********************* ... ..( 4 skipped). .. ********************* 40 2016-01-28 15:32 40 ********************* 41 2016-01-28 15:33 41 ********************** 42 2016-01-28 15:34 40 ********************* ... ..( 2 skipped). .. ********************* 45 2016-01-28 15:37 40 ********************* 46 2016-01-28 15:38 41 ********************** ... ..( 9 skipped). .. ********************** 56 2016-01-28 15:48 41 ********************** 57 2016-01-28 15:49 40 ********************* 58 2016-01-28 15:50 41 ********************** 59 2016-01-28 15:51 41 ********************** 60 2016-01-28 15:52 42 *********************** 61 2016-01-28 15:53 42 *********************** 62 2016-01-28 15:54 42 *********************** 63 2016-01-28 15:55 41 ********************** 64 2016-01-28 15:56 42 *********************** ... ..( 8 skipped). .. *********************** 73 2016-01-28 16:05 42 *********************** 74 2016-01-28 16:06 41 ********************** 75 2016-01-28 16:07 42 *********************** 76 2016-01-28 16:08 43 ************************ 77 2016-01-28 16:09 42 *********************** ... ..( 10 skipped). .. *********************** 88 2016-01-28 16:20 42 *********************** 89 2016-01-28 16:21 41 ********************** 90 2016-01-28 16:22 42 *********************** ... ..( 9 skipped). .. *********************** 100 2016-01-28 16:32 42 *********************** 101 2016-01-28 16:33 41 ********************** 102 2016-01-28 16:34 41 ********************** 103 2016-01-28 16:35 42 *********************** 104 2016-01-28 16:36 42 *********************** 105 2016-01-28 16:37 43 ************************ ... ..( 2 skipped). .. ************************ 108 2016-01-28 16:40 43 ************************ 109 2016-01-28 16:41 42 *********************** 110 2016-01-28 16:42 42 *********************** 111 2016-01-28 16:43 ? - 112 2016-01-28 16:44 22 *** 113 2016-01-28 16:45 23 **** 114 2016-01-28 16:46 23 **** 115 2016-01-28 16:47 24 ***** 116 2016-01-28 16:48 26 ******* 117 2016-01-28 16:49 26 ******* 118 2016-01-28 16:50 26 ******* 119 2016-01-28 16:51 27 ******** 120 2016-01-28 16:52 27 ******** 121 2016-01-28 16:53 28 ********* 122 2016-01-28 16:54 29 ********** 123 2016-01-28 16:55 30 *********** 124 2016-01-28 16:56 30 *********** 125 2016-01-28 16:57 30 *********** 126 2016-01-28 16:58 31 ************ 127 2016-01-28 16:59 31 ************ 0 2016-01-28 17:00 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x8000 4 997 Vendor specific