/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD5000BEVT-35A0RT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Apr 16 07:47:13 2019 +10 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13560) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 158) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 187 183 021 - 1650 4 Start_Stop_Count -O--CK 091 091 000 - 9026 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 069 069 000 - 23013 10 Spin_Retry_Count -O--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 093 093 000 - 7530 192 Power-Off_Retract_Count -O--CK 200 200 000 - 661 193 Load_Cycle_Count -O--CK 001 001 000 - 1285358 194 Temperature_Celsius -O---K 108 083 000 - 39 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 106 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 106 [9] occurred at disk power-on lifetime: 21450 hours (893 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 38 ff fc 5e 40 00 Error: UNC at LBA = 0x38fffc5e = 956300382 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b8 00 00 38 ff fc 58 40 08 00:18:49.943 READ FPDMA QUEUED 60 00 10 00 b0 00 00 33 fe 16 28 40 08 00:18:49.943 READ FPDMA QUEUED 60 00 08 00 a8 00 00 33 fe 16 10 40 08 00:18:49.943 READ FPDMA QUEUED 60 00 08 00 a0 00 00 33 fe 15 f8 40 08 00:18:49.943 READ FPDMA QUEUED 61 00 10 00 98 00 00 33 dc 50 38 40 08 00:18:49.943 WRITE FPDMA QUEUED Error 105 [8] occurred at disk power-on lifetime: 21450 hours (893 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 38 ff fc 5e 40 00 Error: UNC at LBA = 0x38fffc5e = 956300382 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 d0 00 00 38 ff fc 58 40 08 00:18:46.852 READ FPDMA QUEUED 60 00 08 00 c8 00 00 38 ff fc 50 40 08 00:18:46.852 READ FPDMA QUEUED 60 00 08 00 c0 00 00 38 ff fc 48 40 08 00:18:46.852 READ FPDMA QUEUED 60 00 08 00 b8 00 00 38 ff fc 40 40 08 00:18:46.851 READ FPDMA QUEUED 60 00 08 00 b0 00 00 38 ff fc 38 40 08 00:18:46.851 READ FPDMA QUEUED Error 104 [7] occurred at disk power-on lifetime: 21450 hours (893 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 05 40 00 00 38 ff fc 5e 40 00 Error: UNC at LBA = 0x38fffc5e = 956300382 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 02 c0 00 50 00 00 38 ff fd 40 40 08 00:18:43.435 READ FPDMA QUEUED 60 05 40 00 48 00 00 38 ff f8 00 40 08 00:18:43.435 READ FPDMA QUEUED 60 08 00 00 40 00 00 38 ff f0 00 40 08 00:18:43.400 READ FPDMA QUEUED 60 02 b0 00 38 00 00 38 ff ed 50 40 08 00:18:43.374 READ FPDMA QUEUED 60 05 50 00 30 00 00 38 ff e8 00 40 08 00:18:43.374 READ FPDMA QUEUED Error 103 [6] occurred at disk power-on lifetime: 20506 hours (854 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 00 08 00 00 02 91 6f 76 40 00 Error: AMNF at LBA = 0x02916f76 = 43085686 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 a0 00 00 02 91 6f 70 40 00 00:14:13.676 READ FPDMA QUEUED 61 00 08 00 98 00 00 02 84 d5 50 40 00 00:14:13.676 WRITE FPDMA QUEUED 60 00 38 00 90 00 00 02 90 37 90 40 00 00:14:13.666 READ FPDMA QUEUED 61 00 08 00 88 00 00 02 e3 2b a0 40 00 00:14:13.665 WRITE FPDMA QUEUED 61 00 08 00 80 00 00 0e e4 93 28 40 00 00:14:13.665 WRITE FPDMA QUEUED Error 102 [5] occurred at disk power-on lifetime: 20506 hours (854 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 00 08 00 00 02 91 6f 76 40 00 Error: AMNF at LBA = 0x02916f76 = 43085686 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 c0 00 00 15 64 6b 88 40 00 00:14:10.626 WRITE FPDMA QUEUED 61 01 00 00 b8 00 00 15 64 6a 88 40 00 00:14:10.626 WRITE FPDMA QUEUED 61 00 08 00 b0 00 00 02 a5 d8 08 40 00 00:14:10.626 WRITE FPDMA QUEUED 61 01 00 00 a8 00 00 15 64 69 88 40 00 00:14:10.625 WRITE FPDMA QUEUED 61 01 00 00 a0 00 00 15 64 68 88 40 00 00:14:10.624 WRITE FPDMA QUEUED Error 101 [4] occurred at disk power-on lifetime: 20506 hours (854 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 00 08 00 00 02 91 6f 76 40 00 Error: AMNF at LBA = 0x02916f76 = 43085686 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 a8 00 00 15 64 60 88 40 00 00:14:07.786 WRITE FPDMA QUEUED 61 01 00 00 a0 00 00 15 64 5f 88 40 00 00:14:07.785 WRITE FPDMA QUEUED 61 01 00 00 98 00 00 15 64 5e 88 40 00 00:14:07.785 WRITE FPDMA QUEUED 61 01 00 00 90 00 00 15 64 5d 88 40 00 00:14:07.783 WRITE FPDMA QUEUED 61 01 00 00 88 00 00 15 64 5c 88 40 00 00:14:07.783 WRITE FPDMA QUEUED Error 100 [3] occurred at disk power-on lifetime: 20506 hours (854 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 00 30 00 00 02 91 6f 76 40 00 Error: AMNF at LBA = 0x02916f76 = 43085686 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 18 00 00 0a 8b ef e0 40 00 00:14:04.249 READ FPDMA QUEUED 60 00 30 00 10 00 00 02 91 6f 48 40 00 00:14:04.249 READ FPDMA QUEUED 60 00 28 00 08 00 00 02 f5 fc 80 40 00 00:14:04.249 READ FPDMA QUEUED 61 00 20 00 f8 00 00 14 6b 1f f0 40 00 00:14:04.248 WRITE FPDMA QUEUED 61 00 28 00 f0 00 00 0e e4 92 e0 40 00 00:14:04.248 WRITE FPDMA QUEUED Error 99 [2] occurred at disk power-on lifetime: 20506 hours (854 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 91 6f 76 40 00 Error: UNC at LBA = 0x02916f76 = 43085686 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 c0 00 00 14 07 79 d0 40 00 00:14:00.334 READ FPDMA QUEUED 60 01 00 00 b8 00 00 14 07 78 d0 40 00 00:14:00.334 READ FPDMA QUEUED 60 01 00 00 b0 00 00 14 07 77 d0 40 00 00:14:00.334 READ FPDMA QUEUED 60 00 28 00 a8 00 00 0a 93 6d 48 40 00 00:14:00.334 READ FPDMA QUEUED 61 00 08 00 a0 00 00 02 a5 c1 68 40 00 00:14:00.334 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 22949 - # 2 Short offline Completed without error 00% 4835 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 27/40 Celsius Lifetime Min/Max Temperature: 27/66 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (99) Index Estimated Time Temperature Celsius 100 2019-04-16 05:40 43 ************************ ... ..( 11 skipped). .. ************************ 112 2019-04-16 05:52 43 ************************ 113 2019-04-16 05:53 42 *********************** 114 2019-04-16 05:54 42 *********************** 115 2019-04-16 05:55 43 ************************ 116 2019-04-16 05:56 42 *********************** 117 2019-04-16 05:57 43 ************************ 118 2019-04-16 05:58 42 *********************** ... ..( 2 skipped). .. *********************** 121 2019-04-16 06:01 42 *********************** 122 2019-04-16 06:02 43 ************************ 123 2019-04-16 06:03 42 *********************** ... ..( 3 skipped). .. *********************** 127 2019-04-16 06:07 42 *********************** 0 2019-04-16 06:08 ? - 1 2019-04-16 06:09 27 ******** 2 2019-04-16 06:10 27 ******** 3 2019-04-16 06:11 27 ******** 4 2019-04-16 06:12 28 ********* 5 2019-04-16 06:13 29 ********** 6 2019-04-16 06:14 28 ********* 7 2019-04-16 06:15 29 ********** 8 2019-04-16 06:16 29 ********** 9 2019-04-16 06:17 30 *********** 10 2019-04-16 06:18 30 *********** 11 2019-04-16 06:19 30 *********** 12 2019-04-16 06:20 31 ************ ... ..( 3 skipped). .. ************ 16 2019-04-16 06:24 31 ************ 17 2019-04-16 06:25 32 ************* ... ..( 2 skipped). .. ************* 20 2019-04-16 06:28 32 ************* 21 2019-04-16 06:29 33 ************** 22 2019-04-16 06:30 33 ************** 23 2019-04-16 06:31 33 ************** 24 2019-04-16 06:32 34 *************** ... ..( 3 skipped). .. *************** 28 2019-04-16 06:36 34 *************** 29 2019-04-16 06:37 35 **************** ... ..( 5 skipped). .. **************** 35 2019-04-16 06:43 35 **************** 36 2019-04-16 06:44 36 ***************** 37 2019-04-16 06:45 35 **************** ... ..( 11 skipped). .. **************** 49 2019-04-16 06:57 35 **************** 50 2019-04-16 06:58 36 ***************** ... ..( 29 skipped). .. ***************** 80 2019-04-16 07:28 36 ***************** 81 2019-04-16 07:29 37 ****************** ... ..( 5 skipped). .. ****************** 87 2019-04-16 07:35 37 ****************** 88 2019-04-16 07:36 38 ******************* 89 2019-04-16 07:37 38 ******************* 90 2019-04-16 07:38 39 ******************** 91 2019-04-16 07:39 38 ******************* 92 2019-04-16 07:40 39 ******************** 93 2019-04-16 07:41 39 ******************** 94 2019-04-16 07:42 40 ********************* 95 2019-04-16 07:43 40 ********************* 96 2019-04-16 07:44 40 ********************* 97 2019-04-16 07:45 39 ******************** 98 2019-04-16 07:46 40 ********************* 99 2019-04-16 07:47 39 ******************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 5941 Vendor specific