/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-49-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD5000AAKX-001CA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 15.01H15 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Dec 28 16:20:39 2024 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8700) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 88) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 106 103 051 - 2536534 3 Spin_Up_Time POS--K 139 137 021 - 4008 4 Start_Stop_Count -O--CK 100 100 000 - 134 5 Reallocated_Sector_Ct PO--CK 194 194 140 - 116 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 065 065 000 - 25768 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 129 192 Power-Off_Retract_Count -O--CK 200 200 000 - 98 193 Load_Cycle_Count -O--CK 200 200 000 - 35 194 Temperature_Celsius -O---K 102 085 000 - 41 196 Reallocated_Event_Count -O--CK 142 142 000 - 58 197 Current_Pending_Sector -O--CK 199 199 000 - 112 198 Offline_Uncorrectable ----CK 199 199 000 - 100 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 99 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 46490 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 46490 [9] occurred at disk power-on lifetime: 25739 hours (1072 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1d 52 62 9b 40 00 Error: UNC at LBA = 0x1d52629b = 491938459 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 60 00 00 1d 52 62 98 40 08 15:59:58.086 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 08 15:59:58.086 CHECK POWER MODE ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:59:58.085 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 15:59:58.085 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:59:58.084 IDENTIFY DEVICE Error 46489 [8] occurred at disk power-on lifetime: 25739 hours (1072 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1d 52 62 9b 40 00 Error: UNC at LBA = 0x1d52629b = 491938459 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 a8 00 00 1d 52 62 98 40 08 15:59:57.015 READ FPDMA QUEUED 60 00 08 00 a0 00 00 1d 52 62 90 40 08 15:59:57.015 READ FPDMA QUEUED 60 00 08 00 98 00 00 1d 52 62 88 40 08 15:59:57.015 READ FPDMA QUEUED 60 00 08 00 90 00 00 1d 52 62 80 40 08 15:59:57.015 READ FPDMA QUEUED 60 00 08 00 88 00 00 1d 52 62 78 40 08 15:59:57.014 READ FPDMA QUEUED Error 46488 [7] occurred at disk power-on lifetime: 25733 hours (1072 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 95 30 61 40 00 Error: UNC at LBA = 0x11953061 = 294989921 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 58 00 00 11 95 30 60 40 08 09:22:09.177 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 09:22:09.177 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 09:22:09.177 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 09:22:09.176 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 09:22:09.176 SET FEATURES [Set transfer mode] Error 46487 [6] occurred at disk power-on lifetime: 25733 hours (1072 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 95 30 61 40 00 Error: UNC at LBA = 0x11953061 = 294989921 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 90 00 00 11 95 30 60 40 08 09:22:07.079 READ FPDMA QUEUED 60 00 08 00 88 00 00 11 95 30 58 40 08 09:22:07.078 READ FPDMA QUEUED 60 00 08 00 80 00 00 11 95 30 50 40 08 09:22:07.078 READ FPDMA QUEUED 60 00 08 00 78 00 00 11 95 30 48 40 08 09:22:07.078 READ FPDMA QUEUED 60 00 08 00 70 00 00 11 95 30 40 40 08 09:22:07.077 READ FPDMA QUEUED Error 46486 [5] occurred at disk power-on lifetime: 25733 hours (1072 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 94 0f 3c 40 00 Error: UNC at LBA = 0x11940f3c = 294915900 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 20 00 00 11 94 0f 38 40 08 09:21:56.263 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 09:21:56.262 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 09:21:56.262 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 09:21:56.261 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 09:21:56.261 SET FEATURES [Set transfer mode] Error 46485 [4] occurred at disk power-on lifetime: 25733 hours (1072 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 11 94 0f 3c 40 00 Error: UNC at LBA = 0x11940f3c = 294915900 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 a8 00 00 11 94 0f 38 40 08 09:21:54.819 READ FPDMA QUEUED 60 00 08 00 a0 00 00 11 94 0f 30 40 08 09:21:54.818 READ FPDMA QUEUED 60 00 08 00 98 00 00 11 94 0f 28 40 08 09:21:54.818 READ FPDMA QUEUED 60 00 08 00 90 00 00 11 94 0f 20 40 08 09:21:54.818 READ FPDMA QUEUED 60 00 08 00 88 00 00 11 94 0f 18 40 08 09:21:54.818 READ FPDMA QUEUED Error 46484 [3] occurred at disk power-on lifetime: 25727 hours (1071 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 35 3d a2 40 00 Error: UNC at LBA = 0x01353da2 = 20266402 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 38 00 00 01 35 3d a0 40 08 02:30:35.324 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 02:30:35.324 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 02:30:35.323 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:30:35.322 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 02:30:35.322 SET FEATURES [Set transfer mode] Error 46483 [2] occurred at disk power-on lifetime: 25727 hours (1071 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 35 3d a2 40 00 Error: UNC at LBA = 0x01353da2 = 20266402 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 70 00 00 01 35 3d a0 40 08 02:30:33.582 READ FPDMA QUEUED 60 00 08 00 68 00 00 01 35 3d 98 40 08 02:30:33.582 READ FPDMA QUEUED 60 00 08 00 60 00 00 01 35 3d 90 40 08 02:30:33.582 READ FPDMA QUEUED 60 00 08 00 58 00 00 01 35 3d 88 40 08 02:30:33.582 READ FPDMA QUEUED 60 00 08 00 50 00 00 01 35 3d 80 40 08 02:30:33.582 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 90% 25768 2748138 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 36/40 Celsius Lifetime Min/Max Temperature: 36/58 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (425) Index Estimated Time Temperature Celsius 426 2024-12-28 08:23 45 ************************** ... ..(110 skipped). .. ************************** 59 2024-12-28 10:14 45 ************************** 60 2024-12-28 10:15 46 *************************** ... ..( 5 skipped). .. *************************** 66 2024-12-28 10:21 46 *************************** 67 2024-12-28 10:22 45 ************************** 68 2024-12-28 10:23 46 *************************** ... ..( 4 skipped). .. *************************** 73 2024-12-28 10:28 46 *************************** 74 2024-12-28 10:29 ? - 75 2024-12-28 10:30 36 ***************** 76 2024-12-28 10:31 36 ***************** 77 2024-12-28 10:32 37 ****************** 78 2024-12-28 10:33 37 ****************** 79 2024-12-28 10:34 38 ******************* 80 2024-12-28 10:35 38 ******************* 81 2024-12-28 10:36 39 ******************** 82 2024-12-28 10:37 39 ******************** 83 2024-12-28 10:38 39 ******************** 84 2024-12-28 10:39 40 ********************* ... ..( 6 skipped). .. ********************* 91 2024-12-28 10:46 40 ********************* 92 2024-12-28 10:47 45 ************************** ... ..(323 skipped). .. ************************** 416 2024-12-28 16:11 45 ************************** 417 2024-12-28 16:12 46 *************************** ... ..( 4 skipped). .. *************************** 422 2024-12-28 16:17 46 *************************** 423 2024-12-28 16:18 45 ************************** 424 2024-12-28 16:19 45 ************************** 425 2024-12-28 16:20 45 ************************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 1055 Vendor specific