/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD6400BEVT-22A0RT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 640 135 028 736 bytes [640 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jan 29 16:51:27 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (15960) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 185) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 199 199 051 - 22730 3 Spin_Up_Time POS--K 180 150 021 - 1958 4 Start_Stop_Count -O--CK 018 018 000 - 82249 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 091 091 000 - 6895 10 Spin_Retry_Count -O--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 094 094 000 - 6201 192 Power-Off_Retract_Count -O--CK 198 198 000 - 1844 193 Load_Cycle_Count -O--CK 050 050 000 - 450882 194 Temperature_Celsius -O---K 123 082 000 - 24 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 193 000 - 11 198 Offline_Uncorrectable ----CK 200 200 000 - 9 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 199 051 - 13 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 16550 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 16550 [13] occurred at disk power-on lifetime: 6681 hours (278 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 6f eb d1 40 00 Error: UNC at LBA = 0x006febd1 = 7334865 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 78 00 00 eb 00 6f 00 40 00 01:56:32.541 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 01:56:32.541 SET FEATURES [Enable write cache] 60 01 00 00 68 00 16 c9 00 91 88 40 00 01:56:29.888 READ FPDMA QUEUED 60 00 18 00 60 00 16 ca 00 91 88 40 00 01:56:29.888 READ FPDMA QUEUED 60 01 00 00 58 00 00 eb 00 6f 00 40 00 01:56:29.888 READ FPDMA QUEUED Error 16549 [12] occurred at disk power-on lifetime: 6681 hours (278 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 6f eb d1 40 00 Error: UNC at LBA = 0x006febd1 = 7334865 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 68 00 16 c9 00 91 88 40 00 01:56:29.888 READ FPDMA QUEUED 60 00 18 00 60 00 16 ca 00 91 88 40 00 01:56:29.888 READ FPDMA QUEUED 60 01 00 00 58 00 00 eb 00 6f 00 40 00 01:56:29.888 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 01:56:29.888 SET FEATURES [Enable write cache] 60 00 18 00 50 00 16 ca 00 91 88 40 00 01:56:27.242 READ FPDMA QUEUED Error 16548 [11] occurred at disk power-on lifetime: 6681 hours (278 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 6f eb d1 40 00 Error: UNC at LBA = 0x006febd1 = 7334865 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 18 00 50 00 16 ca 00 91 88 40 00 01:56:27.242 READ FPDMA QUEUED 60 01 00 00 48 00 16 c9 00 91 88 40 00 01:56:27.242 READ FPDMA QUEUED 60 01 00 00 40 00 00 eb 00 6f 00 40 00 01:56:27.234 READ FPDMA QUEUED 60 01 00 00 38 00 17 06 00 02 c8 40 00 01:56:27.223 READ FPDMA QUEUED 60 00 24 00 30 00 17 07 00 02 c8 40 00 01:56:27.203 READ FPDMA QUEUED Error 16547 [10] occurred at disk power-on lifetime: 6681 hours (278 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 6f eb d1 40 00 Error: UNC at LBA = 0x006febd1 = 7334865 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 18 00 17 88 00 02 40 40 00 01:56:24.549 READ FPDMA QUEUED 60 01 00 00 10 00 00 eb 00 6f 00 40 00 01:56:24.549 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 01:56:24.549 SET FEATURES [Enable write cache] 60 00 80 00 08 00 17 88 00 02 40 40 00 01:56:21.887 READ FPDMA QUEUED 60 00 91 00 f8 00 16 61 00 9b 78 40 00 01:56:21.856 READ FPDMA QUEUED Error 16546 [9] occurred at disk power-on lifetime: 6681 hours (278 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 6f eb d1 40 00 Error: UNC at LBA = 0x006febd1 = 7334865 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 08 00 17 88 00 02 40 40 00 01:56:21.887 READ FPDMA QUEUED 60 00 91 00 f8 00 16 61 00 9b 78 40 00 01:56:21.856 READ FPDMA QUEUED 60 01 00 00 f0 00 16 60 00 9b 78 40 00 01:56:21.856 READ FPDMA QUEUED 60 01 00 00 e8 00 16 5f 00 9b 78 40 00 01:56:21.856 READ FPDMA QUEUED 60 01 00 00 e0 00 16 5e 00 9b 78 40 00 01:56:21.856 READ FPDMA QUEUED Error 16545 [8] occurred at disk power-on lifetime: 6681 hours (278 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 6f eb d1 40 00 Error: UNC at LBA = 0x006febd1 = 7334865 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 38 00 00 eb 00 6f 00 40 00 01:56:18.928 READ FPDMA QUEUED 60 01 00 00 30 00 16 cd 00 9a d8 40 00 01:56:18.899 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 01:56:18.899 SET FEATURES [Enable write cache] 60 01 00 00 28 00 16 cd 00 9a d8 40 00 01:56:16.273 READ FPDMA QUEUED 60 01 00 00 20 00 00 eb 00 6f 00 40 00 01:56:16.245 READ FPDMA QUEUED Error 16544 [7] occurred at disk power-on lifetime: 6681 hours (278 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 6f eb d1 40 00 Error: UNC at LBA = 0x006febd1 = 7334865 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 28 00 16 cd 00 9a d8 40 00 01:56:16.273 READ FPDMA QUEUED 60 01 00 00 20 00 00 eb 00 6f 00 40 00 01:56:16.245 READ FPDMA QUEUED 60 01 00 00 18 00 16 cb 00 9a d8 40 00 01:56:16.245 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 01:56:16.245 SET FEATURES [Enable write cache] 60 01 00 00 10 00 16 cd 00 9a d8 40 00 01:56:13.588 READ FPDMA QUEUED Error 16543 [6] occurred at disk power-on lifetime: 6681 hours (278 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 6f eb d1 40 00 Error: UNC at LBA = 0x006febd1 = 7334865 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 10 00 16 cd 00 9a d8 40 00 01:56:13.588 READ FPDMA QUEUED 60 01 00 00 f8 00 16 cc 00 9a d8 40 00 01:56:13.560 READ FPDMA QUEUED 60 01 00 00 08 00 00 eb 00 6f 00 40 00 01:56:13.560 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 01:56:13.560 SET FEATURES [Enable write cache] 60 01 00 00 f0 00 00 eb 00 6f 00 40 00 01:56:10.922 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 24/25 Celsius Lifetime Min/Max Temperature: 24/65 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (54) Index Estimated Time Temperature Celsius 55 2017-01-29 14:44 32 ************* 56 2017-01-29 14:45 32 ************* 57 2017-01-29 14:46 31 ************ ... ..( 2 skipped). .. ************ 60 2017-01-29 14:49 31 ************ 61 2017-01-29 14:50 32 ************* ... ..( 4 skipped). .. ************* 66 2017-01-29 14:55 32 ************* 67 2017-01-29 14:56 31 ************ ... ..( 4 skipped). .. ************ 72 2017-01-29 15:01 31 ************ 73 2017-01-29 15:02 32 ************* 74 2017-01-29 15:03 32 ************* 75 2017-01-29 15:04 32 ************* 76 2017-01-29 15:05 31 ************ ... ..( 78 skipped). .. ************ 27 2017-01-29 16:24 31 ************ 28 2017-01-29 16:25 ? - 29 2017-01-29 16:26 21 ** 30 2017-01-29 16:27 ? - 31 2017-01-29 16:28 22 *** 32 2017-01-29 16:29 21 ** 33 2017-01-29 16:30 21 ** 34 2017-01-29 16:31 23 **** 35 2017-01-29 16:32 24 ***** 36 2017-01-29 16:33 25 ****** 37 2017-01-29 16:34 26 ******* 38 2017-01-29 16:35 26 ******* 39 2017-01-29 16:36 ? - 40 2017-01-29 16:37 27 ******** 41 2017-01-29 16:38 ? - 42 2017-01-29 16:39 25 ****** 43 2017-01-29 16:40 ? - 44 2017-01-29 16:41 25 ****** 45 2017-01-29 16:42 24 ***** 46 2017-01-29 16:43 24 ***** 47 2017-01-29 16:44 25 ****** 48 2017-01-29 16:45 24 ***** ... ..( 3 skipped). .. ***** 52 2017-01-29 16:49 24 ***** 53 2017-01-29 16:50 ? - 54 2017-01-29 16:51 25 ****** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 554 Vendor specific /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST3500418AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC49 User Capacity: 500 107 862 016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jan 29 16:51:27 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 82) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 100 006 - 141479814 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1906 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 065 060 030 - 3467517 9 Power_On_Hours -O--CK 100 100 000 - 420 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 857 183 Runtime_Bad_Block ------ 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 092 000 - 679 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 072 056 045 - 28 (Min/Max 21/28) 194 Temperature_Celsius -O---K 028 044 000 - 28 (0 17 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 041 033 000 - 141479814 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 2084 (242 229 0) 241 Total_LBAs_Written ------ 100 253 000 - 1536770495 242 Total_LBAs_Read ------ 100 253 000 - 1751711445 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 21/27 Celsius Lifetime Min/Max Temperature: 17/44 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (71) Index Estimated Time Temperature Celsius 72 2017-01-24 11:17 19 - 73 2017-01-24 12:16 34 *************** 74 2017-01-24 13:15 36 ***************** 75 2017-01-24 14:14 37 ****************** 76 2017-01-24 15:13 36 ***************** 77 2017-01-24 16:12 36 ***************** 78 2017-01-24 17:11 35 **************** 79 2017-01-24 18:10 ? - 80 2017-01-24 19:09 20 * 81 2017-01-24 20:08 ? - 82 2017-01-24 21:07 20 * 83 2017-01-24 22:06 ? - 84 2017-01-24 23:05 25 ****** 85 2017-01-25 00:04 ? - 86 2017-01-25 01:03 17 - 87 2017-01-25 02:02 ? - 88 2017-01-25 03:01 17 - 89 2017-01-25 04:00 ? - 90 2017-01-25 04:59 17 - 91 2017-01-25 05:58 ? - 92 2017-01-25 06:57 17 - 93 2017-01-25 07:56 17 - 94 2017-01-25 08:55 33 ************** 95 2017-01-25 09:54 ? - 96 2017-01-25 10:53 18 - 97 2017-01-25 11:52 ? - 98 2017-01-25 12:51 18 - 99 2017-01-25 13:50 ? - 100 2017-01-25 14:49 19 - 101 2017-01-25 15:48 ? - 102 2017-01-25 16:47 20 * 103 2017-01-25 17:46 ? - 104 2017-01-25 18:45 18 - 105 2017-01-25 19:44 ? - 106 2017-01-25 20:43 19 - 107 2017-01-25 21:42 ? - 108 2017-01-25 22:41 18 - 109 2017-01-25 23:40 ? - 110 2017-01-26 00:39 18 - 111 2017-01-26 01:38 ? - 112 2017-01-26 02:37 18 - 113 2017-01-26 03:36 ? - 114 2017-01-26 04:35 18 - 115 2017-01-26 05:34 ? - 116 2017-01-26 06:33 23 **** 117 2017-01-26 07:32 23 **** 118 2017-01-26 08:31 33 ************** 119 2017-01-26 09:30 ? - 120 2017-01-26 10:29 23 **** 121 2017-01-26 11:28 ? - 122 2017-01-26 12:27 23 **** 123 2017-01-26 13:26 ? - 124 2017-01-26 14:25 18 - 125 2017-01-26 15:24 ? - 126 2017-01-26 16:23 18 - 127 2017-01-26 17:22 18 - 0 2017-01-26 18:21 ? - 1 2017-01-26 19:20 21 ** 2 2017-01-26 20:19 ? - 3 2017-01-26 21:18 21 ** 4 2017-01-26 22:17 ? - 5 2017-01-26 23:16 21 ** 6 2017-01-27 00:15 ? - 7 2017-01-27 01:14 21 ** 8 2017-01-27 02:13 ? - 9 2017-01-27 03:12 18 - 10 2017-01-27 04:11 ? - 11 2017-01-27 05:10 18 - 12 2017-01-27 06:09 ? - 13 2017-01-27 07:08 18 - 14 2017-01-27 08:07 ? - 15 2017-01-27 09:06 18 - 16 2017-01-27 10:05 ? - 17 2017-01-27 11:04 19 - 18 2017-01-27 12:03 ? - 19 2017-01-27 13:02 19 - 20 2017-01-27 14:01 ? - 21 2017-01-27 15:00 18 - 22 2017-01-27 15:59 ? - 23 2017-01-27 16:58 18 - 24 2017-01-27 17:57 ? - 25 2017-01-27 18:56 19 - 26 2017-01-27 19:55 ? - 27 2017-01-27 20:54 19 - 28 2017-01-27 21:53 ? - 29 2017-01-27 22:52 17 - 30 2017-01-27 23:51 ? - 31 2017-01-28 00:50 17 - 32 2017-01-28 01:49 17 - 33 2017-01-28 02:48 ? - 34 2017-01-28 03:47 17 - 35 2017-01-28 04:46 ? - 36 2017-01-28 05:45 17 - 37 2017-01-28 06:44 17 - 38 2017-01-28 07:43 ? - 39 2017-01-28 08:42 17 - 40 2017-01-28 09:41 ? - 41 2017-01-28 10:40 18 - 42 2017-01-28 11:39 ? - 43 2017-01-28 12:38 19 - 44 2017-01-28 13:37 ? - 45 2017-01-28 14:36 19 - 46 2017-01-28 15:35 ? - 47 2017-01-28 16:34 19 - 48 2017-01-28 17:33 ? - 49 2017-01-28 18:32 19 - 50 2017-01-28 19:31 ? - 51 2017-01-28 20:30 17 - 52 2017-01-28 21:29 ? - 53 2017-01-28 22:28 17 - 54 2017-01-28 23:27 17 - 55 2017-01-29 00:26 33 ************** 56 2017-01-29 01:25 34 *************** 57 2017-01-29 02:24 ? - 58 2017-01-29 03:23 18 - 59 2017-01-29 04:22 ? - 60 2017-01-29 05:21 18 - 61 2017-01-29 06:20 ? - 62 2017-01-29 07:19 18 - 63 2017-01-29 08:18 ? - 64 2017-01-29 09:17 18 - 65 2017-01-29 10:16 18 - 66 2017-01-29 11:15 33 ************** 67 2017-01-29 12:14 ? - 68 2017-01-29 13:13 21 ** 69 2017-01-29 14:12 ? - 70 2017-01-29 15:11 21 ** 71 2017-01-29 16:10 21 ** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc === START OF INFORMATION SECTION === Device Model: TOSHIBA HDWD110 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MS2OA8J0 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jan 29 16:51:27 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7070) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 118) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 142 142 054 - 69 3 Spin_Up_Time POS--- 122 122 024 - 187 (Average 188) 4 Start_Stop_Count -O--C- 100 100 000 - 139 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 113 113 020 - 35 9 Power_On_Hours -O--C- 100 100 000 - 236 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 134 192 Power-Off_Retract_Count -O--CK 100 100 000 - 140 193 Load_Cycle_Count -O--C- 100 100 000 - 140 194 Temperature_Celsius -O---- 214 214 000 - 28 (Min/Max 20/36) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 24/28 Celsius Lifetime Min/Max Temperature: 20/36 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (13) Index Estimated Time Temperature Celsius 14 2017-01-29 14:44 31 ************ ... ..( 2 skipped). .. ************ 17 2017-01-29 14:47 31 ************ 18 2017-01-29 14:48 32 ************* 19 2017-01-29 14:49 32 ************* 20 2017-01-29 14:50 32 ************* 21 2017-01-29 14:51 33 ************** ... ..( 11 skipped). .. ************** 33 2017-01-29 15:03 33 ************** 34 2017-01-29 15:04 32 ************* ... ..( 7 skipped). .. ************* 42 2017-01-29 15:12 32 ************* 43 2017-01-29 15:13 33 ************** ... ..( 7 skipped). .. ************** 51 2017-01-29 15:21 33 ************** 52 2017-01-29 15:22 32 ************* 53 2017-01-29 15:23 32 ************* 54 2017-01-29 15:24 33 ************** 55 2017-01-29 15:25 32 ************* ... ..( 6 skipped). .. ************* 62 2017-01-29 15:32 32 ************* 63 2017-01-29 15:33 33 ************** ... ..( 21 skipped). .. ************** 85 2017-01-29 15:55 33 ************** 86 2017-01-29 15:56 34 *************** 87 2017-01-29 15:57 34 *************** 88 2017-01-29 15:58 33 ************** ... ..( 15 skipped). .. ************** 104 2017-01-29 16:14 33 ************** 105 2017-01-29 16:15 34 *************** ... ..( 3 skipped). .. *************** 109 2017-01-29 16:19 34 *************** 110 2017-01-29 16:20 33 ************** ... ..( 12 skipped). .. ************** 123 2017-01-29 16:33 33 ************** 124 2017-01-29 16:34 34 *************** ... ..( 6 skipped). .. *************** 3 2017-01-29 16:41 34 *************** 4 2017-01-29 16:42 ? - 5 2017-01-29 16:43 25 ****** 6 2017-01-29 16:44 25 ****** 7 2017-01-29 16:45 26 ******* 8 2017-01-29 16:46 26 ******* 9 2017-01-29 16:47 27 ******** 10 2017-01-29 16:48 27 ******** 11 2017-01-29 16:49 28 ********* 12 2017-01-29 16:50 28 ********* 13 2017-01-29 16:51 28 ********* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 134 --- Lifetime Power-On Resets 0x01 0x010 4 236 --- Power-on Hours 0x01 0x018 6 1864769461 --- Logical Sectors Written 0x01 0x020 6 18822650 --- Number of Write Commands 0x01 0x028 6 8964102232 --- Logical Sectors Read 0x01 0x030 6 13019735 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 233 --- Spindle Motor Power-on Hours 0x03 0x010 4 233 --- Head Flying Hours 0x03 0x018 4 140 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 1 --- Read Recovery Attempts 0x03 0x030 4 2 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 29 --- Current Temperature 0x05 0x010 1 31 N-- Average Short Term Temperature 0x05 0x018 1 31 N-- Average Long Term Temperature 0x05 0x020 1 36 --- Highest Temperature 0x05 0x028 1 20 --- Lowest Temperature 0x05 0x030 1 33 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 32 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 332 --- Number of Hardware Resets 0x06 0x010 4 198 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdd === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3320620AS Serial Number: -- Firmware Version: 3.AAC User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sun Jan 29 16:51:30 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 115) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 118 090 006 - 184945505 3 Spin_Up_Time PO---- 091 089 000 - 0 4 Start_Stop_Count -O--CK 093 093 020 - 7265 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 088 060 030 - 757079771 9 Power_On_Hours -O--CK 082 082 000 - 16191 10 Spin_Retry_Count PO--C- 100 099 097 - 0 12 Power_Cycle_Count -O--CK 093 093 020 - 7908 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 067 030 045 Past 33 (211 194 33 24 0) 194 Temperature_Celsius -O---K 033 070 000 - 33 (0 10 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 083 049 000 - 147383687 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS