/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Maxtor DiamondMax 23 Device Model: STM3250318AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC44 User Capacity: 250 059 350 016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Dec 8 09:55:15 2017 +04 ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213911en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 634) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 53) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 118 099 006 - 189743406 3 Spin_Up_Time PO---- 098 097 000 - 0 4 Start_Stop_Count -O--CK 098 098 020 - 2146 5 Reallocated_Sector_Ct PO--CK 099 099 036 - 72 7 Seek_Error_Rate POSR-- 064 060 030 - 365289409420 9 Power_On_Hours -O--CK 091 091 000 - 8175 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 098 098 020 - 2163 183 Runtime_Bad_Block ------ 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 097 000 - 8590196824 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 070 054 045 - 30 (Min/Max 15/30) 194 Temperature_Celsius -O---K 030 046 000 - 30 (0 8 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 052 039 000 - 189743406 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 14040 (50 220 0) 241 Total_LBAs_Written ------ 100 253 000 - 27808229 242 Total_LBAs_Read ------ 100 253 000 - 540062705 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL,SL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 113 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 113 [12] occurred at disk power-on lifetime: 2209 hours (92 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 01 00 32 80 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- a1 00 00 00 03 00 00 01 00 32 80 a0 00 02:36:23.924 IDENTIFY PACKET DEVICE ec 00 00 00 01 00 00 00 00 00 01 a0 00 02:36:23.388 IDENTIFY DEVICE 00 00 00 00 00 00 00 00 00 00 00 00 04 02:36:23.288 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 ff 02:36:16.475 NOP [Abort queued commands] a1 00 00 00 03 00 00 01 00 32 80 a0 00 02:35:14.512 IDENTIFY PACKET DEVICE Error 112 [11] occurred at disk power-on lifetime: 2209 hours (92 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 01 00 32 80 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 01 00 00 00 00 00 01 a0 00 02:36:23.388 IDENTIFY DEVICE 00 00 00 00 00 00 00 00 00 00 00 00 04 02:36:23.288 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 ff 02:36:16.475 NOP [Abort queued commands] a1 00 00 00 03 00 00 01 00 32 80 a0 00 02:35:14.512 IDENTIFY PACKET DEVICE ec 00 00 00 01 00 00 00 00 00 01 a0 00 02:35:13.976 IDENTIFY DEVICE Error 111 [10] occurred at disk power-on lifetime: 2209 hours (92 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 01 00 32 80 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- a1 00 00 00 03 00 00 01 00 32 80 a0 00 02:35:14.512 IDENTIFY PACKET DEVICE ec 00 00 00 01 00 00 00 00 00 01 a0 00 02:35:13.976 IDENTIFY DEVICE 00 00 00 00 00 00 00 00 00 00 00 00 04 02:35:13.876 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 ff 02:35:07.061 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 04 02:34:55.215 NOP [Abort queued commands] Error 110 [9] occurred at disk power-on lifetime: 2209 hours (92 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 01 00 32 80 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 01 00 00 00 00 00 01 a0 00 02:35:13.976 IDENTIFY DEVICE 00 00 00 00 00 00 00 00 00 00 00 00 04 02:35:13.876 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 ff 02:35:07.061 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 04 02:34:55.215 NOP [Abort queued commands] c6 00 00 00 00 00 00 01 00 32 80 a0 00 02:34:55.195 SET MULTIPLE MODE Error 109 [8] occurred at disk power-on lifetime: 2209 hours (92 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 01 00 32 80 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c6 00 00 00 00 00 00 01 00 32 80 a0 00 02:34:55.195 SET MULTIPLE MODE 34 00 00 00 01 00 05 b9 00 db e7 e0 00 02:34:55.195 WRITE SECTORS(S) EXT c6 00 00 00 00 00 00 01 00 32 80 a0 00 02:34:55.129 SET MULTIPLE MODE 34 00 00 00 01 00 05 b9 00 db e7 e0 00 02:34:55.129 WRITE SECTORS(S) EXT 00 00 00 00 00 00 00 00 00 00 00 00 04 02:34:55.089 NOP [Abort queued commands] Error 108 [7] occurred at disk power-on lifetime: 2209 hours (92 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 01 00 32 80 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c6 00 00 00 00 00 00 01 00 32 80 a0 00 02:34:55.129 SET MULTIPLE MODE 34 00 00 00 01 00 05 b9 00 db e7 e0 00 02:34:55.129 WRITE SECTORS(S) EXT 00 00 00 00 00 00 00 00 00 00 00 00 04 02:34:55.089 NOP [Abort queued commands] c6 00 00 00 00 00 00 01 00 32 80 a0 00 02:34:55.029 SET MULTIPLE MODE 34 00 00 00 01 00 05 b9 00 db e7 e0 00 02:34:55.029 WRITE SECTORS(S) EXT Error 107 [6] occurred at disk power-on lifetime: 2209 hours (92 days + 1 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 01 00 32 80 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 04 02:34:55.089 NOP [Abort queued commands] c6 00 00 00 00 00 00 01 00 32 80 a0 00 02:34:55.029 SET MULTIPLE MODE 34 00 00 00 01 00 05 b9 00 db e7 e0 00 02:34:55.029 WRITE SECTORS(S) EXT c6 00 00 00 00 00 00 01 00 32 80 a0 00 02:34:54.954 SET MULTIPLE MODE 34 00 00 00 01 00 05 b9 00 db e7 e0 00 02:34:54.954 WRITE SECTORS(S) EXT Error 106 [5] occurred at disk power-on lifetime: 2209 hours (92 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 01 00 32 80 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c6 00 00 00 00 00 00 01 00 32 80 a0 00 02:34:55.029 SET MULTIPLE MODE 34 00 00 00 01 00 05 b9 00 db e7 e0 00 02:34:55.029 WRITE SECTORS(S) EXT c6 00 00 00 00 00 00 01 00 32 80 a0 00 02:34:54.954 SET MULTIPLE MODE 34 00 00 00 01 00 05 b9 00 db e7 e0 00 02:34:54.954 WRITE SECTORS(S) EXT 00 00 00 00 00 00 00 00 00 00 00 00 04 02:34:54.914 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 15/30 Celsius Lifetime Min/Max Temperature: 8/46 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (112) Index Estimated Time Temperature Celsius 113 2017-12-03 04:08 ? - 114 2017-12-03 05:07 17 - 115 2017-12-03 06:06 17 - 116 2017-12-03 07:05 32 ************* 117 2017-12-03 08:04 35 **************** 118 2017-12-03 09:03 36 ***************** 119 2017-12-03 10:02 36 ***************** 120 2017-12-03 11:01 35 **************** 121 2017-12-03 12:00 37 ****************** 122 2017-12-03 12:59 35 **************** 123 2017-12-03 13:58 ? - 124 2017-12-03 14:57 17 - 125 2017-12-03 15:56 17 - 126 2017-12-03 16:55 32 ************* 127 2017-12-03 17:54 33 ************** 0 2017-12-03 18:53 34 *************** 1 2017-12-03 19:52 34 *************** 2 2017-12-03 20:51 34 *************** 3 2017-12-03 21:50 33 ************** 4 2017-12-03 22:49 33 ************** 5 2017-12-03 23:48 ? - 6 2017-12-04 00:47 17 - 7 2017-12-04 01:46 17 - 8 2017-12-04 02:45 ? - 9 2017-12-04 03:44 21 ** 10 2017-12-04 04:43 ? - 11 2017-12-04 05:42 16 - 12 2017-12-04 06:41 16 - 13 2017-12-04 07:40 31 ************ 14 2017-12-04 08:39 32 ************* 15 2017-12-04 09:38 34 *************** 16 2017-12-04 10:37 35 **************** 17 2017-12-04 11:36 33 ************** 18 2017-12-04 12:35 ? - 19 2017-12-04 13:34 14 - 20 2017-12-04 14:33 14 - 21 2017-12-04 15:32 30 *********** 22 2017-12-04 16:31 31 ************ 23 2017-12-04 17:30 32 ************* 24 2017-12-04 18:29 32 ************* 25 2017-12-04 19:28 33 ************** 26 2017-12-04 20:27 32 ************* 27 2017-12-04 21:26 ? - 28 2017-12-04 22:25 15 - 29 2017-12-04 23:24 15 - 30 2017-12-05 00:23 31 ************ 31 2017-12-05 01:22 33 ************** ... ..( 4 skipped). .. ************** 36 2017-12-05 06:17 33 ************** 37 2017-12-05 07:16 ? - 38 2017-12-05 08:15 14 - 39 2017-12-05 09:14 14 - 40 2017-12-05 10:13 31 ************ 41 2017-12-05 11:12 32 ************* 42 2017-12-05 12:11 33 ************** 43 2017-12-05 13:10 33 ************** 44 2017-12-05 14:09 33 ************** 45 2017-12-05 15:08 ? - 46 2017-12-05 16:07 18 - 47 2017-12-05 17:06 18 - 48 2017-12-05 18:05 33 ************** 49 2017-12-05 19:04 33 ************** 50 2017-12-05 20:03 ? - 51 2017-12-05 21:02 14 - 52 2017-12-05 22:01 14 - 53 2017-12-05 23:00 30 *********** 54 2017-12-05 23:59 32 ************* 55 2017-12-06 00:58 33 ************** 56 2017-12-06 01:57 33 ************** 57 2017-12-06 02:56 34 *************** 58 2017-12-06 03:55 ? - 59 2017-12-06 04:54 13 - 60 2017-12-06 05:53 13 - 61 2017-12-06 06:52 30 *********** 62 2017-12-06 07:51 31 ************ 63 2017-12-06 08:50 32 ************* 64 2017-12-06 09:49 34 *************** 65 2017-12-06 10:48 34 *************** 66 2017-12-06 11:47 34 *************** 67 2017-12-06 12:46 ? - 68 2017-12-06 13:45 14 - 69 2017-12-06 14:44 14 - 70 2017-12-06 15:43 31 ************ 71 2017-12-06 16:42 33 ************** 72 2017-12-06 17:41 35 **************** 73 2017-12-06 18:40 35 **************** 74 2017-12-06 19:39 34 *************** 75 2017-12-06 20:38 35 **************** 76 2017-12-06 21:37 35 **************** 77 2017-12-06 22:36 ? - 78 2017-12-06 23:35 21 ** 79 2017-12-07 00:34 21 ** 80 2017-12-07 01:33 34 *************** 81 2017-12-07 02:32 35 **************** 82 2017-12-07 03:31 37 ****************** 83 2017-12-07 04:30 35 **************** 84 2017-12-07 05:29 ? - 85 2017-12-07 06:28 34 *************** 86 2017-12-07 07:27 ? - 87 2017-12-07 08:26 33 ************** 88 2017-12-07 09:25 33 ************** 89 2017-12-07 10:24 ? - 90 2017-12-07 11:23 24 ***** 91 2017-12-07 12:22 ? - 92 2017-12-07 13:21 41 ********************** 93 2017-12-07 14:20 ? - 94 2017-12-07 15:19 24 ***** 95 2017-12-07 16:18 24 ***** 96 2017-12-07 17:17 ? - 97 2017-12-07 18:16 19 - 98 2017-12-07 19:15 ? - 99 2017-12-07 20:14 20 * 100 2017-12-07 21:13 20 * 101 2017-12-07 22:12 ? - 102 2017-12-07 23:11 31 ************ 103 2017-12-08 00:10 ? - 104 2017-12-08 01:09 31 ************ 105 2017-12-08 02:08 31 ************ 106 2017-12-08 03:07 33 ************** 107 2017-12-08 04:06 ? - 108 2017-12-08 05:05 20 * 109 2017-12-08 06:04 ? - 110 2017-12-08 07:03 15 - 111 2017-12-08 08:02 15 - 112 2017-12-08 09:01 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS