/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD3200BEVT-22A23T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat May 9 12:26:24 2015 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7560) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 91) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 31 3 Spin_Up_Time POS--K 152 130 021 - 1400 4 Start_Stop_Count -O--CK 074 074 000 - 26819 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 081 081 000 - 14076 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5151 191 G-Sense_Error_Rate -O--CK 001 001 000 - 10059 192 Power-Off_Retract_Count -O--CK 200 200 000 - 325 193 Load_Cycle_Count -O--CK 001 001 000 - 598210 194 Temperature_Celsius -O---K 108 094 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 10 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 [9] occurred at disk power-on lifetime: 10233 hours (426 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 03 93 92 56 40 00 Error: UNC at LBA = 0x03939256 = 60002902 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 d0 00 00 03 93 96 40 40 00 00:52:59.268 READ FPDMA QUEUED 60 01 00 00 c8 00 00 03 93 95 40 40 00 00:52:59.268 READ FPDMA QUEUED 60 01 00 00 c0 00 00 03 93 94 40 40 00 00:52:59.268 READ FPDMA QUEUED 60 01 00 00 b8 00 00 03 93 93 40 40 00 00:52:59.244 READ FPDMA QUEUED 60 01 00 00 b0 00 00 03 93 92 40 40 00 00:52:59.242 READ FPDMA QUEUED Error 9 [8] occurred at disk power-on lifetime: 10200 hours (425 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 03 93 92 56 40 00 Error: WP at LBA = 0x03939256 = 60002902 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 30 00 00 00 08 95 c8 40 00 00:19:20.583 WRITE FPDMA QUEUED 61 00 0b 00 18 00 00 03 69 8d 88 40 00 00:19:20.583 WRITE FPDMA QUEUED 61 00 58 00 08 00 00 00 61 04 60 40 00 00:19:20.583 WRITE FPDMA QUEUED 60 00 20 00 58 00 00 00 47 2f 60 40 00 00:19:20.583 READ FPDMA QUEUED 60 00 20 00 50 00 00 00 12 20 40 40 00 00:19:20.583 READ FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 10200 hours (425 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 03 93 92 56 40 00 Error: WP at LBA = 0x03939256 = 60002902 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 c5 00 b8 00 00 00 1f d2 00 40 00 00:19:17.829 WRITE FPDMA QUEUED 61 01 00 00 b0 00 00 00 1f d1 00 40 00 00:19:17.828 WRITE FPDMA QUEUED 61 01 00 00 a8 00 00 00 1f d0 00 40 00 00:19:17.827 WRITE FPDMA QUEUED 61 01 00 00 a0 00 00 00 1f cf 00 40 00 00:19:17.827 WRITE FPDMA QUEUED 61 01 00 00 98 00 00 00 1f ce 00 40 00 00:19:17.825 WRITE FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 10200 hours (425 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 03 93 92 56 40 00 Error: UNC at LBA = 0x03939256 = 60002902 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b0 00 00 03 93 92 40 40 00 00:19:15.251 READ FPDMA QUEUED 60 00 40 00 a8 00 00 03 93 92 40 40 00 00:19:15.250 READ FPDMA QUEUED 60 00 08 00 a0 00 00 03 93 92 00 40 00 00:19:15.250 READ FPDMA QUEUED 60 00 40 00 98 00 00 03 93 92 00 40 00 00:19:15.250 READ FPDMA QUEUED 60 00 08 00 90 00 00 03 93 91 c0 40 00 00:19:15.249 READ FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 10177 hours (424 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 03 93 92 56 40 00 Error: WP at LBA = 0x03939256 = 60002902 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 c8 00 00 00 03 2e 38 40 00 00:01:43.139 WRITE FPDMA QUEUED 61 00 10 00 b8 00 00 00 63 20 f8 40 00 00:01:43.138 WRITE FPDMA QUEUED 61 00 10 00 b0 00 00 00 06 6b c8 40 00 00:01:43.138 WRITE FPDMA QUEUED 61 00 02 00 88 00 00 00 1a 98 b0 40 00 00:01:43.138 WRITE FPDMA QUEUED 61 00 08 00 d0 00 00 00 5f 1b 88 40 00 00:01:43.138 WRITE FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 10177 hours (424 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 03 93 92 56 40 00 Error: WP at LBA = 0x03939256 = 60002902 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 b0 00 00 00 63 e5 30 40 00 00:01:39.903 WRITE FPDMA QUEUED 61 00 08 00 e0 00 00 00 5f 1b 88 40 00 00:01:39.903 WRITE FPDMA QUEUED 61 00 08 00 b0 00 00 00 63 e4 b8 40 00 00:01:39.903 WRITE FPDMA QUEUED 61 00 10 00 e0 00 00 00 60 e9 98 40 00 00:01:39.903 WRITE FPDMA QUEUED 61 00 08 00 b0 00 00 00 63 e4 90 40 00 00:01:39.903 WRITE FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 10177 hours (424 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 03 93 92 56 40 00 Error: WP at LBA = 0x03939256 = 60002902 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 88 00 00 00 5f 1b 88 40 00 00:01:36.500 WRITE FPDMA QUEUED 61 00 38 00 88 00 00 00 60 e9 28 40 00 00:01:36.500 WRITE FPDMA QUEUED 61 00 18 00 88 00 00 00 03 4b c8 40 00 00:01:36.498 WRITE FPDMA QUEUED 60 00 08 00 88 00 00 00 07 0e 50 40 00 00:01:36.496 READ FPDMA QUEUED 60 00 08 00 58 00 00 04 49 bd 48 40 00 00:01:36.491 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 10177 hours (424 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 03 93 92 59 40 00 Error: WP at LBA = 0x03939259 = 60002905 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 50 00 00 00 63 b6 08 40 00 00:01:29.502 WRITE FPDMA QUEUED 61 00 e7 00 48 00 00 00 28 e4 10 40 00 00:01:29.501 WRITE FPDMA QUEUED 61 01 00 00 40 00 00 00 28 e3 10 40 00 00:01:29.501 WRITE FPDMA QUEUED 61 00 08 00 38 00 00 00 5f 1b 88 40 00 00:01:29.501 WRITE FPDMA QUEUED 61 00 08 00 30 00 00 00 63 b5 f0 40 00 00:01:29.501 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 22/36 Celsius Lifetime Min/Max Temperature: 35/53 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (45) Index Estimated Time Temperature Celsius 46 2015-05-09 10:19 24 ***** 47 2015-05-09 10:20 24 ***** 48 2015-05-09 10:21 25 ****** 49 2015-05-09 10:22 25 ****** 50 2015-05-09 10:23 ? - 51 2015-05-09 10:24 26 ******* 52 2015-05-09 10:25 ? - 53 2015-05-09 10:26 27 ******** 54 2015-05-09 10:27 26 ******* 55 2015-05-09 10:28 ? - 56 2015-05-09 10:29 27 ******** 57 2015-05-09 10:30 26 ******* 58 2015-05-09 10:31 ? - 59 2015-05-09 10:32 27 ******** ... ..( 2 skipped). .. ******** 62 2015-05-09 10:35 27 ******** 63 2015-05-09 10:36 ? - 64 2015-05-09 10:37 28 ********* 65 2015-05-09 10:38 28 ********* 66 2015-05-09 10:39 ? - 67 2015-05-09 10:40 28 ********* ... ..( 2 skipped). .. ********* 70 2015-05-09 10:43 28 ********* 71 2015-05-09 10:44 ? - 72 2015-05-09 10:45 28 ********* 73 2015-05-09 10:46 ? - 74 2015-05-09 10:47 29 ********** 75 2015-05-09 10:48 28 ********* 76 2015-05-09 10:49 29 ********** 77 2015-05-09 10:50 ? - 78 2015-05-09 10:51 29 ********** 79 2015-05-09 10:52 29 ********** 80 2015-05-09 10:53 ? - 81 2015-05-09 10:54 29 ********** 82 2015-05-09 10:55 ? - 83 2015-05-09 10:56 29 ********** 84 2015-05-09 10:57 29 ********** 85 2015-05-09 10:58 ? - 86 2015-05-09 10:59 30 *********** 87 2015-05-09 11:00 ? - 88 2015-05-09 11:01 30 *********** 89 2015-05-09 11:02 29 ********** 90 2015-05-09 11:03 ? - 91 2015-05-09 11:04 30 *********** 92 2015-05-09 11:05 ? - 93 2015-05-09 11:06 30 *********** 94 2015-05-09 11:07 30 *********** 95 2015-05-09 11:08 ? - 96 2015-05-09 11:09 30 *********** 97 2015-05-09 11:10 30 *********** 98 2015-05-09 11:11 30 *********** 99 2015-05-09 11:12 ? - 100 2015-05-09 11:13 31 ************ 101 2015-05-09 11:14 30 *********** 102 2015-05-09 11:15 30 *********** 103 2015-05-09 11:16 31 ************ ... ..( 5 skipped). .. ************ 109 2015-05-09 11:22 31 ************ 110 2015-05-09 11:23 32 ************* ... ..( 4 skipped). .. ************* 115 2015-05-09 11:28 32 ************* 116 2015-05-09 11:29 33 ************** 117 2015-05-09 11:30 33 ************** 118 2015-05-09 11:31 33 ************** 119 2015-05-09 11:32 34 *************** 120 2015-05-09 11:33 34 *************** 121 2015-05-09 11:34 34 *************** 122 2015-05-09 11:35 35 **************** 123 2015-05-09 11:36 34 *************** 124 2015-05-09 11:37 35 **************** 125 2015-05-09 11:38 35 **************** 126 2015-05-09 11:39 35 **************** 127 2015-05-09 11:40 34 *************** 0 2015-05-09 11:41 35 **************** ... ..( 25 skipped). .. **************** 26 2015-05-09 12:07 35 **************** 27 2015-05-09 12:08 36 ***************** 28 2015-05-09 12:09 35 **************** ... ..( 2 skipped). .. **************** 31 2015-05-09 12:12 35 **************** 32 2015-05-09 12:13 36 ***************** 33 2015-05-09 12:14 35 **************** 34 2015-05-09 12:15 36 ***************** 35 2015-05-09 12:16 36 ***************** 36 2015-05-09 12:17 35 **************** 37 2015-05-09 12:18 36 ***************** ... ..( 2 skipped). .. ***************** 40 2015-05-09 12:21 36 ***************** 41 2015-05-09 12:22 35 **************** 42 2015-05-09 12:23 35 **************** 43 2015-05-09 12:24 36 ***************** 44 2015-05-09 12:25 35 **************** 45 2015-05-09 12:26 35 **************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 5759 Vendor specific