/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.6.51-1.red80.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SAMSUNG HD081GJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: GE100-07 User Capacity: 80,026,361,856 bytes [80.0 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database 7.3/5577 ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Jan 9 08:40:56 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1320) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 22) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 18 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 073 073 011 - 4000 4 Start_Stop_Count -O--CK 090 090 000 - 9119 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate POSR-- 252 252 051 - 0 8 Seek_Time_Performance P-S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 091 091 000 - 5292324 10 Spin_Retry_Count PO--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--C- 252 252 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 4692 184 End-to-End_Error -O--CK 252 252 000 - 0 187 Reported_Uncorrect -O--CK 252 252 000 - 0 188 Command_Timeout -O--CK 252 252 000 - 0 190 Airflow_Temperature_Cel -O---K 136 112 000 - 39 194 Temperature_Celsius -O---K 136 112 000 - 39 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--C- 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 199 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 252 252 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 75 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 75 [2] occurred at disk power-on lifetime: 43832 hours (1826 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 08 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 08 00 00 00 00 00 00 40 00 00:01:23.000 WRITE FPDMA QUEUED 60 00 80 00 80 00 00 00 00 00 00 40 00 00:01:23.000 READ FPDMA QUEUED 60 00 80 00 80 00 00 00 00 00 00 40 00 00:01:23.000 READ FPDMA QUEUED 61 00 04 00 04 00 00 00 00 00 00 40 00 00:01:23.000 WRITE FPDMA QUEUED 60 00 80 00 80 00 00 00 00 00 00 40 04 00:01:23.000 READ FPDMA QUEUED Error 74 [1] occurred at disk power-on lifetime: 43644 hours (1818 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 c2 4f 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 f8 00 00 00 00 00 c2 4f 00 e0 00 00:14:14.000 SMART [Vendor specific subcommand] 60 00 38 00 38 00 00 00 00 00 00 40 00 00:14:14.000 READ FPDMA QUEUED 60 01 00 01 00 00 00 00 00 00 00 40 00 00:14:14.000 READ FPDMA QUEUED 60 01 00 01 00 00 00 00 00 00 00 40 00 00:14:14.000 READ FPDMA QUEUED 60 00 e8 00 e8 00 00 00 00 00 00 40 00 00:14:14.000 READ FPDMA QUEUED Error 73 [0] occurred at disk power-on lifetime: 43644 hours (1818 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 f6 00 00 00 c2 4f b9 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 f8 00 f6 00 00 00 c2 4f b9 e0 00 00:14:13.000 SMART [Vendor specific subcommand] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:14:13.000 IDENTIFY DEVICE 61 00 08 00 08 00 00 00 c2 4f 00 40 00 00:14:13.000 WRITE FPDMA QUEUED b0 00 d8 00 00 00 00 00 c2 4f 00 a0 00 00:14:13.000 SMART ENABLE OPERATIONS 60 00 20 00 20 00 00 00 00 00 00 40 00 00:14:13.000 READ FPDMA QUEUED Error 72 [7] occurred at disk power-on lifetime: 41911 hours (1746 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 20 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 20 00 00 00 00 00 00 40 00 00:11:56.000 READ FPDMA QUEUED 61 01 00 01 00 00 00 00 00 00 00 40 04 00:11:56.000 WRITE FPDMA QUEUED 61 01 00 01 00 00 00 00 00 00 00 40 00 00:11:56.000 WRITE FPDMA QUEUED 61 01 00 01 00 00 00 00 00 00 00 40 00 00:11:56.000 WRITE FPDMA QUEUED 61 01 00 01 00 00 00 00 00 00 00 40 00 00:11:56.000 WRITE FPDMA QUEUED Error 71 [6] occurred at disk power-on lifetime: 43832 hours (1826 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 08 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 08 00 00 00 00 00 00 40 00 00:01:23.000 WRITE FPDMA QUEUED 60 00 80 00 80 00 00 00 00 00 00 40 00 00:01:23.000 READ FPDMA QUEUED 60 00 80 00 80 00 00 00 00 00 00 40 00 00:01:23.000 READ FPDMA QUEUED 61 00 04 00 04 00 00 00 00 00 00 40 00 00:01:23.000 WRITE FPDMA QUEUED 60 00 80 00 80 00 00 00 00 00 00 40 04 00:01:23.000 READ FPDMA QUEUED Error 70 [5] occurred at disk power-on lifetime: 43644 hours (1818 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 c2 4f 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 f8 00 00 00 00 00 c2 4f 00 e0 00 00:14:14.000 SMART [Vendor specific subcommand] 60 00 38 00 38 00 00 00 00 00 00 40 00 00:14:14.000 READ FPDMA QUEUED 60 01 00 01 00 00 00 00 00 00 00 40 00 00:14:14.000 READ FPDMA QUEUED 60 01 00 01 00 00 00 00 00 00 00 40 00 00:14:14.000 READ FPDMA QUEUED 60 00 e8 00 e8 00 00 00 00 00 00 40 00 00:14:14.000 READ FPDMA QUEUED Error 69 [4] occurred at disk power-on lifetime: 43644 hours (1818 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 f6 00 00 00 c2 4f b9 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 f8 00 f6 00 00 00 c2 4f b9 e0 00 00:14:13.000 SMART [Vendor specific subcommand] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:14:13.000 IDENTIFY DEVICE 61 00 08 00 08 00 00 00 c2 4f 00 40 00 00:14:13.000 WRITE FPDMA QUEUED b0 00 d8 00 00 00 00 00 c2 4f 00 a0 00 00:14:13.000 SMART ENABLE OPERATIONS 60 00 20 00 20 00 00 00 00 00 00 40 00 00:14:13.000 READ FPDMA QUEUED Error 68 [3] occurred at disk power-on lifetime: 41911 hours (1746 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 20 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 20 00 00 00 00 00 00 40 00 00:11:56.000 READ FPDMA QUEUED 61 01 00 01 00 00 00 00 00 00 00 40 04 00:11:56.000 WRITE FPDMA QUEUED 61 01 00 01 00 00 00 00 00 00 00 40 00 00:11:56.000 WRITE FPDMA QUEUED 61 01 00 01 00 00 00 00 00 00 00 40 00 00:11:56.000 WRITE FPDMA QUEUED 61 01 00 01 00 00 00 00 00 00 00 40 00 00:11:56.000 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 0 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: --/42 Celsius Lifetime Min/Max Temperature: --/48 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 10/105 Celsius Min/Max Temperature Limit: 5/110 Celsius Temperature History Size (Index): 128 (53) Index Estimated Time Temperature Celsius 54 2025-01-09 06:33 37 ****************** ... ..( 8 skipped). .. ****************** 63 2025-01-09 06:42 37 ****************** 64 2025-01-09 06:43 36 ***************** ... ..( 45 skipped). .. ***************** 110 2025-01-09 07:29 36 ***************** 111 2025-01-09 07:30 ? - 112 2025-01-09 07:31 23 **** 113 2025-01-09 07:32 24 ***** 114 2025-01-09 07:33 26 ******* 115 2025-01-09 07:34 30 *********** 116 2025-01-09 07:35 31 ************ 117 2025-01-09 07:36 31 ************ 118 2025-01-09 07:37 32 ************* 119 2025-01-09 07:38 33 ************** ... ..( 2 skipped). .. ************** 122 2025-01-09 07:41 33 ************** 123 2025-01-09 07:42 36 ***************** ... ..( 4 skipped). .. ***************** 0 2025-01-09 07:47 36 ***************** 1 2025-01-09 07:48 40 ********************* ... ..( 4 skipped). .. ********************* 6 2025-01-09 07:53 40 ********************* 7 2025-01-09 07:54 41 ********************** ... ..( 3 skipped). .. ********************** 11 2025-01-09 07:58 41 ********************** 12 2025-01-09 07:59 40 ********************* ... ..( 4 skipped). .. ********************* 17 2025-01-09 08:04 40 ********************* 18 2025-01-09 08:05 41 ********************** ... ..( 4 skipped). .. ********************** 23 2025-01-09 08:10 41 ********************** 24 2025-01-09 08:11 42 *********************** ... ..( 9 skipped). .. *********************** 34 2025-01-09 08:21 42 *********************** 35 2025-01-09 08:22 41 ********************** ... ..( 4 skipped). .. ********************** 40 2025-01-09 08:27 41 ********************** 41 2025-01-09 08:28 40 ********************* ... ..( 11 skipped). .. ********************* 53 2025-01-09 08:40 40 ********************* SMART WRITE LOG does not return COUNT and LBA_LOW register SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC