/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD5000BEVT-22A0RT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Dec 31 13:17:21 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13560) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 158) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 187 152 021 - 1641 4 Start_Stop_Count -O--CK 040 040 000 - 60015 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 075 075 000 - 18439 10 Spin_Retry_Count -O--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 091 091 000 - 9747 191 G-Sense_Error_Rate -O--CK 001 001 000 - 338 192 Power-Off_Retract_Count -O--CK 200 200 000 - 359 193 Load_Cycle_Count -O--CK 001 001 000 - 2849906 194 Temperature_Celsius -O---K 111 093 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 194 000 - 0 198 Offline_Uncorrectable ----CK 200 194 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 195 051 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 16915 hours (704 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1e 05 96 48 40 00 Error: WP at LBA = 0x1e059648 = 503682632 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 28 00 58 00 00 1d 13 18 18 40 08 05:49:03.649 WRITE FPDMA QUEUED 61 00 08 00 50 00 00 1e 09 96 d8 40 08 05:49:03.643 WRITE FPDMA QUEUED 61 00 08 00 38 00 00 1e 05 a7 e8 40 08 05:49:03.643 WRITE FPDMA QUEUED 60 00 08 00 30 00 00 1e 05 96 48 40 08 05:49:03.643 READ FPDMA QUEUED 61 00 08 00 28 00 00 31 0f 28 00 40 08 05:49:03.642 WRITE FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 16915 hours (704 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 10 00 00 1e 05 96 48 40 00 Error: UNC at LBA = 0x1e059648 = 503682632 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 90 00 00 1e 05 96 48 40 08 05:48:59.743 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 05:48:59.683 FLUSH CACHE EXT 61 00 08 00 80 00 00 1d 13 18 10 40 08 05:48:59.682 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 05:48:59.648 FLUSH CACHE EXT 61 00 90 00 30 00 00 1d 13 17 80 40 08 05:48:59.647 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 3915 - # 2 Short offline Completed without error 00% 24 - # 3 Short offline Completed without error 00% 24 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 37/37 Celsius Lifetime Min/Max Temperature: 26/56 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (71) Index Estimated Time Temperature Celsius 72 2023-12-31 11:10 34 *************** ... ..( 2 skipped). .. *************** 75 2023-12-31 11:13 34 *************** 76 2023-12-31 11:14 35 **************** ... ..( 35 skipped). .. **************** 112 2023-12-31 11:50 35 **************** 113 2023-12-31 11:51 34 *************** 114 2023-12-31 11:52 35 **************** 115 2023-12-31 11:53 35 **************** 116 2023-12-31 11:54 34 *************** ... ..( 5 skipped). .. *************** 122 2023-12-31 12:00 34 *************** 123 2023-12-31 12:01 35 **************** ... ..( 2 skipped). .. **************** 126 2023-12-31 12:04 35 **************** 127 2023-12-31 12:05 34 *************** 0 2023-12-31 12:06 35 **************** 1 2023-12-31 12:07 34 *************** 2 2023-12-31 12:08 35 **************** ... ..( 6 skipped). .. **************** 9 2023-12-31 12:15 35 **************** 10 2023-12-31 12:16 36 ***************** ... ..( 8 skipped). .. ***************** 19 2023-12-31 12:25 36 ***************** 20 2023-12-31 12:26 37 ****************** 21 2023-12-31 12:27 37 ****************** 22 2023-12-31 12:28 37 ****************** 23 2023-12-31 12:29 36 ***************** 24 2023-12-31 12:30 36 ***************** 25 2023-12-31 12:31 36 ***************** 26 2023-12-31 12:32 37 ****************** 27 2023-12-31 12:33 37 ****************** 28 2023-12-31 12:34 36 ***************** 29 2023-12-31 12:35 36 ***************** 30 2023-12-31 12:36 36 ***************** 31 2023-12-31 12:37 37 ****************** 32 2023-12-31 12:38 37 ****************** 33 2023-12-31 12:39 36 ***************** 34 2023-12-31 12:40 36 ***************** 35 2023-12-31 12:41 37 ****************** 36 2023-12-31 12:42 36 ***************** ... ..( 25 skipped). .. ***************** 62 2023-12-31 13:08 36 ***************** 63 2023-12-31 13:09 ? - 64 2023-12-31 13:10 36 ***************** 65 2023-12-31 13:11 ? - 66 2023-12-31 13:12 37 ****************** 67 2023-12-31 13:13 ? - 68 2023-12-31 13:14 37 ****************** 69 2023-12-31 13:15 ? - 70 2023-12-31 13:16 37 ****************** 71 2023-12-31 13:17 37 ****************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 161 Vendor specific