/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.5.6-300.fc39.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Marvell based SanDisk SSDs Device Model: SanDisk SSD PLUS 120GB Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: UE5000RL User Capacity: 120,040,980,480 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5528 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Apr 5 23:54:38 2024 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 32) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x15) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 21) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 20164 12 Power_Cycle_Count -O--CK 100 100 000 - 2910 165 Total_Write/Erase_Count -O--CK 100 100 000 - 17961 166 Min_W/E_Cycle -O--CK 100 100 --- - 165 167 Min_Bad_Block/Die -O--CK 100 100 --- - 0 168 Maximum_Erase_Cycle -O--CK 100 100 --- - 218 169 Total_Bad_Block -O--CK 100 100 --- - 105 170 Unknown_Marvell_Attr -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Avg_Write/Erase_Count -O--CK 100 100 000 - 165 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 126 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 3774 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 050 061 000 - 50 (Min/Max 18/61) 199 SATA_CRC_Error -O--CK 100 100 --- - 0 230 Perc_Write/Erase_Count -O--CK 100 100 000 - 13087 8448 13087 232 Perc_Avail_Resrvd_Space PO--CK 100 100 005 - 100 233 Total_NAND_Writes_GiB -O--CK 100 100 --- - 19829 234 Perc_Write/Erase_Ct_BC -O--CK 100 100 000 - 99915 241 Total_Writes_GiB ----CK 100 100 000 - 31650 242 Total_Reads_GiB ----CK 100 100 000 - 48032 244 Thermal_Throttle -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log 0xa7 GPL,SL VS 1 Device vendor specific log 0xa9 GPL,SL VS 3 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (16 sectors) Device Error Count: 3774 (device log contains only the most recent 64 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3774 [3] occurred at disk power-on lifetime: 20152 hours (839 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 00 01 e0 00 Error: UNC Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:09:50.771 READ LOG EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:09:50.749 FLUSH CACHE EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.702 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.568 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.513 READ LOG EXT Error 3773 [2] occurred at disk power-on lifetime: 20152 hours (839 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 05 00 00 00 00 00 05 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:09:50.749 FLUSH CACHE EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.702 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.568 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.513 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.492 READ LOG EXT Error 3772 [1] occurred at disk power-on lifetime: 20047 hours (835 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 8c 00 00 00 00 00 8c e0 00 Error: UNC Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:06.344 READ LOG EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:04:06.237 FLUSH CACHE EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.849 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.823 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.749 READ LOG EXT Error 3771 [0] occurred at disk power-on lifetime: 20047 hours (835 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 7c 00 00 00 00 00 7c a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:04:06.237 FLUSH CACHE EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.849 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.823 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.749 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:04:00.702 READ LOG EXT Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. Error 3770 [63] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 45 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 44 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 43 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 42 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 41 3d+07:32:11.153 NOP [Abort queued commands] Error 3769 [62] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 35 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 34 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 33 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 32 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 31 3d+07:32:11.153 NOP [Abort queued commands] Error 3768 [61] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 25 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 24 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 23 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 22 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 21 3d+07:32:11.153 NOP [Abort queued commands] Error 3767 [60] occurred at disk power-on lifetime: 43981 hours (1832 days + 13 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 15 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 14 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 13 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 12 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 11 3d+07:32:11.153 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 2910 --- Lifetime Power-On Resets 0x01 0x010 4 20164 --- Power-on Hours 0x01 0x018 6 66376462748 --- Logical Sectors Written 0x01 0x028 6 100730835090 --- Logical Sectors Read 0x01 0x038 6 20164 --- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 50 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 60 --- Highest Temperature 0x05 0x028 1 33 --- Lowest Temperature 0x05 0x030 1 50 --- Highest Average Short Term Temperature 0x05 0x038 1 50 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 33 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error /dev/sdb smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.5.6-300.fc39.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z5K500 Device Model: HGST HTS545050A7E380 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GG2OAC90 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Apr 5 23:54:38 2024 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 115) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 100 100 040 - 0 3 Spin_Up_Time POS--- 214 214 033 - 1 4 Start_Stop_Count -O--C- 097 097 000 - 5580 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 0 9 Power_On_Hours -O--C- 019 019 000 - 35878 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 4810 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 099 099 000 - 257 193 Load_Cycle_Count -O--C- 001 001 000 - 1287325 194 Temperature_Celsius -O---- 153 153 000 - 39 (Min/Max 19/55) 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 37736 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 37736 [3] occurred at disk power-on lifetime: 14310 hours (596 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 4e bf 88 00 00 Error: WP at LBA = 0x004ebf88 = 5160840 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 40 00 c8 00 00 00 83 07 20 40 00 09:49:08.716 WRITE FPDMA QUEUED 60 00 70 00 c0 00 00 00 4e c4 88 40 00 09:49:08.542 READ FPDMA QUEUED 60 01 00 00 b8 00 00 00 4e c3 88 40 00 09:49:08.542 READ FPDMA QUEUED 60 01 00 00 b0 00 00 00 4e c2 88 40 00 09:49:08.542 READ FPDMA QUEUED 60 01 00 00 a8 00 00 00 4e c1 88 40 00 09:49:08.542 READ FPDMA QUEUED Error 37735 [2] occurred at disk power-on lifetime: 14310 hours (596 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 18 00 00 00 4e bf 88 00 00 Error: UNC at LBA = 0x004ebf88 = 5160840 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 18 00 10 00 00 00 4e bf 88 40 00 09:49:04.925 READ FPDMA QUEUED 61 00 20 00 08 00 00 27 ea 8e 00 40 00 09:49:04.893 WRITE FPDMA QUEUED 61 00 20 00 f8 00 00 00 1a a8 e0 40 00 09:49:04.893 WRITE FPDMA QUEUED 60 00 20 00 f0 00 00 00 1b 9e 20 40 00 09:49:04.893 READ FPDMA QUEUED 61 00 20 00 e8 00 00 27 ea 8e 00 40 00 09:49:04.892 WRITE FPDMA QUEUED Error 37734 [1] occurred at disk power-on lifetime: 14310 hours (596 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 4e bf 88 00 00 Error: WP at LBA = 0x004ebf88 = 5160840 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 a0 00 00 00 67 d9 f0 40 00 09:48:41.093 WRITE FPDMA QUEUED 60 00 70 00 98 00 00 00 4e c4 88 40 00 09:48:41.093 READ FPDMA QUEUED 60 01 00 00 90 00 00 00 4e c3 88 40 00 09:48:41.093 READ FPDMA QUEUED 60 01 00 00 88 00 00 00 4e c2 88 40 00 09:48:41.093 READ FPDMA QUEUED 60 01 00 00 80 00 00 00 4e c1 88 40 00 09:48:41.093 READ FPDMA QUEUED Error 37733 [0] occurred at disk power-on lifetime: 14310 hours (596 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 18 00 00 00 4e bf 88 00 00 Error: UNC at LBA = 0x004ebf88 = 5160840 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 18 00 58 00 00 00 4e bf 88 40 00 09:48:37.616 READ FPDMA QUEUED 61 00 58 00 50 00 00 00 0b e8 80 40 00 09:48:37.153 WRITE FPDMA QUEUED 60 00 58 00 48 00 00 00 0c 71 d8 40 00 09:48:37.131 READ FPDMA QUEUED 61 00 10 00 40 00 00 00 0c a6 20 40 00 09:48:37.025 WRITE FPDMA QUEUED 60 00 10 00 38 00 00 00 0d 30 a0 40 00 09:48:37.025 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 38/39 Celsius Lifetime Min/Max Temperature: 19/55 Celsius Specified Max Operating Temperature: 36 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (62) Index Estimated Time Temperature Celsius 63 2024-04-05 21:47 38 ******************* 64 2024-04-05 21:48 38 ******************* 65 2024-04-05 21:49 37 ****************** 66 2024-04-05 21:50 38 ******************* ... ..( 40 skipped). .. ******************* 107 2024-04-05 22:31 38 ******************* 108 2024-04-05 22:32 37 ****************** ... ..( 2 skipped). .. ****************** 111 2024-04-05 22:35 37 ****************** 112 2024-04-05 22:36 38 ******************* ... ..( 48 skipped). .. ******************* 33 2024-04-05 23:25 38 ******************* 34 2024-04-05 23:26 39 ******************** 35 2024-04-05 23:27 ? - 36 2024-04-05 23:28 39 ******************** ... ..( 8 skipped). .. ******************** 45 2024-04-05 23:37 39 ******************** 46 2024-04-05 23:38 ? - 47 2024-04-05 23:39 39 ******************** ... ..( 5 skipped). .. ******************** 53 2024-04-05 23:45 39 ******************** 54 2024-04-05 23:46 38 ******************* ... ..( 3 skipped). .. ******************* 58 2024-04-05 23:50 38 ******************* 59 2024-04-05 23:51 39 ******************** ... ..( 2 skipped). .. ******************** 62 2024-04-05 23:54 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdc smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.5.6-300.fc39.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron Client SSDs Device Model: CT480BX500SSD1 Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: M6CR022 User Capacity: 480,103,981,056 bytes [480 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Apr 5 23:54:39 2024 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 000 100 000 - 0 5 Reallocate_NAND_Blk_Cnt -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 1986 12 Power_Cycle_Count -O--CK 100 100 000 - 600 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 000 000 000 - 0 173 Ave_Block-Erase_Count -O--CK 000 000 000 - 10 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 100 180 Unused_Reserve_NAND_Blk PO--CK 100 100 000 - 220 183 SATA_Interfac_Downshift -O--CK 100 100 000 - 0 184 Error_Correction_Count -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 055 024 000 - 45 (Min/Max 17/76) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_ECC_Cnt -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 202 Percent_Lifetime_Remain ----CK 100 100 001 - 0 206 Write_Error_Rate -OSR-- 000 000 000 - 0 210 Success_RAIN_Recov_Cnt -O--CK 100 100 000 - 0 246 Total_LBAs_Written -O--CK 100 100 000 - 3258543507 247 Host_Program_Page_Count -O--CK 100 100 000 - 101829484 248 FTL_Program_Page_Count -O--CK 100 100 000 - 69838848 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 32 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 600 --- Lifetime Power-On Resets 0x01 0x010 4 1986 --- Power-on Hours 0x01 0x018 6 3258543507 --- Logical Sectors Written 0x01 0x020 6 14569383 --- Number of Write Commands 0x01 0x028 6 1511045457 --- Logical Sectors Read 0x01 0x030 6 49771066 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET