/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device Model: ST3500320AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: SD15 User Capacity: 500 106 780 160 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Mar 9 13:59:59 2016 YEKT ==> WARNING: There are known problems with these drives, THIS DRIVE MAY OR MAY NOT BE AFFECTED, see the following web pages for details: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/207951en http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=632758 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 650) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 116) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 112 080 006 - 214056810 3 Spin_Up_Time PO---- 097 094 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 299 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 541 7 Seek_Error_Rate POSR-- 078 060 030 - 39225408348 9 Power_On_Hours -O--CK 045 045 000 - 48241 10 Spin_Retry_Count PO--C- 100 100 097 - 3 12 Power_Cycle_Count -O--CK 100 100 020 - 308 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 18273 188 Command_Timeout -O--CK 100 098 000 - 8590065807 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 069 058 045 - 31 (Min/Max 30/31) 194 Temperature_Celsius -O---K 031 042 000 - 31 (0 17 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 035 008 000 - 214056810 197 Current_Pending_Sector -O--C- 100 100 000 - 1 198 Offline_Uncorrectable ----C- 100 100 000 - 1 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2819 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 18653 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 18653 [12] occurred at disk power-on lifetime: 47939 hours (1997 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 0b fa 00 71 7c 00 00 Error: UNC at LBA = 0xbfa00717c = 51438973308 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 02 20 00 0b f8 00 71 5f 40 00 1d+06:30:15.264 READ FPDMA QUEUED 61 00 00 02 10 00 0d f9 00 03 af 40 00 1d+06:30:15.257 WRITE FPDMA QUEUED 60 00 00 02 10 00 04 99 00 60 07 40 00 1d+06:30:15.246 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 00 00 3f 40 00 1d+06:30:15.232 READ FPDMA QUEUED 61 00 00 00 08 00 09 52 00 50 a7 40 00 1d+06:30:14.889 WRITE FPDMA QUEUED Error 18652 [11] occurred at disk power-on lifetime: 47938 hours (1997 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 06 02 00 2f 5d 00 00 Error: UNC at LBA = 0x602002f5d = 25803370333 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:21.358 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 1d+06:08:21.288 READ LOG EXT 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:15.869 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 1d+06:08:15.808 READ LOG EXT 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:10.688 READ FPDMA QUEUED Error 18651 [10] occurred at disk power-on lifetime: 47938 hours (1997 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 06 02 00 2f 5d 00 00 Error: UNC at LBA = 0x602002f5d = 25803370333 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:15.869 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 1d+06:08:15.808 READ LOG EXT 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:10.688 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 1d+06:08:10.619 READ LOG EXT 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:05.108 READ FPDMA QUEUED Error 18650 [9] occurred at disk power-on lifetime: 47938 hours (1997 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 06 02 00 2f 5d 00 00 Error: UNC at LBA = 0x602002f5d = 25803370333 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:10.688 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 1d+06:08:10.619 READ LOG EXT 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:05.108 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 1d+06:08:05.030 READ LOG EXT 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:00.274 READ FPDMA QUEUED Error 18649 [8] occurred at disk power-on lifetime: 47938 hours (1997 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 06 02 00 2f 5d 00 00 Error: UNC at LBA = 0x602002f5d = 25803370333 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:05.108 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 1d+06:08:05.030 READ LOG EXT 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:00.274 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 1d+06:08:00.083 READ LOG EXT 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:07:54.710 READ FPDMA QUEUED Error 18648 [7] occurred at disk power-on lifetime: 47938 hours (1997 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 06 02 00 2f 5d 00 00 Error: UNC at LBA = 0x602002f5d = 25803370333 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:08:00.274 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 1d+06:08:00.083 READ LOG EXT 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:07:54.710 READ FPDMA QUEUED 61 00 00 00 01 00 00 34 00 23 d7 40 00 1d+06:07:54.674 WRITE FPDMA QUEUED 60 00 00 00 38 00 04 87 00 43 47 40 00 1d+06:07:54.673 READ FPDMA QUEUED Error 18647 [6] occurred at disk power-on lifetime: 47938 hours (1997 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 06 02 00 2f 5d 00 00 Error: UNC at LBA = 0x602002f5d = 25803370333 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 06 fe 00 2e 7f 40 00 1d+06:07:54.710 READ FPDMA QUEUED 61 00 00 00 01 00 00 34 00 23 d7 40 00 1d+06:07:54.674 WRITE FPDMA QUEUED 60 00 00 00 38 00 04 87 00 43 47 40 00 1d+06:07:54.673 READ FPDMA QUEUED 61 00 00 00 08 00 06 56 00 6c c7 40 00 1d+06:07:54.673 WRITE FPDMA QUEUED 61 00 00 00 08 00 02 7b 00 95 17 40 00 1d+06:07:54.673 WRITE FPDMA QUEUED Error 18646 [5] occurred at disk power-on lifetime: 47938 hours (1997 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 06 02 00 2f 5d 00 00 Error: UNC at LBA = 0x602002f5d = 25803370333 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 38 00 04 87 00 43 47 40 00 1d+06:07:48.713 READ FPDMA QUEUED 61 00 00 00 08 00 06 56 00 6c c7 40 00 1d+06:07:48.712 WRITE FPDMA QUEUED 61 00 00 00 08 00 02 7b 00 95 17 40 00 1d+06:07:48.712 WRITE FPDMA QUEUED 61 00 00 00 08 00 06 79 00 39 9f 40 00 1d+06:07:48.711 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 e6 00 5f 4f 40 00 1d+06:07:48.711 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 30/31 Celsius Lifetime Min/Max Temperature: 17/42 Celsius Under/Over Temperature Limit Count: 0/25 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (110) Index Estimated Time Temperature Celsius 111 2016-03-09 11:52 31 ************ ... ..( 13 skipped). .. ************ 125 2016-03-09 12:06 31 ************ 126 2016-03-09 12:07 ? - 127 2016-03-09 12:08 31 ************ ... ..( 36 skipped). .. ************ 36 2016-03-09 12:45 31 ************ 37 2016-03-09 12:46 30 *********** ... ..( 8 skipped). .. *********** 46 2016-03-09 12:55 30 *********** 47 2016-03-09 12:56 ? - 48 2016-03-09 12:57 30 *********** ... ..( 2 skipped). .. *********** 51 2016-03-09 13:00 30 *********** 52 2016-03-09 13:01 31 ************ ... ..( 10 skipped). .. ************ 63 2016-03-09 13:12 31 ************ 64 2016-03-09 13:13 30 *********** ... ..( 2 skipped). .. *********** 67 2016-03-09 13:16 30 *********** 68 2016-03-09 13:17 ? - 69 2016-03-09 13:18 30 *********** ... ..( 7 skipped). .. *********** 77 2016-03-09 13:26 30 *********** 78 2016-03-09 13:27 ? - 79 2016-03-09 13:28 30 *********** ... ..( 4 skipped). .. *********** 84 2016-03-09 13:33 30 *********** 85 2016-03-09 13:34 ? - 86 2016-03-09 13:35 30 *********** ... ..( 19 skipped). .. *********** 106 2016-03-09 13:55 30 *********** 107 2016-03-09 13:56 31 ************ 108 2016-03-09 13:57 31 ************ 109 2016-03-09 13:58 30 *********** 110 2016-03-09 13:59 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS