/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.0-6-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Constellation CS Device Model: ST1000NC000-1CX162 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CNS1 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat May 7 05:56:38 2022 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 575) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 110) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x10bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 078 063 044 - 79118360 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 76 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 084 060 030 - 265232637 9 Power_On_Hours -O--CK 023 023 000 - 68189 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 76 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 099 099 000 - 1 190 Airflow_Temperature_Cel -O---K 065 044 045 Past 35 (Min/Max 33/41 #76) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 28 193 Load_Cycle_Count -O--CK 100 100 000 - 76 194 Temperature_Celsius -O---K 035 056 000 - 35 (0 21 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL,SL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbd GPL VS 512 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 48951 - # 2 Short offline Completed without error 00% 38649 - # 3 Short offline Completed without error 00% 38481 - # 4 Short offline Completed without error 00% 38313 - # 5 Short offline Completed without error 00% 38145 - # 6 Short offline Completed without error 00% 37977 - # 7 Short offline Completed without error 00% 37809 - # 8 Short offline Completed without error 00% 37641 - # 9 Short offline Completed without error 00% 37473 - #10 Short offline Completed without error 00% 37305 - #11 Short offline Completed without error 00% 37137 - #12 Short offline Completed without error 00% 36969 - #13 Short offline Completed without error 00% 36801 - #14 Short offline Completed without error 00% 36633 - #15 Short offline Completed without error 00% 36465 - #16 Short offline Completed without error 00% 36297 - #17 Short offline Completed without error 00% 36129 - #18 Short offline Completed without error 00% 35961 - #19 Short offline Completed without error 00% 35793 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 32/41 Celsius Lifetime Min/Max Temperature: 21/56 Celsius Under/Over Temperature Limit Count: 0/3988 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (127) Index Estimated Time Temperature Celsius 0 2022-05-06 08:40 34 *************** ... ..( 5 skipped). .. *************** 6 2022-05-06 09:40 34 *************** 7 2022-05-06 09:50 35 **************** 8 2022-05-06 10:00 35 **************** 9 2022-05-06 10:10 36 ***************** 10 2022-05-06 10:20 37 ****************** 11 2022-05-06 10:30 38 ******************* ... ..( 4 skipped). .. ******************* 16 2022-05-06 11:20 38 ******************* 17 2022-05-06 11:30 39 ******************** ... ..( 5 skipped). .. ******************** 23 2022-05-06 12:30 39 ******************** 24 2022-05-06 12:40 38 ******************* 25 2022-05-06 12:50 37 ****************** ... ..( 11 skipped). .. ****************** 37 2022-05-06 14:50 37 ****************** 38 2022-05-06 15:00 38 ******************* ... ..( 26 skipped). .. ******************* 65 2022-05-06 19:30 38 ******************* 66 2022-05-06 19:40 37 ****************** ... ..( 19 skipped). .. ****************** 86 2022-05-06 23:00 37 ****************** 87 2022-05-06 23:10 36 ***************** ... ..( 15 skipped). .. ***************** 103 2022-05-07 01:50 36 ***************** 104 2022-05-07 02:00 35 **************** ... ..( 22 skipped). .. **************** 127 2022-05-07 05:50 35 **************** SCT Error Recovery Control: Read: 100 (10.0 seconds) Write: 100 (10.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.0-6-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Constellation CS Device Model: ST1000NC000-1CX162 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CE02 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat May 7 05:56:38 2022 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 113) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x10bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 078 063 044 - 68586400 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 126 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 888 7 Seek_Error_Rate POSR-- 087 060 030 - 657842512 9 Power_On_Hours -O--CK 018 018 000 - 72665 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 126 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 097 097 000 - 3 188 Command_Timeout -O--CK 100 001 000 - 13087 189 High_Fly_Writes -O-RCK 098 098 000 - 2 190 Airflow_Temperature_Cel -O---K 064 044 045 Past 36 (Min/Max 34/43 #32) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 67 193 Load_Cycle_Count -O--CK 100 100 000 - 126 194 Temperature_Celsius -O---K 036 056 000 - 36 (0 21 0 0 0) 197 Current_Pending_Sector -O--C- 100 097 000 - 0 198 Offline_Uncorrectable ----C- 100 097 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 16 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL,SL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 6 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [5] occurred at disk power-on lifetime: 27208 hours (1133 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1c df 66 38 00 00 Error: UNC at LBA = 0x1cdf6638 = 484402744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1c df 66 38 e0 00 7d+12:14:58.281 READ DMA EXT 25 00 00 00 08 00 00 1c df 66 30 e0 00 7d+12:14:58.251 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 7d+12:14:58.211 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 7d+12:14:58.209 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 7d+12:14:58.209 SET FEATURES [Set transfer mode] Error 5 [4] occurred at disk power-on lifetime: 27208 hours (1133 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1c df 66 38 00 00 Error: UNC at LBA = 0x1cdf6638 = 484402744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1c df 66 38 e0 00 7d+12:14:58.281 READ DMA EXT 25 00 00 00 08 00 00 1c df 66 30 e0 00 7d+12:14:58.251 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 7d+12:14:58.211 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 7d+12:14:58.209 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 7d+12:14:58.209 SET FEATURES [Set transfer mode] Error 4 [3] occurred at disk power-on lifetime: 27208 hours (1133 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1c df 66 38 00 00 Error: UNC at LBA = 0x1cdf6638 = 484402744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 1c df 66 30 e0 00 7d+12:14:55.290 READ DMA EXT 25 00 00 00 10 00 00 1c de 91 50 e0 00 7d+12:14:55.280 READ DMA EXT 25 00 00 00 10 00 00 1c de 53 90 e0 00 7d+12:14:55.271 READ DMA EXT 25 00 00 00 10 00 00 1c de 2b 90 e0 00 7d+12:14:55.263 READ DMA EXT 25 00 00 00 10 00 00 1d 3e 26 40 e0 00 7d+12:14:55.262 READ DMA EXT Error 3 [2] occurred at disk power-on lifetime: 27208 hours (1133 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1c df 66 38 00 00 Error: UNC at LBA = 0x1cdf6638 = 484402744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 1c df 66 30 e0 00 7d+12:14:55.290 READ DMA EXT 25 00 00 00 10 00 00 1c de 91 50 e0 00 7d+12:14:55.280 READ DMA EXT 25 00 00 00 10 00 00 1c de 53 90 e0 00 7d+12:14:55.271 READ DMA EXT 25 00 00 00 10 00 00 1c de 2b 90 e0 00 7d+12:14:55.263 READ DMA EXT 25 00 00 00 10 00 00 1d 3e 26 40 e0 00 7d+12:14:55.262 READ DMA EXT Error 2 [1] occurred at disk power-on lifetime: 27193 hours (1133 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 63 9d 65 b0 00 00 Error: UNC at LBA = 0x639d65b0 = 1671259568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 d0 00 00 63 9d 65 30 e0 00 6d+21:28:19.812 READ DMA EXT 25 00 00 00 d0 00 00 63 d1 49 48 e0 00 6d+21:28:19.498 READ DMA EXT 25 00 00 00 d0 00 00 63 bf f1 d8 e0 00 6d+21:28:19.080 READ DMA EXT 25 00 00 00 d0 00 00 63 a3 a5 e0 e0 00 6d+21:28:19.061 READ DMA EXT 25 00 00 00 b0 00 00 63 bd bf 38 e0 00 6d+21:28:18.547 READ DMA EXT Error 1 [0] occurred at disk power-on lifetime: 27193 hours (1133 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 63 9d 65 b0 00 00 Error: UNC at LBA = 0x639d65b0 = 1671259568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 d0 00 00 63 9d 65 30 e0 00 6d+21:28:19.812 READ DMA EXT 25 00 00 00 d0 00 00 63 d1 49 48 e0 00 6d+21:28:19.498 READ DMA EXT 25 00 00 00 d0 00 00 63 bf f1 d8 e0 00 6d+21:28:19.080 READ DMA EXT 25 00 00 00 d0 00 00 63 a3 a5 e0 e0 00 6d+21:28:19.061 READ DMA EXT 25 00 00 00 b0 00 00 63 bd bf 38 e0 00 6d+21:28:18.547 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 53358 - # 2 Extended offline Completed without error 00% 19504 - # 3 Short offline Completed without error 00% 19502 - # 4 Short offline Completed without error 00% 17039 - # 5 Short offline Interrupted (host reset) 60% 17039 - # 6 Short offline Completed without error 00% 7 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 34/43 Celsius Lifetime Min/Max Temperature: 21/56 Celsius Under/Over Temperature Limit Count: 0/3983 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (62) Index Estimated Time Temperature Celsius 63 2022-05-06 08:40 35 **************** ... ..( 4 skipped). .. **************** 68 2022-05-06 09:30 35 **************** 69 2022-05-06 09:40 36 ***************** ... ..( 5 skipped). .. ***************** 75 2022-05-06 10:40 36 ***************** 76 2022-05-06 10:50 37 ****************** 77 2022-05-06 11:00 39 ******************** 78 2022-05-06 11:10 39 ******************** 79 2022-05-06 11:20 39 ******************** 80 2022-05-06 11:30 40 ********************* ... ..( 10 skipped). .. ********************* 91 2022-05-06 13:20 40 ********************* 92 2022-05-06 13:30 39 ******************** 93 2022-05-06 13:40 39 ******************** 94 2022-05-06 13:50 38 ******************* ... ..( 2 skipped). .. ******************* 97 2022-05-06 14:20 38 ******************* 98 2022-05-06 14:30 39 ******************** ... ..( 32 skipped). .. ******************** 3 2022-05-06 20:00 39 ******************** 4 2022-05-06 20:10 38 ******************* ... ..( 17 skipped). .. ******************* 22 2022-05-06 23:10 38 ******************* 23 2022-05-06 23:20 37 ****************** ... ..( 16 skipped). .. ****************** 40 2022-05-07 02:10 37 ****************** 41 2022-05-07 02:20 36 ***************** ... ..( 20 skipped). .. ***************** 62 2022-05-07 05:50 36 ***************** SCT Error Recovery Control: Read: 100 (10.0 seconds) Write: 100 (10.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.0-6-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.9 Device Model: ST3160812AS Serial Number: -- Firmware Version: 3.AAH User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sat May 7 05:56:38 2022 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 54) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 097 072 006 - 160787408 3 Spin_Up_Time PO---- 094 094 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 292 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 1 7 Seek_Error_Rate POSR-- 087 052 030 - 537192563 9 Power_On_Hours -O--CK 001 001 000 - 88861 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 318 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 061 038 045 Past 39 (Min/Max 37/44 #29785) 194 Temperature_Celsius -O---K 039 062 000 - 39 (0 21 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 047 045 000 - 54974770 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 6528 - # 2 Extended offline Completed without error 00% 42450 - # 3 Short offline Completed without error 00% 42449 - # 4 Extended offline Completed without error 00% 4819 - # 5 Short offline Completed without error 00% 4818 - # 6 Short captive Interrupted (host reset) 70% 4818 - # 7 Short offline Completed without error 00% 4818 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdd smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.0-6-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 850 EVO 250GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EMT02B6Q User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat May 7 05:56:39 2022 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 133) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 096 096 000 - 17980 12 Power_Cycle_Count -O--CK 099 099 000 - 78 177 Wear_Leveling_Count PO--C- 098 098 000 - 22 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 068 057 000 - 32 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 32 241 Total_LBAs_Written -O--CK 099 099 000 - 12979999637 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 30/38 Celsius Lifetime Min/Max Temperature: 16/43 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (44) Index Estimated Time Temperature Celsius 45 2022-05-06 08:40 31 ************ ... ..( 2 skipped). .. ************ 48 2022-05-06 09:10 31 ************ 49 2022-05-06 09:20 32 ************* ... ..( 4 skipped). .. ************* 54 2022-05-06 10:10 32 ************* 55 2022-05-06 10:20 33 ************** ... ..( 6 skipped). .. ************** 62 2022-05-06 11:30 33 ************** 63 2022-05-06 11:40 34 *************** ... ..( 7 skipped). .. *************** 71 2022-05-06 13:00 34 *************** 72 2022-05-06 13:10 35 **************** ... ..( 14 skipped). .. **************** 87 2022-05-06 15:40 35 **************** 88 2022-05-06 15:50 36 ***************** ... ..( 13 skipped). .. ***************** 102 2022-05-06 18:10 36 ***************** 103 2022-05-06 18:20 35 **************** ... ..( 15 skipped). .. **************** 119 2022-05-06 21:00 35 **************** 120 2022-05-06 21:10 34 *************** ... ..( 15 skipped). .. *************** 8 2022-05-06 23:50 34 *************** 9 2022-05-07 00:00 33 ************** ... ..( 19 skipped). .. ************** 29 2022-05-07 03:20 33 ************** 30 2022-05-07 03:30 32 ************* ... ..( 13 skipped). .. ************* 44 2022-05-07 05:50 32 ************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sde smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.0-6-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F2 EG Device Model: SAMSUNG HD103SI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AG01113 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Sat May 7 05:56:39 2022 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13098) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 219) minutes. Conveyance self-test routine recommended polling time: ( 23) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 074 074 011 - 8600 4 Start_Stop_Count -O--CK 055 055 000 - 45234 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 100 100 051 - 0 8 Seek_Time_Performance P-S--K 100 100 015 - 13607 9 Power_On_Hours -O--CK 082 082 000 - 90922 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 091 091 000 - 6763 12 Power_Cycle_Count -O--CK 100 100 000 - 397 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 0 183 Runtime_Bad_Block -O--CK 100 100 000 - 20 184 End-to-End_Error PO--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 074 054 000 - 26 (Min/Max 20/33) 194 Temperature_Celsius -O---K 078 050 000 - 22 (Min/Max 20/36) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 2808752250 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 099 000 - 10 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL R/O 2 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 2 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 10 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 [1] occurred at disk power-on lifetime: 14956 hours (623 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 53 00 99 00 00 45 4e c0 6e e0 00 Error: ICRC, ABRT 153 sectors at LBA = 0x454ec06e = 1162788974 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 45 4e c0 07 e0 00 40d+06:38:47.410 READ DMA EXT 25 00 00 01 00 00 00 45 4e bf 07 e0 00 40d+06:38:35.350 READ DMA EXT 25 00 00 01 00 00 00 45 4e be 07 e0 00 40d+06:38:35.350 READ DMA EXT 25 00 00 01 00 00 00 45 4e bd 07 e0 00 40d+06:38:35.350 READ DMA EXT 25 00 00 01 00 00 00 45 4e bc 07 e0 00 40d+06:38:35.350 READ DMA EXT Error 9 [0] occurred at disk power-on lifetime: 14953 hours (623 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 80 00 01 00 00 00 00 00 01 a0 00 at LBA = 0x00000001 = 1 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 da 04 00 00 00 00 ee d1 5f 40 00 40d+02:48:32.510 WRITE FPDMA QUEUED 61 00 d0 04 00 00 00 00 ee cd 5f 40 00 40d+02:48:29.280 WRITE FPDMA QUEUED 61 00 00 02 10 00 00 00 ee cb 47 40 00 40d+02:48:29.170 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 ee c7 47 40 00 40d+02:48:29.040 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 ee c3 47 40 00 40d+02:48:28.920 WRITE FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 14953 hours (623 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 80 00 01 00 00 00 00 00 01 a0 00 at LBA = 0x00000001 = 1 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 b8 00 00 00 34 6f 9f 40 00 40d+02:46:35.810 WRITE FPDMA QUEUED 61 00 d1 04 00 00 00 00 ec 8c 1f 40 00 40d+02:46:35.810 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 ec 88 1f 40 00 40d+02:46:35.800 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 ec 84 1f 40 00 40d+02:46:35.800 WRITE FPDMA QUEUED 61 00 00 03 98 00 00 00 ec 80 7f 40 00 40d+02:46:35.800 WRITE FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 14953 hours (623 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 80 00 01 00 00 00 00 00 01 a0 00 at LBA = 0x00000001 = 1 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 04 00 00 00 00 eb 9f 67 40 00 40d+02:45:20.210 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 eb 9b 67 40 00 40d+02:45:20.200 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 eb 97 67 40 00 40d+02:45:16.820 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 eb 93 67 40 00 40d+02:45:16.690 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 eb 8f 5f 40 00 40d+02:45:16.690 WRITE FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 14952 hours (623 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 48 03 00 00 00 44 ea 23 87 40 00 at LBA = 0x44ea2387 = 1156195207 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 03 80 00 00 00 ea 3a 8f 40 00 40d+02:43:17.080 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 ea 36 8f 40 00 40d+02:43:16.960 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 ea 32 8f 40 00 40d+02:43:13.710 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 ea 2e 87 40 00 40d+02:43:13.590 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 ea 2a 87 40 00 40d+02:43:08.880 WRITE FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 14929 hours (622 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 80 00 01 00 00 00 00 00 01 a0 00 at LBA = 0x00000001 = 1 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 00 51 75 f7 40 00 39d+03:29:14.970 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 51 74 f7 40 00 39d+03:29:14.970 READ FPDMA QUEUED 60 00 00 02 00 00 00 00 51 72 f7 40 00 39d+03:29:08.570 READ FPDMA QUEUED 61 00 00 04 00 00 00 00 2d 2a 37 40 00 39d+03:29:02.880 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 2d 26 37 40 00 39d+03:29:02.880 WRITE FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 14834 hours (618 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 48 03 00 00 00 48 05 d7 07 40 00 at LBA = 0x4805d707 = 1208342279 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 04 00 00 00 00 05 f2 0f 40 00 35d+04:10:42.640 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 05 ee 0f 40 00 35d+04:10:42.640 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 05 ea 0f 40 00 35d+04:10:42.640 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 05 e6 0f 40 00 35d+04:10:42.640 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 05 e2 0f 40 00 35d+04:10:42.640 WRITE FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 14834 hours (618 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 80 00 01 00 00 00 00 00 01 a0 00 at LBA = 0x00000001 = 1 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 04 00 00 00 00 05 74 8f 40 00 35d+04:09:37.590 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 05 70 8f 40 00 35d+04:09:37.590 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 05 6c 8f 40 00 35d+04:09:37.590 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 05 68 8f 40 00 35d+04:09:37.590 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 00 05 64 8f 40 00 35d+04:09:37.590 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 52647 - # 2 Extended offline Aborted by host 80% 37705 - # 3 Short offline Completed without error 00% 37705 - # 4 Short offline Completed without error 00% 24491 - # 5 Short offline Completed without error 00% 14960 - # 6 Short offline Interrupted (host reset) 90% 14957 - # 7 Short offline Interrupted (host reset) 90% 14957 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: --/36 Celsius Lifetime Min/Max Temperature: --/50 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (18) Index Estimated Time Temperature Celsius 19 2022-05-07 03:49 27 ******** ... ..( 9 skipped). .. ******** 29 2022-05-07 03:59 27 ******** 30 2022-05-07 04:00 25 ****** 31 2022-05-07 04:01 25 ****** 32 2022-05-07 04:02 25 ****** 33 2022-05-07 04:03 24 ***** ... ..( 18 skipped). .. ***** 52 2022-05-07 04:22 24 ***** 53 2022-05-07 04:23 25 ****** ... ..( 5 skipped). .. ****** 59 2022-05-07 04:29 25 ****** 60 2022-05-07 04:30 26 ******* ... ..( 9 skipped). .. ******* 70 2022-05-07 04:40 26 ******* 71 2022-05-07 04:41 27 ******** ... ..( 30 skipped). .. ******** 102 2022-05-07 05:12 27 ******** 103 2022-05-07 05:13 28 ********* 104 2022-05-07 05:14 28 ********* 105 2022-05-07 05:15 28 ********* 106 2022-05-07 05:16 27 ******** 107 2022-05-07 05:17 28 ********* ... ..( 12 skipped). .. ********* 120 2022-05-07 05:30 28 ********* 121 2022-05-07 05:31 22 *** ... ..( 24 skipped). .. *** 18 2022-05-07 05:56 22 *** SCT Error Recovery Control: Read: Disabled Write: Disabled ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: scsi error aborted command Read Device Statistics page 0x00 failed Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 8 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC