/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-29-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST750LM022 HN-M750MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2BA30001 User Capacity: 750,156,374,016 bytes [750 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 10 06:06:46 2020 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 254 APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10560) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 176) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 2 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 093 088 025 - 2407 4 Start_Stop_Count -O--CK 096 096 000 - 4163 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 14578 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 7 12 Power_Cycle_Count -O--CK 096 096 000 - 4136 13 Read_Soft_Error_Rate -O-RCK 100 100 000 - 0 181 Program_Fail_Cnt_Total -O---K 099 099 000 - 26767142 191 G-Sense_Error_Rate -O---K 100 100 000 - 393 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 193 Load_Cycle_Count -O--CK 075 075 000 - 258721 194 Temperature_Celsius -O---- 064 054 000 - 28 (Min/Max 13/46) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 332 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 16020 240 Head_Flying_Hours -O--CK 100 100 000 - 14530 241 Total_LBAs_Written -O--CK 094 094 000 - 8196306 242 Total_LBAs_Read -O--CK 092 092 000 - 11890192 254 Free_Fall_Sensor -O--CK 252 252 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 333 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 333 [4] occurred at disk power-on lifetime: 14232 hours (593 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 18 00 00 05 e9 04 40 40 00 Error: ICRC, ABRT at LBA = 0x05e90440 = 99157056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 30 00 00 05 e9 04 78 40 00 00:00:00.007 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e9 04 28 40 00 00:00:00.007 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e9 03 a8 40 00 00:00:00.007 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e9 03 28 40 00 00:00:00.007 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e9 02 a8 40 00 00:00:00.007 READ FPDMA QUEUED Error 332 [3] occurred at disk power-on lifetime: 14228 hours (592 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 38 00 00 05 e7 49 40 40 00 Error: ICRC, ABRT at LBA = 0x05e74940 = 99043648 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 50 00 00 05 e7 49 58 40 00 00:00:00.011 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e7 49 28 40 00 00:00:00.011 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e7 48 a8 40 00 00:00:00.011 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e7 48 28 40 00 00:00:00.011 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e7 47 a8 40 00 00:00:00.011 READ FPDMA QUEUED Error 331 [2] occurred at disk power-on lifetime: 14228 hours (592 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 08 00 00 00 01 22 7d c0 e0 00 Error: ICRC, ABRT 2048 sectors at LBA = 0x01227dc0 = 19037632 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 01 22 7d c0 e0 00 00:00:00.004 READ DMA EXT 25 00 00 08 00 00 00 00 e8 5e 80 e0 00 00:00:00.004 READ DMA EXT 25 00 00 08 00 00 00 00 e8 5e a8 e0 00 00:00:00.003 READ DMA EXT 25 00 00 08 00 00 00 01 22 7d 80 e0 00 00:00:00.003 READ DMA EXT 25 00 00 08 00 00 00 01 22 7d 90 e0 00 00:00:00.003 READ DMA EXT Error 330 [1] occurred at disk power-on lifetime: 14223 hours (592 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 ff b8 00 00 05 e2 d8 80 40 00 Error: ICRC, ABRT at LBA = 0x05e2d880 = 98752640 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 10 00 00 05 e2 d8 98 40 00 00:00:00.005 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e2 d8 28 40 00 00:00:00.005 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e2 d7 a8 40 00 00:00:00.005 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e2 d7 28 40 00 00:00:00.005 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e2 d6 a8 40 00 00:00:00.005 READ FPDMA QUEUED Error 329 [0] occurred at disk power-on lifetime: 14181 hours (590 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 28 00 00 05 ec 7f 40 40 00 Error: ICRC, ABRT at LBA = 0x05ec7f40 = 99385152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 05 ec 7f 68 40 00 00:00:00.008 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 ec 7f 28 40 00 00:00:00.008 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 ec 7e a8 40 00 00:00:00.008 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 ec 7e 28 40 00 00:00:00.008 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 ec 7d a8 40 00 00:00:00.008 READ FPDMA QUEUED Error 328 [7] occurred at disk power-on lifetime: 14165 hours (590 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 ff c8 00 00 05 eb c6 00 40 00 Error: ICRC, ABRT at LBA = 0x05ebc600 = 99337728 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 00 05 eb c6 08 40 00 00:00:00.188 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 eb c5 a8 40 00 00:00:00.188 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 eb c5 28 40 00 00:00:00.188 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 eb c4 a8 40 00 00:00:00.188 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 eb c4 28 40 00 00:00:00.188 READ FPDMA QUEUED Error 327 [6] occurred at disk power-on lifetime: 14165 hours (590 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 18 00 00 05 e6 e1 c0 40 00 Error: ICRC, ABRT at LBA = 0x05e6e1c0 = 99017152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 30 00 00 05 e6 e1 f8 40 00 00:00:00.006 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e6 e1 a8 40 00 00:00:00.006 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e6 e1 28 40 00 00:00:00.006 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e6 e0 a8 40 00 00:00:00.006 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 e6 e0 28 40 00 00:00:00.006 READ FPDMA QUEUED Error 326 [5] occurred at disk power-on lifetime: 14159 hours (589 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 ff c8 00 00 05 ec cd 00 40 00 Error: ICRC, ABRT at LBA = 0x05eccd00 = 99405056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 00 05 ec cd 08 40 00 00:00:00.008 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 ec cc a8 40 00 00:00:00.008 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 ec cc 28 40 00 00:00:00.008 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 ec cb a8 40 00 00:00:00.008 READ FPDMA QUEUED 60 00 00 00 80 00 00 05 ec cb 28 40 00 00:00:00.008 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 21/28 Celsius Lifetime Min/Max Temperature: 13/46 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (106) Index Estimated Time Temperature Celsius 107 2020-05-09 19:30 28 ********* 108 2020-05-09 19:35 31 ************ ... ..( 2 skipped). .. ************ 111 2020-05-09 19:50 31 ************ 112 2020-05-09 19:55 30 *********** 113 2020-05-09 20:00 27 ******** 114 2020-05-09 20:05 28 ********* 115 2020-05-09 20:10 29 ********** ... ..( 3 skipped). .. ********** 119 2020-05-09 20:30 29 ********** 120 2020-05-09 20:35 28 ********* ... ..( 6 skipped). .. ********* 127 2020-05-09 21:10 28 ********* 0 2020-05-09 21:15 27 ******** 1 2020-05-09 21:20 28 ********* ... ..( 8 skipped). .. ********* 10 2020-05-09 22:05 28 ********* 11 2020-05-09 22:10 27 ******** 12 2020-05-09 22:15 27 ******** 13 2020-05-09 22:20 28 ********* 14 2020-05-09 22:25 27 ******** ... ..( 15 skipped). .. ******** 30 2020-05-09 23:45 27 ******** 31 2020-05-09 23:50 28 ********* 32 2020-05-09 23:55 29 ********** 33 2020-05-10 00:00 29 ********** 34 2020-05-10 00:05 29 ********** 35 2020-05-10 00:10 30 *********** ... ..( 3 skipped). .. *********** 39 2020-05-10 00:30 30 *********** 40 2020-05-10 00:35 31 ************ ... ..( 11 skipped). .. ************ 52 2020-05-10 01:35 31 ************ 53 2020-05-10 01:40 30 *********** ... ..( 3 skipped). .. *********** 57 2020-05-10 02:00 30 *********** 58 2020-05-10 02:05 29 ********** ... ..( 6 skipped). .. ********** 65 2020-05-10 02:40 29 ********** 66 2020-05-10 02:45 28 ********* 67 2020-05-10 02:50 24 ***** 68 2020-05-10 02:55 25 ****** ... ..( 2 skipped). .. ****** 71 2020-05-10 03:10 25 ****** 72 2020-05-10 03:15 26 ******* ... ..( 2 skipped). .. ******* 75 2020-05-10 03:30 26 ******* 76 2020-05-10 03:35 27 ******** 77 2020-05-10 03:40 28 ********* ... ..( 28 skipped). .. ********* 106 2020-05-10 06:05 28 ********* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 68596 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific