/dev/nvme0n1 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.5-lqx2-1-lqx] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: WD Blue SN570 1TB Serial Number: -- Firmware Version: 234100WD PCI Vendor/Subsystem ID: 0x15b7 IEEE OUI Identifier: 0x001b44 Total NVM Capacity: 1,000,204,886,016 [1.00 TB] Unallocated NVM Capacity: 0 Controller ID: 0 NVMe Version: 1.4 Number of Namespaces: 1 Namespace 1 Size/Capacity: 1,000,204,886,016 [1.00 TB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 001b44 ... Local Time is: Fri Jan 13 18:47:16 2023 CET Firmware Updates (0x14): 2 Slots, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x005f): Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp Log Page Attributes (0x1e): Cmd_Eff_Lg Ext_Get_Lg Telmtry_Lg Pers_Ev_Lg Maximum Data Transfer Size: 128 Pages Warning Comp. Temp. Threshold: 80 Celsius Critical Comp. Temp. Threshold: 85 Celsius Namespace 1 Features (0x02): NA_Fields Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 4.20W 3.70W - 0 0 0 0 0 0 1 + 2.70W 2.30W - 0 0 0 0 0 0 2 + 1.90W 1.80W - 0 0 0 0 0 0 3 - 0.0250W - - 3 3 3 3 3900 11000 4 - 0.0050W - - 4 4 4 4 5000 44000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 2 1 - 4096 0 1 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 31 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 0% Data Units Read: 3,055,127 [1.56 TB] Data Units Written: 2,991,024 [1.53 TB] Host Read Commands: 58,765,047 Host Write Commands: 22,178,611 Controller Busy Time: 129 Power Cycles: 49 Power On Hours: 298 Unsafe Shutdowns: 32 Media and Data Integrity Errors: 0 Error Information Log Entries: 132 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Error Information (NVMe Log 0x01, 16 of 256 entries) No Errors Logged /dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.5-lqx2-1-lqx] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Laptop HDD Device Model: ST500LT012-9WS142 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0001LVM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Jan 13 18:47:16 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 101) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 116 099 034 - 110604544 3 Spin_Up_Time PO---- 100 099 000 - 0 4 Start_Stop_Count -O--CK 092 092 020 - 8685 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 8 7 Seek_Error_Rate POSR-- 086 060 030 - 4709186811 9 Power_On_Hours -O--CK 041 041 000 - 52266 (208 223 0) 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 094 094 020 - 6163 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 098 000 - 78 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 072 037 045 Past 28 (1 50 31 27 0) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 149 192 Power-Off_Retract_Count -O--CK 100 100 000 - 219 193 Load_Cycle_Count -O--CK 001 001 000 - 400600 194 Temperature_Celsius -O---K 028 063 000 - 28 (0 15 0 0 0) 196 Reallocated_Event_Count POSR-- 068 068 030 - 28603 (8275 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 198 000 - 85 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbd-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 373 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 373 [12] occurred at disk power-on lifetime: 51750 hours (2156 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 40 00 Device Fault; Error: ABRT at LBA = 0x00808781 = 8423297 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 04 00 00 00 03 28 40 40 00 00:03:44.032 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:03:43.164 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:03:43.101 SET FEATURES [Enable write cache] ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:03:43.100 SET FEATURES [Disable SATA feature] 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:03:43.030 NOP [Abort queued commands] Error 372 [11] occurred at disk power-on lifetime: 51750 hours (2156 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:03:43.164 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:03:43.101 SET FEATURES [Enable write cache] ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:03:43.100 SET FEATURES [Disable SATA feature] 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:03:43.030 NOP [Abort queued commands] 60 00 00 00 04 00 00 00 03 28 40 40 00 00:03:43.028 READ FPDMA QUEUED Error 371 [10] occurred at disk power-on lifetime: 51750 hours (2156 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:03:43.101 SET FEATURES [Enable write cache] ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:03:43.100 SET FEATURES [Disable SATA feature] 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:03:43.030 NOP [Abort queued commands] 60 00 00 00 04 00 00 00 03 28 40 40 00 00:03:43.028 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:03:43.028 SET FEATURES [Enable write cache] Error 370 [9] occurred at disk power-on lifetime: 51750 hours (2156 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:03:43.100 SET FEATURES [Disable SATA feature] 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:03:43.030 NOP [Abort queued commands] 60 00 00 00 04 00 00 00 03 28 40 40 00 00:03:43.028 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:03:43.028 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:03:42.936 NOP [Abort queued commands] Error 369 [8] occurred at disk power-on lifetime: 51750 hours (2156 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 40 00 Device Fault; Error: ABRT at LBA = 0x00808781 = 8423297 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 04 00 00 00 03 28 40 40 00 00:03:43.028 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:03:43.028 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:03:42.936 NOP [Abort queued commands] 60 00 00 00 01 00 00 00 03 28 00 40 00 00:03:42.888 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:03:42.033 SET FEATURES [Disable SATA feature] Error 368 [7] occurred at disk power-on lifetime: 51750 hours (2156 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:03:43.028 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:03:42.936 NOP [Abort queued commands] 60 00 00 00 01 00 00 00 03 28 00 40 00 00:03:42.888 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:03:42.033 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:03:42.032 SET FEATURES [Enable write cache] Error 367 [6] occurred at disk power-on lifetime: 51750 hours (2156 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 40 00 Device Fault; Error: ABRT at LBA = 0x00808781 = 8423297 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 03 28 00 40 00 00:03:42.888 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:03:42.033 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:03:42.032 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:03:41.926 NOP [Abort queued commands] 60 00 00 00 01 00 00 00 03 28 00 40 00 00:03:41.885 READ FPDMA QUEUED Error 366 [5] occurred at disk power-on lifetime: 51750 hours (2156 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:03:42.033 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:03:42.032 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:03:41.926 NOP [Abort queued commands] 60 00 00 00 01 00 00 00 03 28 00 40 00 00:03:41.885 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:03:41.041 SET FEATURES [Disable SATA feature] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 51517 - # 2 Conveyance offline Completed without error 00% 50995 - # 3 Short offline Completed without error 00% 50995 - # 4 Extended offline Completed without error 00% 40044 - # 5 Conveyance offline Completed without error 00% 40029 - # 6 Short offline Completed without error 00% 40029 - # 7 Short offline Completed without error 00% 38665 - # 8 Vendor (0x50) Completed without error 00% 36318 - # 9 Short offline Completed without error 00% 36318 - #10 Short offline Completed without error 00% 32837 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 27/31 Celsius Lifetime Min/Max Temperature: 15/63 Celsius Under/Over Temperature Limit Count: 0/10 Vendor specific: 00 00 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 11 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (95) Index Estimated Time Temperature Celsius 96 2023-01-12 19:29 32 ************* ... ..( 3 skipped). .. ************* 100 2023-01-12 20:13 32 ************* 101 2023-01-12 20:24 31 ************ 102 2023-01-12 20:35 31 ************ 103 2023-01-12 20:46 ? - 104 2023-01-12 20:57 27 ******** 105 2023-01-12 21:08 27 ******** 106 2023-01-12 21:19 31 ************ 107 2023-01-12 21:30 32 ************* 108 2023-01-12 21:41 29 ********** 109 2023-01-12 21:52 26 ******* ... ..( 3 skipped). .. ******* 113 2023-01-12 22:36 26 ******* 114 2023-01-12 22:47 25 ****** 115 2023-01-12 22:58 25 ****** 116 2023-01-12 23:09 25 ****** 117 2023-01-12 23:20 ? - 118 2023-01-12 23:31 24 ***** 119 2023-01-12 23:42 24 ***** 120 2023-01-12 23:53 ? - 121 2023-01-13 00:04 29 ********** 122 2023-01-13 00:15 ? - 123 2023-01-13 00:26 27 ******** 124 2023-01-13 00:37 ? - 125 2023-01-13 00:48 26 ******* 126 2023-01-13 00:59 26 ******* 127 2023-01-13 01:10 27 ******** 0 2023-01-13 01:21 27 ******** 1 2023-01-13 01:32 31 ************ 2 2023-01-13 01:43 32 ************* 3 2023-01-13 01:54 31 ************ 4 2023-01-13 02:05 29 ********** 5 2023-01-13 02:16 28 ********* 6 2023-01-13 02:27 27 ******** ... ..( 9 skipped). .. ******** 16 2023-01-13 04:17 27 ******** 17 2023-01-13 04:28 30 *********** 18 2023-01-13 04:39 ? - 19 2023-01-13 04:50 26 ******* 20 2023-01-13 05:01 26 ******* 21 2023-01-13 05:12 30 *********** 22 2023-01-13 05:23 29 ********** 23 2023-01-13 05:34 28 ********* ... ..( 3 skipped). .. ********* 27 2023-01-13 06:18 28 ********* 28 2023-01-13 06:29 29 ********** 29 2023-01-13 06:40 28 ********* 30 2023-01-13 06:51 28 ********* 31 2023-01-13 07:02 31 ************ 32 2023-01-13 07:13 32 ************* ... ..( 16 skipped). .. ************* 49 2023-01-13 10:20 32 ************* 50 2023-01-13 10:31 33 ************** ... ..( 2 skipped). .. ************** 53 2023-01-13 11:04 33 ************** 54 2023-01-13 11:15 ? - 55 2023-01-13 11:26 29 ********** 56 2023-01-13 11:37 28 ********* 57 2023-01-13 11:48 30 *********** 58 2023-01-13 11:59 31 ************ 59 2023-01-13 12:10 29 ********** 60 2023-01-13 12:21 28 ********* 61 2023-01-13 12:32 28 ********* 62 2023-01-13 12:43 28 ********* 63 2023-01-13 12:54 29 ********** 64 2023-01-13 13:05 31 ************ 65 2023-01-13 13:16 ? - 66 2023-01-13 13:27 30 *********** 67 2023-01-13 13:38 ? - 68 2023-01-13 13:49 31 ************ 69 2023-01-13 14:00 31 ************ 70 2023-01-13 14:11 33 ************** 71 2023-01-13 14:22 ? - 72 2023-01-13 14:33 29 ********** 73 2023-01-13 14:44 30 *********** 74 2023-01-13 14:55 32 ************* 75 2023-01-13 15:06 31 ************ 76 2023-01-13 15:17 32 ************* ... ..( 2 skipped). .. ************* 79 2023-01-13 15:50 32 ************* 80 2023-01-13 16:01 28 ********* 81 2023-01-13 16:12 ? - 82 2023-01-13 16:23 26 ******* 83 2023-01-13 16:34 ? - 84 2023-01-13 16:45 26 ******* 85 2023-01-13 16:56 ? - 86 2023-01-13 17:07 27 ******** 87 2023-01-13 17:18 27 ******** 88 2023-01-13 17:29 29 ********** 89 2023-01-13 17:40 30 *********** 90 2023-01-13 17:51 29 ********** 91 2023-01-13 18:02 28 ********* ... ..( 3 skipped). .. ********* 95 2023-01-13 18:46 28 ********* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS