Probe #5c0129ab3f of ASUSTek PRIME B450-PLUS Desktop Computer

Log: smartctl

/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.75-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: WD Blue / Red / Green SSDs Device Model: WDC WDS120G2G0A-00JH30 Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: UE500000 User Capacity: 120,040,980,480 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Dec 2 19:53:01 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 32) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x15) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 21) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 4814 12 Power_Cycle_Count -O--CK 100 100 000 - 1179 165 Block_Erase_Count -O--CK 100 100 000 - 10033 166 Minimum_PE_Cycles_TLC -O--CK 100 100 --- - 83 167 Max_Bad_Blocks_per_Die -O--CK 100 100 --- - 0 168 Maximum_PE_Cycles_TLC -O--CK 100 100 --- - 104 169 Total_Bad_Blocks -O--CK 100 100 --- - 180 170 Grown_Bad_Blocks -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Average_PE_Cycles_TLC -O--CK 100 100 000 - 83 174 Unexpected_Power_Loss -O--CK 100 100 000 - 85 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 064 050 000 - 36 (Min/Max 15/50) 199 UDMA_CRC_Error_Count -O--CK 100 100 --- - 0 230 Media_Wearout_Indicator -O--CK 100 100 000 - 0x1c42103c1c42 232 Available_Reservd_Space PO--CK 100 100 005 - 100 233 NAND_GB_Written_TLC -O--CK 100 100 --- - 9833 234 NAND_GB_Written_SLC -O--CK 100 100 000 - 55812 241 Host_Writes_GiB ----CK 100 100 000 - 19184 242 Host_Reads_GiB ----CK 100 100 000 - 15034 244 Temp_Throttle_Status -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log 0xa7 GPL,SL VS 1 Device vendor specific log 0xa9 GPL,SL VS 3 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 3594 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1179 --- Lifetime Power-On Resets 0x01 0x010 4 4814 --- Power-on Hours 0x01 0x018 6 40232302080 --- Logical Sectors Written 0x01 0x028 6 31530656627 --- Logical Sectors Read 0x01 0x038 6 4814 --- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 36 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 49 --- Highest Temperature 0x05 0x028 1 30 --- Lowest Temperature 0x05 0x030 1 - --- Highest Average Short Term Temperature 0x05 0x038 1 - --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 16 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.75-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Black Device Model: WDC WD6401AALS-00J7B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 05.00K05 User Capacity: 640,135,028,736 bytes [640 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Fri Dec 2 19:53:01 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12780) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 149) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 199 199 051 - 64700 3 Spin_Up_Time POS--K 225 218 021 - 8733 4 Start_Stop_Count -O--CK 095 095 000 - 5610 5 Reallocated_Sector_Ct PO--CK 162 162 140 - 303 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 080 080 000 - 14608 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4321 192 Power-Off_Retract_Count -O--CK 199 199 000 - 1033 193 Load_Cycle_Count -O--CK 199 199 000 - 5538 194 Temperature_Celsius -O---K 112 100 000 - 38 196 Reallocated_Event_Count -O--CK 001 001 000 - 257 197 Current_Pending_Sector -O--CK 200 193 000 - 53 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 120 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2074 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2074 [9] occurred at disk power-on lifetime: 11076 hours (461 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 2a fe b2 40 00 Error: UNC at LBA = 0x012afeb2 = 19594930 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 e0 00 f0 00 00 01 2a fe 87 40 00 02:38:59.347 READ FPDMA QUEUED 60 00 08 00 e8 00 00 01 2a fe 7f 40 00 02:38:59.347 READ FPDMA QUEUED 60 00 08 00 e0 00 00 01 2a fe 77 40 00 02:38:59.255 READ FPDMA QUEUED 60 00 10 00 d8 00 00 01 2a fe 67 40 00 02:38:59.176 READ FPDMA QUEUED 61 00 08 00 d0 00 00 01 cf 9c 5f 40 00 02:38:59.176 WRITE FPDMA QUEUED Error 2073 [8] occurred at disk power-on lifetime: 11076 hours (461 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 2a f0 95 40 00 Error: UNC at LBA = 0x012af095 = 19591317 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 0a 00 b8 00 00 01 2a ff af 40 00 02:38:51.246 READ FPDMA QUEUED 60 00 f8 00 b0 00 00 01 2a ef ef 40 00 02:38:51.246 READ FPDMA QUEUED 60 00 08 00 a8 00 00 01 2a ef e7 40 00 02:38:51.166 READ FPDMA QUEUED 61 00 08 00 a0 00 00 01 79 53 af 40 00 02:38:48.316 WRITE FPDMA QUEUED 60 00 10 00 98 00 00 01 4b 91 7f 40 00 02:38:46.042 READ FPDMA QUEUED Error 2072 [7] occurred at disk power-on lifetime: 11070 hours (461 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 42 04 9e bb 40 00 Error: UNC at LBA = 0x42049ebb = 1107599035 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 b0 00 00 42 04 9e a8 40 00 00:08:37.385 READ FPDMA QUEUED 60 00 40 00 a8 00 00 00 ea 61 07 40 00 00:08:37.368 READ FPDMA QUEUED 61 00 10 00 a0 00 00 00 7f b2 6f 40 00 00:08:37.368 WRITE FPDMA QUEUED 60 00 3f 00 98 00 00 42 0f 88 d0 40 00 00:08:36.816 READ FPDMA QUEUED 60 00 40 00 90 00 00 00 ea 57 87 40 00 00:08:36.801 READ FPDMA QUEUED Error 2071 [6] occurred at disk power-on lifetime: 11070 hours (461 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 42 04 9e e8 40 00 Error: UNC at LBA = 0x42049ee8 = 1107599080 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 d0 00 00 42 04 9e e8 40 00 00:08:32.489 READ FPDMA QUEUED 60 00 3a 00 c8 00 00 3a ed 30 c0 40 00 00:08:32.477 READ FPDMA QUEUED 61 00 10 00 c0 00 00 00 7f b1 47 40 00 00:08:32.477 WRITE FPDMA QUEUED 60 00 40 00 b8 00 00 42 04 9d 90 40 00 00:08:30.987 READ FPDMA QUEUED 61 00 08 00 b0 00 00 00 7f b0 df 40 00 00:08:30.986 WRITE FPDMA QUEUED Error 2070 [5] occurred at disk power-on lifetime: 11070 hours (461 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 23 2b 64 93 40 00 Error: UNC at LBA = 0x232b6493 = 590046355 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 a8 00 00 23 2b 64 90 40 00 00:07:01.401 READ FPDMA QUEUED 60 00 08 00 a0 00 00 23 2b 64 88 40 00 00:06:59.136 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:06:59.136 READ LOG EXT 60 00 08 00 98 00 00 23 2b 64 80 40 00 00:06:56.822 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:06:56.822 READ LOG EXT Error 2069 [4] occurred at disk power-on lifetime: 11070 hours (461 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 23 2b 64 82 40 00 Error: UNC at LBA = 0x232b6482 = 590046338 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 98 00 00 23 2b 64 80 40 00 00:06:56.822 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:06:56.822 READ LOG EXT 60 00 08 00 90 00 00 23 2b 64 78 40 00 00:06:54.208 READ FPDMA QUEUED 60 00 08 00 88 00 00 23 2b 64 70 40 00 00:06:53.117 READ FPDMA QUEUED 60 00 08 00 80 00 00 23 2b 64 68 40 00 00:06:53.100 READ FPDMA QUEUED Error 2068 [3] occurred at disk power-on lifetime: 11070 hours (461 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 23 2b 64 78 40 00 Error: UNC at LBA = 0x232b6478 = 590046328 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 90 00 00 23 2b 64 78 40 00 00:06:54.208 READ FPDMA QUEUED 60 00 08 00 88 00 00 23 2b 64 70 40 00 00:06:53.117 READ FPDMA QUEUED 60 00 08 00 80 00 00 23 2b 64 68 40 00 00:06:53.100 READ FPDMA QUEUED 60 00 08 00 78 00 00 23 2b 64 60 40 00 00:06:53.068 READ FPDMA QUEUED 60 00 08 00 70 00 00 23 2b 64 58 40 00 00:06:53.068 READ FPDMA QUEUED Error 2067 [2] occurred at disk power-on lifetime: 11070 hours (461 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 23 2b 63 d1 40 00 Error: UNC at LBA = 0x232b63d1 = 590046161 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e0 00 00 23 2b 63 d0 40 00 00:06:45.583 READ FPDMA QUEUED 60 00 08 00 d8 00 00 23 2b 63 c8 40 00 00:06:44.117 READ FPDMA QUEUED 60 00 08 00 d0 00 00 23 2b 63 c0 40 00 00:06:43.135 READ FPDMA QUEUED 60 00 08 00 c8 00 00 23 2b 63 b8 40 00 00:06:43.126 READ FPDMA QUEUED 60 00 08 00 c0 00 00 23 2b 63 b0 40 00 00:06:43.018 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 12267 - # 2 Short offline Completed without error 00% 12168 - # 3 Short offline Completed without error 00% 9799 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 24/38 Celsius Lifetime Min/Max Temperature: 25/50 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (13) Index Estimated Time Temperature Celsius 14 2022-12-02 17:46 38 ******************* ... ..( 12 skipped). .. ******************* 27 2022-12-02 17:59 38 ******************* 28 2022-12-02 18:00 39 ******************** ... ..( 24 skipped). .. ******************** 53 2022-12-02 18:25 39 ******************** 54 2022-12-02 18:26 40 ********************* ... ..( 38 skipped). .. ********************* 93 2022-12-02 19:05 40 ********************* 94 2022-12-02 19:06 ? - 95 2022-12-02 19:07 24 ***** 96 2022-12-02 19:08 25 ****** 97 2022-12-02 19:09 26 ******* 98 2022-12-02 19:10 26 ******* 99 2022-12-02 19:11 27 ******** 100 2022-12-02 19:12 28 ********* 101 2022-12-02 19:13 29 ********** 102 2022-12-02 19:14 29 ********** 103 2022-12-02 19:15 30 *********** 104 2022-12-02 19:16 30 *********** 105 2022-12-02 19:17 30 *********** 106 2022-12-02 19:18 31 ************ 107 2022-12-02 19:19 32 ************* 108 2022-12-02 19:20 32 ************* 109 2022-12-02 19:21 33 ************** ... ..( 2 skipped). .. ************** 112 2022-12-02 19:24 33 ************** 113 2022-12-02 19:25 34 *************** ... ..( 3 skipped). .. *************** 117 2022-12-02 19:29 34 *************** 118 2022-12-02 19:30 35 **************** 119 2022-12-02 19:31 35 **************** 120 2022-12-02 19:32 35 **************** 121 2022-12-02 19:33 36 ***************** ... ..( 2 skipped). .. ***************** 124 2022-12-02 19:36 36 ***************** 125 2022-12-02 19:37 37 ****************** ... ..( 12 skipped). .. ****************** 10 2022-12-02 19:50 37 ****************** 11 2022-12-02 19:51 38 ******************* 12 2022-12-02 19:52 38 ******************* 13 2022-12-02 19:53 38 ******************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 2825 Vendor specific /dev/sdc smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.75-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-00BBHA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Dec 2 19:53:01 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10440) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 109) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 176 175 021 - 2175 4 Start_Stop_Count -O--CK 100 100 000 - 784 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 099 099 000 - 1216 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 312 192 Power-Off_Retract_Count -O--CK 200 200 000 - 2 193 Load_Cycle_Count -O--CK 200 200 000 - 2782 194 Temperature_Celsius -O---K 108 102 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 74 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 24/35 Celsius Lifetime Min/Max Temperature: 22/41 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (421) Index Estimated Time Temperature Celsius 422 2022-12-02 11:56 36 ***************** 423 2022-12-02 11:57 36 ***************** 424 2022-12-02 11:58 ? - 425 2022-12-02 11:59 24 ***** 426 2022-12-02 12:00 24 ***** 427 2022-12-02 12:01 25 ****** 428 2022-12-02 12:02 25 ****** 429 2022-12-02 12:03 26 ******* 430 2022-12-02 12:04 27 ******** 431 2022-12-02 12:05 27 ******** 432 2022-12-02 12:06 28 ********* 433 2022-12-02 12:07 28 ********* 434 2022-12-02 12:08 29 ********** 435 2022-12-02 12:09 29 ********** 436 2022-12-02 12:10 29 ********** 437 2022-12-02 12:11 30 *********** 438 2022-12-02 12:12 30 *********** 439 2022-12-02 12:13 31 ************ ... ..( 2 skipped). .. ************ 442 2022-12-02 12:16 31 ************ 443 2022-12-02 12:17 32 ************* ... ..( 3 skipped). .. ************* 447 2022-12-02 12:21 32 ************* 448 2022-12-02 12:22 33 ************** ... ..( 11 skipped). .. ************** 460 2022-12-02 12:34 33 ************** 461 2022-12-02 12:35 34 *************** ... ..( 4 skipped). .. *************** 466 2022-12-02 12:40 34 *************** 467 2022-12-02 12:41 35 **************** ... ..( 3 skipped). .. **************** 471 2022-12-02 12:45 35 **************** 472 2022-12-02 12:46 36 ***************** ... ..( 6 skipped). .. ***************** 1 2022-12-02 12:53 36 ***************** 2 2022-12-02 12:54 ? - 3 2022-12-02 12:55 24 ***** 4 2022-12-02 12:56 24 ***** 5 2022-12-02 12:57 25 ****** 6 2022-12-02 12:58 25 ****** 7 2022-12-02 12:59 26 ******* 8 2022-12-02 13:00 27 ******** 9 2022-12-02 13:01 27 ******** 10 2022-12-02 13:02 28 ********* 11 2022-12-02 13:03 28 ********* 12 2022-12-02 13:04 29 ********** 13 2022-12-02 13:05 29 ********** 14 2022-12-02 13:06 29 ********** 15 2022-12-02 13:07 30 *********** 16 2022-12-02 13:08 30 *********** 17 2022-12-02 13:09 31 ************ 18 2022-12-02 13:10 31 ************ 19 2022-12-02 13:11 31 ************ 20 2022-12-02 13:12 32 ************* ... ..( 2 skipped). .. ************* 23 2022-12-02 13:15 32 ************* 24 2022-12-02 13:16 33 ************** ... ..( 9 skipped). .. ************** 34 2022-12-02 13:26 33 ************** 35 2022-12-02 13:27 34 *************** ... ..( 4 skipped). .. *************** 40 2022-12-02 13:32 34 *************** 41 2022-12-02 13:33 35 **************** ... ..( 11 skipped). .. **************** 53 2022-12-02 13:45 35 **************** 54 2022-12-02 13:46 36 ***************** ... ..( 11 skipped). .. ***************** 66 2022-12-02 13:58 36 ***************** 67 2022-12-02 13:59 35 **************** ... ..( 22 skipped). .. **************** 90 2022-12-02 14:22 35 **************** 91 2022-12-02 14:23 34 *************** ... ..( 10 skipped). .. *************** 102 2022-12-02 14:34 34 *************** 103 2022-12-02 14:35 35 **************** ... ..( 24 skipped). .. **************** 128 2022-12-02 15:00 35 **************** 129 2022-12-02 15:01 34 *************** ... ..( 2 skipped). .. *************** 132 2022-12-02 15:04 34 *************** 133 2022-12-02 15:05 35 **************** ... ..( 11 skipped). .. **************** 145 2022-12-02 15:17 35 **************** 146 2022-12-02 15:18 36 ***************** ... ..( 12 skipped). .. ***************** 159 2022-12-02 15:31 36 ***************** 160 2022-12-02 15:32 35 **************** ... ..( 27 skipped). .. **************** 188 2022-12-02 16:00 35 **************** 189 2022-12-02 16:01 34 *************** 190 2022-12-02 16:02 34 *************** 191 2022-12-02 16:03 34 *************** 192 2022-12-02 16:04 35 **************** ... ..( 8 skipped). .. **************** 201 2022-12-02 16:13 35 **************** 202 2022-12-02 16:14 36 ***************** ... ..( 7 skipped). .. ***************** 210 2022-12-02 16:22 36 ***************** 211 2022-12-02 16:23 ? - 212 2022-12-02 16:24 24 ***** 213 2022-12-02 16:25 24 ***** 214 2022-12-02 16:26 25 ****** 215 2022-12-02 16:27 26 ******* 216 2022-12-02 16:28 26 ******* 217 2022-12-02 16:29 27 ******** 218 2022-12-02 16:30 27 ******** 219 2022-12-02 16:31 28 ********* 220 2022-12-02 16:32 28 ********* 221 2022-12-02 16:33 29 ********** 222 2022-12-02 16:34 29 ********** 223 2022-12-02 16:35 30 *********** 224 2022-12-02 16:36 30 *********** 225 2022-12-02 16:37 30 *********** 226 2022-12-02 16:38 31 ************ 227 2022-12-02 16:39 31 ************ 228 2022-12-02 16:40 31 ************ 229 2022-12-02 16:41 32 ************* ... ..( 7 skipped). .. ************* 237 2022-12-02 16:49 32 ************* 238 2022-12-02 16:50 33 ************** ... ..( 4 skipped). .. ************** 243 2022-12-02 16:55 33 ************** 244 2022-12-02 16:56 34 *************** ... ..( 21 skipped). .. *************** 266 2022-12-02 17:18 34 *************** 267 2022-12-02 17:19 35 **************** ... ..( 34 skipped). .. **************** 302 2022-12-02 17:54 35 **************** 303 2022-12-02 17:55 34 *************** ... ..( 11 skipped). .. *************** 315 2022-12-02 18:07 34 *************** 316 2022-12-02 18:08 35 **************** ... ..( 27 skipped). .. **************** 344 2022-12-02 18:36 35 **************** 345 2022-12-02 18:37 36 ***************** ... ..( 32 skipped). .. ***************** 378 2022-12-02 19:10 36 ***************** 379 2022-12-02 19:11 35 **************** ... ..( 11 skipped). .. **************** 391 2022-12-02 19:23 35 **************** 392 2022-12-02 19:24 36 ***************** ... ..( 28 skipped). .. ***************** 421 2022-12-02 19:53 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 2823 Vendor specific


Hardware for Linux and BSD

GitHub