/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.15.0-desktop-94.1rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST3250318AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC37 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Apr 30 20:50:56 2020 EEST ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213891en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 0 (vendor specific), recommended: 254 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 617) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 49) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 109 096 006 - 22377664 3 Spin_Up_Time PO---- 097 096 000 - 0 4 Start_Stop_Count -O--CK 093 093 020 - 7950 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 078 060 030 - 65536221 9 Power_On_Hours -O--CK 096 096 000 - 3985 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4867 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 125 188 Command_Timeout -O--CK 100 098 000 - 142 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 072 060 045 - 28 (Min/Max 25/28) 194 Temperature_Celsius -O---K 028 040 000 - 28 (0 16 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 056 037 000 - 22377664 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 7102 (85 164 0) 241 Total_LBAs_Written ------ 100 253 000 - 2662843501 242 Total_LBAs_Read ------ 100 253 000 - 1457654306 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 117 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 117 [16] occurred at disk power-on lifetime: 3076 hours (128 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1e 00 e5 a3 00 00 Error: UNC at LBA = 0x11e00e5a3 = 4798342563 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 03 00 00 01 00 01 1e 00 e5 a3 e0 00 00:06:02.694 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 00 00 00 00 00 e0 00 00:06:02.694 READ DMA EXT 42 03 00 00 02 00 01 1e 00 e5 a5 e0 00 00:06:02.688 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 00 00 00 00 00 e0 00 00:06:02.642 READ DMA EXT 42 03 00 00 02 00 01 1e 00 e5 a3 e0 00 00:05:59.633 READ VERIFY SECTOR(S) EXT Error 116 [15] occurred at disk power-on lifetime: 3076 hours (128 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1e 00 e5 a3 00 00 Error: UNC at LBA = 0x11e00e5a3 = 4798342563 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 03 00 00 02 00 01 1e 00 e5 a3 e0 00 00:05:59.633 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 00 00 00 00 00 e0 00 00:05:59.545 READ DMA EXT 42 03 00 00 04 00 01 1e 00 e5 a3 e0 00 00:05:56.525 READ VERIFY SECTOR(S) EXT 42 03 00 00 04 00 01 1e 00 e5 9f e0 00 00:05:56.516 READ VERIFY SECTOR(S) EXT 42 03 00 00 08 00 01 1e 00 e5 a7 e0 00 00:05:56.503 READ VERIFY SECTOR(S) EXT Error 115 [14] occurred at disk power-on lifetime: 3076 hours (128 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1e 00 e5 a3 00 00 Error: UNC at LBA = 0x11e00e5a3 = 4798342563 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 03 00 00 04 00 01 1e 00 e5 a3 e0 00 00:05:56.525 READ VERIFY SECTOR(S) EXT 42 03 00 00 04 00 01 1e 00 e5 9f e0 00 00:05:56.516 READ VERIFY SECTOR(S) EXT 42 03 00 00 08 00 01 1e 00 e5 a7 e0 00 00:05:56.503 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 11 e0 00 16 f7 e0 00 00:05:56.464 READ DMA EXT 42 03 00 00 08 00 01 1e 00 e5 9f e0 00 00:05:53.436 READ VERIFY SECTOR(S) EXT Error 114 [13] occurred at disk power-on lifetime: 3076 hours (128 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1e 00 e5 a3 00 00 Error: UNC at LBA = 0x11e00e5a3 = 4798342563 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 03 00 00 08 00 01 1e 00 e5 9f e0 00 00:05:53.436 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 06 79 00 1a a4 e0 00 00:05:53.436 READ DMA EXT 42 03 00 00 10 00 01 1e 00 e5 af e0 00 00:05:53.422 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 06 79 00 1a 66 e0 00 00:05:53.325 READ DMA EXT 42 03 00 00 10 00 01 1e 00 e5 9f e0 00 00:05:50.300 READ VERIFY SECTOR(S) EXT Error 113 [12] occurred at disk power-on lifetime: 3076 hours (128 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1e 00 e5 a3 00 00 Error: UNC at LBA = 0x11e00e5a3 = 4798342563 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 03 00 00 10 00 01 1e 00 e5 9f e0 00 00:05:50.300 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 00 00 00 00 00 e0 00 00:05:50.253 READ DMA EXT 42 03 00 00 20 00 01 1e 00 e5 9f e0 00 00:05:47.259 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 00 00 00 00 00 e0 00 00:05:47.258 READ DMA EXT 42 03 00 00 20 00 01 1e 00 e5 7f e0 00 00:05:47.253 READ VERIFY SECTOR(S) EXT Error 112 [11] occurred at disk power-on lifetime: 3076 hours (128 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1e 00 e5 a3 00 00 Error: UNC at LBA = 0x11e00e5a3 = 4798342563 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 03 00 00 20 00 01 1e 00 e5 9f e0 00 00:05:47.259 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 00 00 00 00 00 e0 00 00:05:47.258 READ DMA EXT 42 03 00 00 20 00 01 1e 00 e5 7f e0 00 00:05:47.253 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 00 00 00 00 00 e0 00 00:05:47.156 READ DMA EXT 42 03 00 00 40 00 01 1e 00 e5 7f e0 00 00:05:44.140 READ VERIFY SECTOR(S) EXT Error 111 [10] occurred at disk power-on lifetime: 3076 hours (128 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1e 00 e5 a3 00 00 Error: UNC at LBA = 0x11e00e5a3 = 4798342563 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 03 00 00 40 00 01 1e 00 e5 7f e0 00 00:05:44.140 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 11 e0 00 16 f7 e0 00 00:05:44.128 READ DMA EXT 42 03 00 00 40 00 01 1e 00 e5 3f e0 00 00:05:44.120 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 06 79 00 1a a4 e0 00 00:05:44.120 READ DMA EXT 42 03 00 00 80 00 01 1e 00 e5 bf e0 00 00:05:44.106 READ VERIFY SECTOR(S) EXT Error 110 [9] occurred at disk power-on lifetime: 3076 hours (128 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1e 00 e5 a3 00 00 Error: UNC at LBA = 0x11e00e5a3 = 4798342563 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 03 00 01 00 00 01 1e 00 e5 3f e0 00 00:05:37.895 READ VERIFY SECTOR(S) EXT 25 03 00 00 01 00 00 00 00 00 00 e0 00 00:05:37.865 READ DMA EXT 42 00 00 02 00 00 01 1e 00 e5 3f 40 00 00:05:34.836 READ VERIFY SECTOR(S) EXT 42 03 00 02 00 00 01 18 00 e5 3f e0 00 00:05:34.821 READ VERIFY SECTOR(S) EXT 42 03 00 02 00 00 01 20 00 d5 3f e0 00 00:05:29.737 READ VERIFY SECTOR(S) EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5 - # 2 Short offline Completed without error 00% 3 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 25/28 Celsius Lifetime Min/Max Temperature: 16/40 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (45) Index Estimated Time Temperature Celsius 46 2020-04-25 15:24 19 - 47 2020-04-25 16:23 ? - 48 2020-04-25 17:22 23 **** 49 2020-04-25 18:21 23 **** 50 2020-04-25 19:20 ? - 51 2020-04-25 20:19 21 ** 52 2020-04-25 21:18 21 ** 53 2020-04-25 22:17 ? - 54 2020-04-25 23:16 27 ******** 55 2020-04-26 00:15 27 ******** 56 2020-04-26 01:14 27 ******** 57 2020-04-26 02:13 26 ******* 58 2020-04-26 03:12 27 ******** 59 2020-04-26 04:11 ? - 60 2020-04-26 05:10 25 ****** 61 2020-04-26 06:09 25 ****** 62 2020-04-26 07:08 28 ********* 63 2020-04-26 08:07 27 ******** ... ..( 5 skipped). .. ******** 69 2020-04-26 14:01 27 ******** 70 2020-04-26 15:00 ? - 71 2020-04-26 15:59 19 - 72 2020-04-26 16:58 19 - 73 2020-04-26 17:57 24 ***** 74 2020-04-26 18:56 25 ****** 75 2020-04-26 19:55 ? - 76 2020-04-26 20:54 24 ***** 77 2020-04-26 21:53 ? - 78 2020-04-26 22:52 26 ******* 79 2020-04-26 23:51 26 ******* 80 2020-04-27 00:50 27 ******** ... ..( 3 skipped). .. ******** 84 2020-04-27 04:46 27 ******** 85 2020-04-27 05:45 ? - 86 2020-04-27 06:44 19 - 87 2020-04-27 07:43 ? - 88 2020-04-27 08:42 23 **** 89 2020-04-27 09:41 23 **** 90 2020-04-27 10:40 26 ******* 91 2020-04-27 11:39 26 ******* 92 2020-04-27 12:38 ? - 93 2020-04-27 13:37 25 ****** 94 2020-04-27 14:36 ? - 95 2020-04-27 15:35 25 ****** 96 2020-04-27 16:34 25 ****** 97 2020-04-27 17:33 27 ******** 98 2020-04-27 18:32 28 ********* 99 2020-04-27 19:31 28 ********* 100 2020-04-27 20:30 28 ********* 101 2020-04-27 21:29 27 ******** 102 2020-04-27 22:28 27 ******** 103 2020-04-27 23:27 27 ******** 104 2020-04-28 00:26 26 ******* 105 2020-04-28 01:25 27 ******** 106 2020-04-28 02:24 27 ******** 107 2020-04-28 03:23 27 ******** 108 2020-04-28 04:22 ? - 109 2020-04-28 05:21 19 - 110 2020-04-28 06:20 19 - 111 2020-04-28 07:19 24 ***** 112 2020-04-28 08:18 ? - 113 2020-04-28 09:17 19 - 114 2020-04-28 10:16 19 - 115 2020-04-28 11:15 ? - 116 2020-04-28 12:14 20 * 117 2020-04-28 13:13 20 * 118 2020-04-28 14:12 27 ******** ... ..( 2 skipped). .. ******** 121 2020-04-28 17:09 27 ******** 122 2020-04-28 18:08 ? - 123 2020-04-28 19:07 27 ******** 124 2020-04-28 20:06 ? - 125 2020-04-28 21:05 26 ******* 126 2020-04-28 22:04 26 ******* 127 2020-04-28 23:03 27 ******** ... ..( 3 skipped). .. ******** 3 2020-04-29 02:59 27 ******** 4 2020-04-29 03:58 ? - 5 2020-04-29 04:57 19 - 6 2020-04-29 05:56 ? - 7 2020-04-29 06:55 24 ***** 8 2020-04-29 07:54 24 ***** 9 2020-04-29 08:53 ? - 10 2020-04-29 09:52 21 ** 11 2020-04-29 10:51 21 ** 12 2020-04-29 11:50 27 ******** 13 2020-04-29 12:49 27 ******** 14 2020-04-29 13:48 29 ********** 15 2020-04-29 14:47 28 ********* 16 2020-04-29 15:46 27 ******** 17 2020-04-29 16:45 27 ******** 18 2020-04-29 17:44 26 ******* 19 2020-04-29 18:43 27 ******** 20 2020-04-29 19:42 27 ******** 21 2020-04-29 20:41 26 ******* 22 2020-04-29 21:40 26 ******* 23 2020-04-29 22:39 27 ******** 24 2020-04-29 23:38 26 ******* 25 2020-04-30 00:37 ? - 26 2020-04-30 01:36 20 * 27 2020-04-30 02:35 20 * 28 2020-04-30 03:34 26 ******* 29 2020-04-30 04:33 27 ******** 30 2020-04-30 05:32 ? - 31 2020-04-30 06:31 25 ****** 32 2020-04-30 07:30 25 ****** 33 2020-04-30 08:29 27 ******** 34 2020-04-30 09:28 ? - 35 2020-04-30 10:27 28 ********* 36 2020-04-30 11:26 28 ********* 37 2020-04-30 12:25 28 ********* 38 2020-04-30 13:24 29 ********** 39 2020-04-30 14:23 ? - 40 2020-04-30 15:22 27 ******** 41 2020-04-30 16:21 ? - 42 2020-04-30 17:20 25 ****** 43 2020-04-30 18:19 25 ****** 44 2020-04-30 19:18 28 ********* 45 2020-04-30 20:17 28 ********* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 23 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS