/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.6.2-101.fc38.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron Client SSDs Device Model: CT500MX500SSD1 Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: M3CR023 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Nov 29 21:41:02 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 0 5 Reallocate_NAND_Blk_Cnt -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 11609 12 Power_Cycle_Count -O--CK 100 100 000 - 1866 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Ave_Block-Erase_Count -O--CK 080 080 000 - 314 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 31 180 Unused_Reserve_NAND_Blk PO--CK 000 000 000 - 43 183 SATA_Interfac_Downshift -O--CK 100 100 000 - 0 184 Error_Correction_Count -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 057 040 000 - 43 (Min/Max 0/60) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_ECC_Cnt -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 202 Percent_Lifetime_Remain ----CK 080 080 001 - 20 206 Write_Error_Rate -OSR-- 100 100 000 - 0 210 Success_RAIN_Recov_Cnt -O--CK 100 100 000 - 0 246 Total_LBAs_Written -O--CK 100 100 000 - 81932583864 247 Host_Program_Page_Count -O--CK 100 100 000 - 1375449056 248 FTL_Program_Page_Count -O--CK 100 100 000 - 1490849551 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 64 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Completed [00% left] (0-65535) Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 43 Celsius Power Cycle Min/Max Temperature: 25/48 Celsius Lifetime Min/Max Temperature: 0/60 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: 0/100 Celsius Temperature History Size (Index): 128 (114) Index Estimated Time Temperature Celsius 115 2023-11-29 19:34 41 ********************** 116 2023-11-29 19:35 43 ************************ 117 2023-11-29 19:36 45 ************************** 118 2023-11-29 19:37 41 ********************** 119 2023-11-29 19:38 43 ************************ 120 2023-11-29 19:39 41 ********************** 121 2023-11-29 19:40 43 ************************ 122 2023-11-29 19:41 43 ************************ 123 2023-11-29 19:42 41 ********************** 124 2023-11-29 19:43 43 ************************ 125 2023-11-29 19:44 43 ************************ 126 2023-11-29 19:45 43 ************************ 127 2023-11-29 19:46 41 ********************** 0 2023-11-29 19:47 43 ************************ 1 2023-11-29 19:48 45 ************************** 2 2023-11-29 19:49 43 ************************ 3 2023-11-29 19:50 43 ************************ 4 2023-11-29 19:51 41 ********************** 5 2023-11-29 19:52 41 ********************** 6 2023-11-29 19:53 41 ********************** 7 2023-11-29 19:54 43 ************************ 8 2023-11-29 19:55 41 ********************** 9 2023-11-29 19:56 41 ********************** 10 2023-11-29 19:57 41 ********************** 11 2023-11-29 19:58 43 ************************ 12 2023-11-29 19:59 43 ************************ 13 2023-11-29 20:00 41 ********************** ... ..( 4 skipped). .. ********************** 18 2023-11-29 20:05 41 ********************** 19 2023-11-29 20:06 43 ************************ 20 2023-11-29 20:07 43 ************************ 21 2023-11-29 20:08 41 ********************** ... ..( 7 skipped). .. ********************** 29 2023-11-29 20:16 41 ********************** 30 2023-11-29 20:17 43 ************************ 31 2023-11-29 20:18 41 ********************** 32 2023-11-29 20:19 43 ************************ 33 2023-11-29 20:20 41 ********************** 34 2023-11-29 20:21 43 ************************ 35 2023-11-29 20:22 41 ********************** ... ..( 10 skipped). .. ********************** 46 2023-11-29 20:33 41 ********************** 47 2023-11-29 20:34 43 ************************ 48 2023-11-29 20:35 41 ********************** ... ..( 2 skipped). .. ********************** 51 2023-11-29 20:38 41 ********************** 52 2023-11-29 20:39 43 ************************ 53 2023-11-29 20:40 41 ********************** 54 2023-11-29 20:41 43 ************************ 55 2023-11-29 20:42 41 ********************** 56 2023-11-29 20:43 43 ************************ 57 2023-11-29 20:44 41 ********************** 58 2023-11-29 20:45 45 ************************** 59 2023-11-29 20:46 43 ************************ 60 2023-11-29 20:47 41 ********************** 61 2023-11-29 20:48 43 ************************ ... ..( 3 skipped). .. ************************ 65 2023-11-29 20:52 43 ************************ 66 2023-11-29 20:53 41 ********************** 67 2023-11-29 20:54 41 ********************** 68 2023-11-29 20:55 41 ********************** 69 2023-11-29 20:56 43 ************************ 70 2023-11-29 20:57 41 ********************** 71 2023-11-29 20:58 41 ********************** 72 2023-11-29 20:59 43 ************************ 73 2023-11-29 21:00 43 ************************ 74 2023-11-29 21:01 43 ************************ 75 2023-11-29 21:02 41 ********************** 76 2023-11-29 21:03 43 ************************ 77 2023-11-29 21:04 43 ************************ 78 2023-11-29 21:05 41 ********************** ... ..( 2 skipped). .. ********************** 81 2023-11-29 21:08 41 ********************** 82 2023-11-29 21:09 43 ************************ 83 2023-11-29 21:10 41 ********************** 84 2023-11-29 21:11 43 ************************ 85 2023-11-29 21:12 43 ************************ 86 2023-11-29 21:13 43 ************************ 87 2023-11-29 21:14 41 ********************** ... ..( 2 skipped). .. ********************** 90 2023-11-29 21:17 41 ********************** 91 2023-11-29 21:18 43 ************************ ... ..( 4 skipped). .. ************************ 96 2023-11-29 21:23 43 ************************ 97 2023-11-29 21:24 41 ********************** 98 2023-11-29 21:25 41 ********************** 99 2023-11-29 21:26 43 ************************ ... ..( 3 skipped). .. ************************ 103 2023-11-29 21:30 43 ************************ 104 2023-11-29 21:31 41 ********************** 105 2023-11-29 21:32 43 ************************ 106 2023-11-29 21:33 41 ********************** 107 2023-11-29 21:34 43 ************************ 108 2023-11-29 21:35 41 ********************** 109 2023-11-29 21:36 43 ************************ ... ..( 4 skipped). .. ************************ 114 2023-11-29 21:41 43 ************************ SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1866 --- Lifetime Power-On Resets 0x01 0x010 4 11609 --- Power-on Hours 0x01 0x018 6 328205240 --- Logical Sectors Written 0x01 0x020 6 608223882 --- Number of Write Commands 0x01 0x028 6 2823592348 --- Logical Sectors Read 0x01 0x030 6 149495452 --- Number of Read Commands 0x01 0x038 6 4294967296 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 31 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 43 --- Current Temperature 0x05 0x010 1 41 --- Average Short Term Temperature 0x05 0x018 1 41 --- Average Long Term Temperature 0x05 0x020 1 60 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 48 --- Highest Average Short Term Temperature 0x05 0x038 1 0 --- Lowest Average Short Term Temperature 0x05 0x040 1 42 --- Highest Average Long Term Temperature 0x05 0x048 1 0 --- Lowest Average Long Term Temperature 0x05 0x050 4 46 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 16683 --- Number of Hardware Resets 0x06 0x010 4 9662 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 20 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 26 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.6.2-101.fc38.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron Client SSDs Device Model: CT250MX500SSD1 Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: M3CR022 User Capacity: 250,059,350,016 bytes [250 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Nov 29 21:41:02 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 0 5 Reallocate_NAND_Blk_Cnt -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 18876 12 Power_Cycle_Count -O--CK 100 100 000 - 1867 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Ave_Block-Erase_Count -O--CK 099 099 000 - 19 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 34 180 Unused_Reserve_NAND_Blk PO--CK 000 000 000 - 27 183 SATA_Interfac_Downshift -O--CK 100 100 000 - 0 184 Error_Correction_Count -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 062 052 000 - 38 (Min/Max 0/48) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_ECC_Cnt -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 202 Percent_Lifetime_Remain ----CK 099 099 001 - 1 206 Write_Error_Rate -OSR-- 100 100 000 - 0 210 Success_RAIN_Recov_Cnt -O--CK 100 100 000 - 0 246 Total_LBAs_Written -O--CK 100 100 000 - 2429674734 247 Host_Program_Page_Count -O--CK 100 100 000 - 41516414 248 FTL_Program_Page_Count -O--CK 100 100 000 - 70135979 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 64 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Completed [00% left] (0-65535) Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 21/41 Celsius Lifetime Min/Max Temperature: 0/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: 0/100 Celsius Temperature History Size (Index): 128 (64) Index Estimated Time Temperature Celsius 65 2023-11-29 19:34 35 **************** 66 2023-11-29 19:35 35 **************** 67 2023-11-29 19:36 36 ***************** 68 2023-11-29 19:37 36 ***************** 69 2023-11-29 19:38 35 **************** 70 2023-11-29 19:39 36 ***************** 71 2023-11-29 19:40 36 ***************** 72 2023-11-29 19:41 36 ***************** 73 2023-11-29 19:42 35 **************** ... ..( 2 skipped). .. **************** 76 2023-11-29 19:45 35 **************** 77 2023-11-29 19:46 40 ********************* 78 2023-11-29 19:47 41 ********************** 79 2023-11-29 19:48 36 ***************** 80 2023-11-29 19:49 36 ***************** 81 2023-11-29 19:50 36 ***************** 82 2023-11-29 19:51 40 ********************* 83 2023-11-29 19:52 35 **************** ... ..( 9 skipped). .. **************** 93 2023-11-29 20:02 35 **************** 94 2023-11-29 20:03 36 ***************** 95 2023-11-29 20:04 35 **************** ... ..( 5 skipped). .. **************** 101 2023-11-29 20:10 35 **************** 102 2023-11-29 20:11 36 ***************** 103 2023-11-29 20:12 35 **************** ... ..( 10 skipped). .. **************** 114 2023-11-29 20:23 35 **************** 115 2023-11-29 20:24 36 ***************** 116 2023-11-29 20:25 35 **************** ... ..( 15 skipped). .. **************** 4 2023-11-29 20:41 35 **************** 5 2023-11-29 20:42 36 ***************** 6 2023-11-29 20:43 35 **************** ... ..( 57 skipped). .. **************** 64 2023-11-29 21:41 35 **************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1867 --- Lifetime Power-On Resets 0x01 0x010 4 18876 --- Power-on Hours 0x01 0x018 6 2429674734 --- Logical Sectors Written 0x01 0x020 6 18182262 --- Number of Write Commands 0x01 0x028 6 3240297422 --- Logical Sectors Read 0x01 0x030 6 125093811 --- Number of Read Commands 0x01 0x038 6 4294967296 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 34 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 38 --- Current Temperature 0x05 0x010 1 35 --- Average Short Term Temperature 0x05 0x018 1 35 --- Average Long Term Temperature 0x05 0x020 1 48 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 42 --- Highest Average Short Term Temperature 0x05 0x038 1 0 --- Lowest Average Short Term Temperature 0x05 0x040 1 42 --- Highest Average Long Term Temperature 0x05 0x048 1 0 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 16899 --- Number of Hardware Resets 0x06 0x010 4 9736 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 26 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.6.2-101.fc38.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Desktop SSHD Device Model: ST1000DX001-1NS162 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC41 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Nov 29 21:41:02 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 104) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1081) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 119 099 006 - 227182304 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3271 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 087 060 030 - 643193044 9 Power_On_Hours -O--CK 069 069 000 - 27623 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 097 097 020 - 3277 183 Runtime_Bad_Block -O--CK 037 037 000 - 63 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 097 097 000 - 3 188 Command_Timeout -O--CK 100 099 000 - 0 0 55 189 High_Fly_Writes -O-RCK 096 096 000 - 4 190 Airflow_Temperature_Cel -O---K 066 058 045 - 34 (Min/Max 21/35) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 13 193 Load_Cycle_Count -O--CK 001 001 000 - 230972 194 Temperature_Celsius -O---K 034 042 000 - 34 (0 16 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 26523h+09m+38.698s 241 Total_LBAs_Written ------ 100 253 000 - 97004597672 242 Total_LBAs_Read ------ 100 253 000 - 1543831368813 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 3900 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 4580 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 3 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3 [2] occurred at disk power-on lifetime: 26541 hours (1105 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 30 b1 da 30 00 00 Error: UNC at LBA = 0x30b1da30 = 816962096 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 00 00 38 16 80 40 00 00:00:50.628 READ FPDMA QUEUED 60 00 00 02 00 00 00 05 99 1a 98 40 00 00:00:50.616 READ FPDMA QUEUED 60 00 00 00 20 00 00 00 24 a9 00 40 00 00:00:50.615 READ FPDMA QUEUED 60 00 00 02 00 00 00 30 bb 44 f0 40 00 00:00:50.602 READ FPDMA QUEUED 60 00 00 02 00 00 00 07 ad 80 00 40 00 00:00:50.593 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 25807 hours (1075 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 00 1f 48 00 00 00 Error: UNC at LBA = 0x001f4800 = 2050048 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 72 70 68 00 40 00 00:00:40.552 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 1f 48 00 40 00 00:00:40.114 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 00 08 00 40 00 00:00:40.114 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 00 00 00 40 00 00:00:40.114 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 1f 48 80 40 00 00:00:34.874 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 24175 hours (1007 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 3c b4 8e 98 00 00 Error: UNC at LBA = 0x3cb48e98 = 1018465944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 98 00 00 3c b4 a2 b0 40 00 00:00:48.518 READ FPDMA QUEUED 60 00 00 00 10 00 00 3c b4 a2 90 40 00 00:00:48.518 READ FPDMA QUEUED 60 00 00 01 d0 00 00 3c b4 a0 b0 40 00 00:00:48.518 READ FPDMA QUEUED 60 00 00 01 c0 00 00 3c b4 9e c0 40 00 00:00:48.518 READ FPDMA QUEUED 60 00 00 04 d0 00 00 3c b4 99 e0 40 00 00:00:48.518 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 25/34 Celsius Lifetime Min/Max Temperature: 25/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 3277 --- Lifetime Power-On Resets 0x01 0x010 4 27623 --- Power-on Hours 0x01 0x018 6 96545242184 --- Logical Sectors Written 0x01 0x020 6 1114739667 --- Number of Write Commands 0x01 0x028 6 87699241885 --- Logical Sectors Read 0x01 0x030 6 572228428 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 27602 --- Spindle Motor Power-on Hours 0x03 0x010 4 9716 --- Head Flying Hours 0x03 0x018 4 230972 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 1 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 55 --- Resets Between Cmd Acceptance and Completion |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 16 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdd smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.6.2-101.fc38.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3250410AS Serial Number: -- Firmware Version: 3.AAC User Capacity: 250,058,268,160 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5528 ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Wed Nov 29 21:41:03 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 64) minutes. SCT capabilities: (0x0001) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 078 070 006 - 151247985 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 092 092 020 - 8284 5 Reallocated_Sector_Ct PO--CK 098 098 036 - 86 7 Seek_Error_Rate POSR-- 089 060 030 - 845014906 9 Power_On_Hours -O--CK 040 040 000 - 53022 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 092 092 020 - 8284 187 Reported_Uncorrect -O--CK 001 001 000 - 214 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 045 045 Past 37 (Min/Max 22/39) 194 Temperature_Celsius -O---K 037 055 000 - 37 (0 15 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 056 045 000 - 133216843 197 Current_Pending_Sector -O--C- 100 100 000 - 2 198 Offline_Uncorrectable ----C- 100 100 000 - 2 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 245 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 245 [4] occurred at disk power-on lifetime: 22648 hours (943 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 07 3f 00 61 58 e7 00 Error: UNC at LBA = 0x73f006158 = 31121760600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 07 3f 00 61 57 e7 00 08:06:22.340 READ DMA c8 00 00 00 08 00 07 3f 00 61 4f e7 00 08:06:22.339 READ DMA c8 00 00 00 08 00 07 3f 00 61 47 e7 00 08:06:22.339 READ DMA c8 00 00 00 08 00 07 3f 00 61 3f e7 00 08:06:22.339 READ DMA c8 00 00 00 08 00 07 3f 00 61 37 e7 00 08:06:22.338 READ DMA Error 244 [3] occurred at disk power-on lifetime: 22648 hours (943 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 07 3f 00 61 58 e7 00 Error: UNC at LBA = 0x73f006158 = 31121760600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 07 3f 00 61 57 e7 00 08:07:05.962 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 08:07:05.962 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 01 00 00 ff ff 00 ff ff a0 00 08:07:05.962 IDENTIFY DEVICE ef 00 03 00 46 00 ff ff 00 ff ff a0 00 08:07:05.961 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 08:07:01.952 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 243 [2] occurred at disk power-on lifetime: 22648 hours (943 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 07 3f 00 61 58 e7 00 Error: UNC at LBA = 0x73f006158 = 31121760600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 07 3f 00 61 57 e7 00 08:06:46.001 READ DMA c8 00 00 00 38 00 07 71 00 37 bf e7 00 08:06:46.000 READ DMA c8 00 00 00 20 00 07 71 00 37 9f e7 00 08:06:35.929 READ DMA b0 00 d0 00 01 00 02 17 00 fd 0f 00 00 08:06:35.929 SMART READ DATA b0 00 d8 01 00 00 02 17 00 fd 0f 00 00 08:07:01.952 SMART ENABLE OPERATIONS Error 242 [1] occurred at disk power-on lifetime: 22648 hours (943 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 07 3f 00 61 58 e7 00 Error: UNC at LBA = 0x73f006158 = 31121760600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 07 3f 00 61 57 e7 00 08:06:22.340 READ DMA ec 00 00 01 00 00 ff ff 00 ff ff 00 00 08:06:22.339 IDENTIFY DEVICE 27 00 00 00 00 00 00 00 00 00 00 e0 00 08:06:22.339 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 01 00 00 ff ff 00 ff ff a0 00 08:06:22.339 IDENTIFY DEVICE ef 00 03 00 46 00 ff ff 00 ff ff a0 00 08:06:22.338 SET FEATURES [Set transfer mode] Error 241 [0] occurred at disk power-on lifetime: 22648 hours (943 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 07 3f 00 61 58 e7 00 Error: UNC at LBA = 0x73f006158 = 31121760600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 07 3f 00 61 57 e7 00 08:06:22.340 READ DMA c8 00 00 00 08 00 07 3f 00 61 4f e7 00 08:06:22.339 READ DMA c8 00 00 00 08 00 07 3f 00 61 47 e7 00 08:06:22.339 READ DMA c8 00 00 00 08 00 07 3f 00 61 3f e7 00 08:06:22.339 READ DMA c8 00 00 00 08 00 07 3f 00 61 37 e7 00 08:06:22.338 READ DMA Error 240 [19] occurred at disk power-on lifetime: 22648 hours (943 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 07 3f 00 61 58 e7 00 Error: UNC at LBA = 0x73f006158 = 31121760600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 07 3f 00 61 57 e7 00 08:07:05.962 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 08:07:05.962 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 01 00 00 ff ff 00 ff ff a0 00 08:07:05.962 IDENTIFY DEVICE ef 00 03 00 46 00 ff ff 00 ff ff a0 00 08:07:05.961 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 08:07:01.952 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 239 [18] occurred at disk power-on lifetime: 22648 hours (943 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 07 3f 00 61 58 e7 00 Error: UNC at LBA = 0x73f006158 = 31121760600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 07 3f 00 61 57 e7 00 08:06:46.001 READ DMA c8 00 00 00 38 00 07 71 00 37 bf e7 00 08:06:46.000 READ DMA c8 00 00 00 20 00 07 71 00 37 9f e7 00 08:06:35.929 READ DMA b0 00 d0 00 01 00 02 17 00 fd 0f 00 00 08:06:35.929 SMART READ DATA b0 00 d8 01 00 00 02 17 00 fd 0f 00 00 08:07:01.952 SMART ENABLE OPERATIONS Error 238 [17] occurred at disk power-on lifetime: 22648 hours (943 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 07 3f 00 61 58 e7 00 Error: UNC at LBA = 0x73f006158 = 31121760600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 07 3f 00 61 57 e7 00 08:06:22.340 READ DMA ec 00 00 01 00 00 ff ff 00 ff ff 00 00 08:06:22.339 IDENTIFY DEVICE 27 00 00 00 00 00 00 00 00 00 00 e0 00 08:06:22.339 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 01 00 00 ff ff 00 ff ff a0 00 08:06:22.339 IDENTIFY DEVICE ef 00 03 00 46 00 ff ff 00 ff ff a0 00 08:06:22.338 SET FEATURES [Set transfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 9801 - # 2 Short offline Completed: read failure 80% 7187 214873610606 # 3 Extended offline Completed without error 00% 400 - # 4 Extended offline Interrupted (host reset) 60% 398 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 521 (0x0209) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: --/ 0 Celsius Lifetime Min/Max Temperature: --/ 0 Celsius SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 14 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 18 Transition from drive PhyRdy to drive PhyNRdy 0x8002 2 0 Vendor specific 0x8003 2 2 Vendor specific 0x8004 2 0 Vendor specific