/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.9 Device Model: ST3160811AS Serial Number: -- Firmware Version: 3.AAE User Capacity: 160 040 803 840 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sun Jun 5 09:17:29 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 54) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 083 006 - 145151438 3 Spin_Up_Time PO---- 095 095 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 4023 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 084 060 030 - 9085808389 9 Power_On_Hours -O--CK 091 091 000 - 7912 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4723 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 098 098 000 - 2 190 Airflow_Temperature_Cel -O---K 070 041 045 Past 30 (Min/Max 25/30) 194 Temperature_Celsius -O---K 030 059 000 - 30 (0 17 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 060 045 000 - 34570138 197 Current_Pending_Sector -O--C- 100 100 000 - 1 198 Offline_Uncorrectable ----C- 100 100 000 - 1 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 74 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 099 252 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 508 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 508 [7] occurred at disk power-on lifetime: 6306 hours (262 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 02:42:04.567 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 00 00 12 96 00 a1 6e e0 00 02:42:04.507 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 00 00 00 12 96 00 a1 6e e2 00 02:42:04.283 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 01 01 00 12 96 00 a1 6e e0 00 02:42:04.210 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 02:42:02.130 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 507 [6] occurred at disk power-on lifetime: 6306 hours (262 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 02:41:59.076 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 00 00 12 96 00 a1 6e e0 00 02:41:59.076 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 00 00 00 12 96 00 a1 6e e2 00 02:41:59.076 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 01 00 12 9e 00 a1 af e0 00 02:41:59.075 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 29 00 00 00 01 00 12 9e 00 a1 af e0 00 02:42:02.130 READ MULTIPLE EXT Error 506 [5] occurred at disk power-on lifetime: 6306 hours (262 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 02:03:27.060 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 00 00 12 96 00 a1 6e e0 00 02:03:26.835 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 00 00 00 12 96 00 a1 6e e2 00 02:03:26.768 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 01 01 00 12 96 00 a1 6e e0 00 02:03:26.593 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 02:03:26.468 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 505 [4] occurred at disk power-on lifetime: 6306 hours (262 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 02:03:27.060 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 00 00 12 96 00 a1 6e e0 00 02:03:26.835 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 00 00 00 12 96 00 a1 6e e2 00 02:03:26.768 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 01 00 12 9e 00 a1 af e0 00 02:03:26.593 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 29 00 00 00 01 00 12 9e 00 a1 af e0 00 02:03:26.468 READ MULTIPLE EXT Error 504 [3] occurred at disk power-on lifetime: 6305 hours (262 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 01:21:25.261 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 00 00 12 96 00 a1 6e e0 00 01:21:25.144 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 00 00 00 12 96 00 a1 6e e2 00 01:21:25.074 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 01 01 00 12 96 00 a1 6e e0 00 01:21:22.765 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 01:21:22.732 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 503 [2] occurred at disk power-on lifetime: 6305 hours (262 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 01:21:25.261 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 00 00 12 96 00 a1 6e e0 00 01:21:25.144 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 00 00 00 12 96 00 a1 6e e2 00 01:21:25.074 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 01 00 12 9e 00 a1 af e0 00 01:21:22.765 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 29 00 00 00 01 00 12 9e 00 a1 af e0 00 01:21:22.732 READ MULTIPLE EXT Error 502 [1] occurred at disk power-on lifetime: 6304 hours (262 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 00:39:47.455 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 00 00 12 96 00 a1 6e e0 00 00:39:47.231 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 00 00 00 12 96 00 a1 6e e2 00 00:39:47.164 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 01 01 00 12 96 00 a1 6e e0 00 00:39:46.989 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 00:39:46.872 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 501 [0] occurred at disk power-on lifetime: 6304 hours (262 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e2 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 ff 01 01 00 12 96 00 a1 6e e2 00 00:39:47.455 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 00 00 12 96 00 a1 6e e0 00 00:39:47.231 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 ff 00 00 00 12 96 00 a1 6e e2 00 00:39:47.164 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 ff 00 01 00 12 9e 00 a1 af e0 00 00:39:46.989 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 29 00 00 00 01 00 12 9e 00 a1 af e0 00 00:39:46.872 READ MULTIPLE EXT SMART Extended Self-test Log Version: 1 (1 sectors) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD6400AARS-00Y5B1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 640 133 946 880 bytes [640 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jun 5 09:17:29 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 154) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 122 118 021 - 6858 4 Start_Stop_Count -O--CK 099 099 000 - 1147 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 086 086 000 - 10864 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1091 192 Power-Off_Retract_Count -O--CK 200 200 000 - 318 193 Load_Cycle_Count -O--CK 131 131 000 - 209961 194 Temperature_Celsius -O---K 121 102 000 - 26 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 382 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 25/26 Celsius Lifetime Min/Max Temperature: 25/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (321) Index Estimated Time Temperature Celsius 322 2016-06-05 01:20 31 ************ ... ..( 11 skipped). .. ************ 334 2016-06-05 01:32 31 ************ 335 2016-06-05 01:33 ? - 336 2016-06-05 01:34 24 ***** 337 2016-06-05 01:35 24 ***** 338 2016-06-05 01:36 25 ****** 339 2016-06-05 01:37 25 ****** 340 2016-06-05 01:38 26 ******* 341 2016-06-05 01:39 26 ******* 342 2016-06-05 01:40 26 ******* 343 2016-06-05 01:41 27 ******** 344 2016-06-05 01:42 28 ********* 345 2016-06-05 01:43 28 ********* 346 2016-06-05 01:44 29 ********** ... ..( 3 skipped). .. ********** 350 2016-06-05 01:48 29 ********** 351 2016-06-05 01:49 30 *********** ... ..( 8 skipped). .. *********** 360 2016-06-05 01:58 30 *********** 361 2016-06-05 01:59 31 ************ ... ..( 91 skipped). .. ************ 453 2016-06-05 03:31 31 ************ 454 2016-06-05 03:32 32 ************* 455 2016-06-05 03:33 31 ************ ... ..( 20 skipped). .. ************ 476 2016-06-05 03:54 31 ************ 477 2016-06-05 03:55 ? - 0 2016-06-05 03:56 24 ***** 1 2016-06-05 03:57 25 ****** 2 2016-06-05 03:58 25 ****** 3 2016-06-05 03:59 26 ******* ... ..( 2 skipped). .. ******* 6 2016-06-05 04:02 26 ******* 7 2016-06-05 04:03 27 ******** 8 2016-06-05 04:04 27 ******** 9 2016-06-05 04:05 28 ********* 10 2016-06-05 04:06 29 ********** ... ..( 3 skipped). .. ********** 14 2016-06-05 04:10 29 ********** 15 2016-06-05 04:11 30 *********** ... ..( 19 skipped). .. *********** 35 2016-06-05 04:31 30 *********** 36 2016-06-05 04:32 31 ************ ... ..( 7 skipped). .. ************ 44 2016-06-05 04:40 31 ************ 45 2016-06-05 04:41 30 *********** 46 2016-06-05 04:42 31 ************ ... ..( 27 skipped). .. ************ 74 2016-06-05 05:10 31 ************ 75 2016-06-05 05:11 32 ************* ... ..( 87 skipped). .. ************* 163 2016-06-05 06:39 32 ************* 164 2016-06-05 06:40 31 ************ ... ..( 31 skipped). .. ************ 196 2016-06-05 07:12 31 ************ 197 2016-06-05 07:13 30 *********** ... ..( 13 skipped). .. *********** 211 2016-06-05 07:27 30 *********** 212 2016-06-05 07:28 31 ************ ... ..( 11 skipped). .. ************ 224 2016-06-05 07:40 31 ************ 225 2016-06-05 07:41 32 ************* ... ..( 2 skipped). .. ************* 228 2016-06-05 07:44 32 ************* 229 2016-06-05 07:45 31 ************ 230 2016-06-05 07:46 31 ************ 231 2016-06-05 07:47 31 ************ 232 2016-06-05 07:48 30 *********** ... ..( 15 skipped). .. *********** 248 2016-06-05 08:04 30 *********** 249 2016-06-05 08:05 29 ********** ... ..( 32 skipped). .. ********** 282 2016-06-05 08:38 29 ********** 283 2016-06-05 08:39 ? - 284 2016-06-05 08:40 25 ****** ... ..( 3 skipped). .. ****** 288 2016-06-05 08:44 25 ****** 289 2016-06-05 08:45 26 ******* ... ..( 3 skipped). .. ******* 293 2016-06-05 08:49 26 ******* 294 2016-06-05 08:50 31 ************ 295 2016-06-05 08:51 31 ************ 296 2016-06-05 08:52 30 *********** ... ..( 7 skipped). .. *********** 304 2016-06-05 09:00 30 *********** 305 2016-06-05 09:01 31 ************ ... ..( 15 skipped). .. ************ 321 2016-06-05 09:17 31 ************ SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 581 Vendor specific