/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.79-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Constellation ES.3 Device Model: ST2000NM0033-9ZM175 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: SN04 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Dec 18 18:11:10 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 592) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 241) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x50bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 081 063 044 - 142893961 3 Spin_Up_Time PO---- 095 095 000 - 0 4 Start_Stop_Count -O--CK 096 096 020 - 4202 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 092 060 030 - 1675484581 9 Power_On_Hours -O--CK 093 093 000 - 6828 10 Spin_Retry_Count PO--C- 100 099 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4277 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 095 000 - 98786541607 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 059 051 045 - 41 (Min/Max 38/41) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 1312 193 Load_Cycle_Count -O--CK 098 098 000 - 4333 194 Temperature_Celsius -O---K 041 049 000 - 41 (0 9 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 021 010 000 - 142893961 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 001 000 - 14753 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL,SL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbd GPL VS 512 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc2 GPL,SL VS 50 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xd1 GPL,SL VS 8 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 6816 - # 2 Extended offline Interrupted (host reset) 00% 5938 - # 3 Extended offline Interrupted (host reset) 00% 5934 - # 4 Extended offline Interrupted (host reset) 00% 5923 - # 5 Extended offline Interrupted (host reset) 00% 5914 - # 6 Extended offline Interrupted (host reset) 00% 5910 - # 7 Extended offline Interrupted (host reset) 00% 5897 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 37/41 Celsius Lifetime Min/Max Temperature: 9/49 Celsius Under/Over Temperature Limit Count: 0/15 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (46) Index Estimated Time Temperature Celsius 47 2022-12-17 21:00 ? - 48 2022-12-17 21:10 27 ******** 49 2022-12-17 21:20 ? - 50 2022-12-17 21:30 27 ******** 51 2022-12-17 21:40 ? - 52 2022-12-17 21:50 27 ******** 53 2022-12-17 22:00 ? - 54 2022-12-17 22:10 27 ******** 55 2022-12-17 22:20 ? - 56 2022-12-17 22:30 29 ********** 57 2022-12-17 22:40 ? - 58 2022-12-17 22:50 30 *********** 59 2022-12-17 23:00 ? - 60 2022-12-17 23:10 30 *********** 61 2022-12-17 23:20 ? - 62 2022-12-17 23:30 31 ************ 63 2022-12-17 23:40 34 *************** 64 2022-12-17 23:50 40 ********************* 65 2022-12-18 00:00 43 ************************ 66 2022-12-18 00:10 ? - 67 2022-12-18 00:20 46 *************************** 68 2022-12-18 00:30 45 ************************** 69 2022-12-18 00:40 45 ************************** 70 2022-12-18 00:50 44 ************************* ... ..( 5 skipped). .. ************************* 76 2022-12-18 01:50 44 ************************* 77 2022-12-18 02:00 43 ************************ ... ..( 10 skipped). .. ************************ 88 2022-12-18 03:50 43 ************************ 89 2022-12-18 04:00 42 *********************** ... ..( 9 skipped). .. *********************** 99 2022-12-18 05:40 42 *********************** 100 2022-12-18 05:50 41 ********************** ... ..( 3 skipped). .. ********************** 104 2022-12-18 06:30 41 ********************** 105 2022-12-18 06:40 42 *********************** 106 2022-12-18 06:50 42 *********************** 107 2022-12-18 07:00 42 *********************** 108 2022-12-18 07:10 41 ********************** ... ..( 12 skipped). .. ********************** 121 2022-12-18 09:20 41 ********************** 122 2022-12-18 09:30 ? - 123 2022-12-18 09:40 41 ********************** ... ..( 2 skipped). .. ********************** 126 2022-12-18 10:10 41 ********************** 127 2022-12-18 10:20 40 ********************* 0 2022-12-18 10:30 40 ********************* 1 2022-12-18 10:40 40 ********************* 2 2022-12-18 10:50 39 ******************** 3 2022-12-18 11:00 39 ******************** 4 2022-12-18 11:10 40 ********************* ... ..( 5 skipped). .. ********************* 10 2022-12-18 12:10 40 ********************* 11 2022-12-18 12:20 39 ******************** 12 2022-12-18 12:30 39 ******************** 13 2022-12-18 12:40 40 ********************* 14 2022-12-18 12:50 40 ********************* 15 2022-12-18 13:00 41 ********************** ... ..( 3 skipped). .. ********************** 19 2022-12-18 13:40 41 ********************** 20 2022-12-18 13:50 40 ********************* ... ..( 5 skipped). .. ********************* 26 2022-12-18 14:50 40 ********************* 27 2022-12-18 15:00 ? - 28 2022-12-18 15:10 25 ****** 29 2022-12-18 15:20 29 ********** 30 2022-12-18 15:30 34 *************** 31 2022-12-18 15:40 ? - 32 2022-12-18 15:50 37 ****************** 33 2022-12-18 16:00 39 ******************** 34 2022-12-18 16:10 40 ********************* 35 2022-12-18 16:20 41 ********************** 36 2022-12-18 16:30 41 ********************** 37 2022-12-18 16:40 41 ********************** 38 2022-12-18 16:50 40 ********************* ... ..( 7 skipped). .. ********************* 46 2022-12-18 18:10 40 ********************* SCT Error Recovery Control: Read: 100 (10.0 seconds) Write: 100 (10.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 19 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.79-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue EIDE Device Model: WDC WD1600AAJB-00J3A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.03E01 User Capacity: 160,040,803,840 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) Transport Type: Parallel, ATA8-APT Local Time is: Sun Dec 18 18:11:11 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3000) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 39) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 499 3 Spin_Up_Time POS--K 133 125 021 - 4350 4 Start_Stop_Count -O--CK 091 091 000 - 9591 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 064 064 000 - 26717 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 091 091 000 - 9556 192 Power-Off_Retract_Count -O--CK 198 198 000 - 1846 193 Load_Cycle_Count -O--CK 197 197 000 - 9591 194 Temperature_Celsius -O---K 103 090 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 24805 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 24805 [12] occurred at disk power-on lifetime: 23662 hours (985 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 1e 9c 79 ed 00 Error: UNC at LBA = 0x0d1e9c79 = 220109945 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 00 1e 9c 78 ed 00 00:06:00.816 READ DMA c8 00 00 00 88 00 00 00 0d 22 20 ed 00 00:06:00.801 READ DMA c8 00 00 00 08 00 00 00 41 11 d8 e7 00 00:06:00.792 READ DMA c8 00 00 00 08 00 00 00 81 18 08 e6 00 00:06:00.780 READ DMA c8 00 00 00 90 00 00 00 06 64 88 e4 00 00:06:00.766 READ DMA Error 24804 [11] occurred at disk power-on lifetime: 10195 hours (424 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 10 85 00 8e e3 e0 00 Error: UNC 2 sectors at LBA = 0x1085008ee3 = 70950883043 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 02 00 00 10 8e 85 e3 e0 00 03:15:01.265 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:15:01.265 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:15:01.256 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 03:15:01.249 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:15:01.225 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 24803 [10] occurred at disk power-on lifetime: 10195 hours (424 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 10 85 00 8e e3 e0 00 Error: UNC 2 sectors at LBA = 0x1085008ee3 = 70950883043 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 02 00 00 10 8e 85 e3 e0 00 03:14:59.028 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:59.028 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:14:59.019 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 03:14:59.011 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:58.988 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 24802 [9] occurred at disk power-on lifetime: 10195 hours (424 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 10 85 00 8e e3 e0 00 Error: UNC 2 sectors at LBA = 0x1085008ee3 = 70950883043 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 02 00 00 10 8e 85 e3 e0 00 03:14:56.794 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:56.794 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:14:56.785 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 03:14:56.777 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:56.754 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 24801 [8] occurred at disk power-on lifetime: 10195 hours (424 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 10 85 00 8e e3 e0 00 Error: UNC 2 sectors at LBA = 0x1085008ee3 = 70950883043 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 02 00 00 10 8e 85 e3 e0 00 03:14:54.272 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:54.272 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:14:54.263 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 03:14:54.256 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:54.232 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 24800 [7] occurred at disk power-on lifetime: 10195 hours (424 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 10 85 00 8e e3 e0 00 Error: UNC 2 sectors at LBA = 0x1085008ee3 = 70950883043 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 02 00 00 10 8e 85 e3 e0 00 03:14:52.035 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:52.035 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:14:52.026 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 03:14:52.018 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:51.995 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 24799 [6] occurred at disk power-on lifetime: 10195 hours (424 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 10 85 00 8e e3 e0 00 Error: UNC 2 sectors at LBA = 0x1085008ee3 = 70950883043 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 02 00 00 10 8e 85 e3 e0 00 03:14:49.794 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:49.793 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:14:49.784 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 03:14:49.776 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:49.753 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 24798 [5] occurred at disk power-on lifetime: 10195 hours (424 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 10 85 00 8e e3 e0 00 Error: UNC 2 sectors at LBA = 0x1085008ee3 = 70950883043 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 02 00 00 10 8e 85 e3 e0 00 03:14:47.278 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:47.267 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:14:47.258 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 03:14:47.251 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:14:47.227 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 26701 - # 2 Extended offline Completed without error 00% 25799 - # 3 Extended offline Completed without error 00% 25789 - # 4 Extended offline Completed without error 00% 25780 - # 5 Extended offline Completed without error 00% 25775 - # 6 Extended offline Completed: read failure 90% 14645 277775843 # 7 Short offline Completed: read failure 90% 7336 277775843 2 of 2 failed self-tests are outdated by newer successful extended offline self-test # 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 36/40 Celsius Lifetime Min/Max Temperature: 26/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (80) Index Estimated Time Temperature Celsius 81 2022-12-18 16:04 37 ****************** 82 2022-12-18 16:05 38 ******************* ... ..( 8 skipped). .. ******************* 91 2022-12-18 16:14 38 ******************* 92 2022-12-18 16:15 39 ******************** ... ..( 9 skipped). .. ******************** 102 2022-12-18 16:25 39 ******************** 103 2022-12-18 16:26 40 ********************* 104 2022-12-18 16:27 39 ******************** 105 2022-12-18 16:28 40 ********************* 106 2022-12-18 16:29 39 ******************** 107 2022-12-18 16:30 40 ********************* 108 2022-12-18 16:31 39 ******************** 109 2022-12-18 16:32 39 ******************** 110 2022-12-18 16:33 40 ********************* 111 2022-12-18 16:34 40 ********************* 112 2022-12-18 16:35 39 ******************** 113 2022-12-18 16:36 40 ********************* ... ..( 3 skipped). .. ********************* 117 2022-12-18 16:40 40 ********************* 118 2022-12-18 16:41 39 ******************** 119 2022-12-18 16:42 39 ******************** 120 2022-12-18 16:43 40 ********************* 121 2022-12-18 16:44 40 ********************* 122 2022-12-18 16:45 39 ******************** 123 2022-12-18 16:46 40 ********************* 124 2022-12-18 16:47 40 ********************* 125 2022-12-18 16:48 39 ******************** 126 2022-12-18 16:49 40 ********************* 127 2022-12-18 16:50 40 ********************* 0 2022-12-18 16:51 40 ********************* 1 2022-12-18 16:52 39 ******************** ... ..( 2 skipped). .. ******************** 4 2022-12-18 16:55 39 ******************** 5 2022-12-18 16:56 40 ********************* ... ..( 8 skipped). .. ********************* 14 2022-12-18 17:05 40 ********************* 15 2022-12-18 17:06 39 ******************** ... ..( 31 skipped). .. ******************** 47 2022-12-18 17:38 39 ******************** 48 2022-12-18 17:39 40 ********************* 49 2022-12-18 17:40 39 ******************** 50 2022-12-18 17:41 39 ******************** 51 2022-12-18 17:42 40 ********************* 52 2022-12-18 17:43 39 ******************** 53 2022-12-18 17:44 40 ********************* 54 2022-12-18 17:45 39 ******************** 55 2022-12-18 17:46 39 ******************** 56 2022-12-18 17:47 39 ******************** 57 2022-12-18 17:48 40 ********************* ... ..( 4 skipped). .. ********************* 62 2022-12-18 17:53 40 ********************* 63 2022-12-18 17:54 39 ******************** 64 2022-12-18 17:55 40 ********************* 65 2022-12-18 17:56 40 ********************* 66 2022-12-18 17:57 40 ********************* 67 2022-12-18 17:58 39 ******************** ... ..( 9 skipped). .. ******************** 77 2022-12-18 18:08 39 ******************** 78 2022-12-18 18:09 40 ********************* 79 2022-12-18 18:10 40 ********************* 80 2022-12-18 18:11 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x8000 4 8942 Vendor specific