/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Blue Mobile Device Model: WDC WD10JPVX-75JC3T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jun 22 15:59:33 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (17460) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 195) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1084 3 Spin_Up_Time POS--K 181 174 021 - 1950 4 Start_Stop_Count -O--CK 099 099 000 - 1330 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 1 9 Power_On_Hours -O--CK 095 095 000 - 4131 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1174 191 G-Sense_Error_Rate -O--CK 060 060 000 - 40 192 Power-Off_Retract_Count -O--CK 200 200 000 - 288 193 Load_Cycle_Count -O--CK 191 191 000 - 28796 194 Temperature_Celsius -O---K 105 099 000 - 42 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 25 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 240 Head_Flying_Hours -O--CK 095 095 000 - 4051 241 Total_LBAs_Written -O--CK 200 200 000 - 17282476617 242 Total_LBAs_Read -O--CK 200 200 000 - 16522557956 254 Free_Fall_Sensor -O--CK 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 3187 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3187 [18] occurred at disk power-on lifetime: 4131 hours (172 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 10 08 00 40 00 Error: UNC at LBA = 0x00100800 = 1050624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 80 00 00 00 10 08 00 40 08 00:43:08.926 READ FPDMA QUEUED 60 00 08 00 78 00 00 72 79 40 80 40 08 00:43:08.926 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 00 40 08 00:43:08.926 READ LOG EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:43:08.926 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:43:08.926 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 3186 [17] occurred at disk power-on lifetime: 4131 hours (172 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 10 08 00 40 00 Error: UNC at LBA = 0x00100800 = 1050624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 20 00 00 00 10 08 00 40 08 00:43:05.598 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:43:05.598 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:43:05.598 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:43:05.597 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:43:05.597 SET FEATURES [Set transfer mode] Error 3185 [16] occurred at disk power-on lifetime: 4131 hours (172 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 10 08 00 40 00 Error: UNC at LBA = 0x00100800 = 1050624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e8 00 00 00 10 08 00 40 08 00:43:02.292 READ FPDMA QUEUED 60 00 08 00 e0 00 00 00 10 08 00 40 08 00:43:02.292 READ FPDMA QUEUED b0 00 d5 00 01 00 00 00 c2 4f 00 00 08 00:43:02.291 SMART READ LOG ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:43:02.291 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:43:02.291 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 3184 [15] occurred at disk power-on lifetime: 4131 hours (172 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 10 08 00 40 00 Error: UNC at LBA = 0x00100800 = 1050624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 88 00 00 00 10 08 00 40 08 00:42:58.940 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:42:58.940 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:42:58.940 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:42:58.939 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:42:58.939 SET FEATURES [Set transfer mode] Error 3183 [14] occurred at disk power-on lifetime: 4131 hours (172 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 10 08 00 40 00 Error: UNC at LBA = 0x00100800 = 1050624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e8 00 00 00 10 08 00 40 08 00:42:55.603 READ FPDMA QUEUED 60 00 08 00 e0 00 00 00 10 08 00 40 08 00:42:55.603 READ FPDMA QUEUED b0 00 da 00 00 00 00 00 c2 4f 00 00 08 00:42:55.501 SMART RETURN STATUS ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:42:55.500 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:42:55.500 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 3182 [13] occurred at disk power-on lifetime: 4131 hours (172 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 10 08 00 40 00 Error: UNC at LBA = 0x00100800 = 1050624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 88 00 00 00 10 08 00 40 08 00:42:52.105 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:42:52.105 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:42:52.105 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:42:52.105 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:42:52.105 SET FEATURES [Set transfer mode] Error 3181 [12] occurred at disk power-on lifetime: 4131 hours (172 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 10 08 00 40 00 Error: UNC at LBA = 0x00100800 = 1050624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 58 00 00 00 10 08 00 40 08 00:42:48.792 READ FPDMA QUEUED 60 00 08 00 50 00 00 00 10 08 00 40 08 00:42:48.792 READ FPDMA QUEUED b0 00 d1 00 01 00 00 00 c2 4f 01 00 08 00:42:48.788 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:42:48.788 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:42:48.788 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 3180 [11] occurred at disk power-on lifetime: 4131 hours (172 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 10 08 00 40 00 Error: UNC at LBA = 0x00100800 = 1050624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 f0 00 00 00 10 08 00 40 08 00:42:45.481 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:42:45.481 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:42:45.481 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:42:45.481 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:42:45.481 SET FEATURES [Set transfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 4130 1050624 # 2 Extended offline Aborted by host 90% 4130 - # 3 Short offline Completed: read failure 90% 4130 1050628 # 4 Extended offline Completed: read failure 90% 4130 1050624 # 5 Extended offline Completed: read failure 90% 4130 1050628 # 6 Extended offline Completed: read failure 90% 4130 1050624 # 7 Short offline Interrupted (host reset) 80% 2735 - # 8 Short offline Completed without error 00% 604 - # 9 Short offline Completed without error 00% 272 - #10 Short offline Completed without error 00% 188 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 37/41 Celsius Lifetime Min/Max Temperature: 12/48 Celsius Lifetime Average Temperature: 33 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (37) Index Estimated Time Temperature Celsius 38 2016-06-22 13:53 36 ***************** 39 2016-06-22 13:54 37 ****************** 40 2016-06-22 13:55 37 ****************** 41 2016-06-22 13:56 38 ******************* 42 2016-06-22 13:57 38 ******************* 43 2016-06-22 13:58 39 ******************** 44 2016-06-22 13:59 39 ******************** 45 2016-06-22 14:00 39 ******************** 46 2016-06-22 14:01 40 ********************* ... ..( 3 skipped). .. ********************* 50 2016-06-22 14:05 40 ********************* 51 2016-06-22 14:06 41 ********************** ... ..( 2 skipped). .. ********************** 54 2016-06-22 14:09 41 ********************** 55 2016-06-22 14:10 42 *********************** ... ..( 3 skipped). .. *********************** 59 2016-06-22 14:14 42 *********************** 60 2016-06-22 14:15 43 ************************ ... ..( 5 skipped). .. ************************ 66 2016-06-22 14:21 43 ************************ 67 2016-06-22 14:22 44 ************************* ... ..( 14 skipped). .. ************************* 82 2016-06-22 14:37 44 ************************* 83 2016-06-22 14:38 ? - 84 2016-06-22 14:39 27 ******** 85 2016-06-22 14:40 ? - 86 2016-06-22 14:41 29 ********** 87 2016-06-22 14:42 ? - 88 2016-06-22 14:43 29 ********** 89 2016-06-22 14:44 ? - 90 2016-06-22 14:45 30 *********** 91 2016-06-22 14:46 ? - 92 2016-06-22 14:47 31 ************ 93 2016-06-22 14:48 31 ************ 94 2016-06-22 14:49 31 ************ 95 2016-06-22 14:50 32 ************* 96 2016-06-22 14:51 ? - 97 2016-06-22 14:52 35 **************** 98 2016-06-22 14:53 35 **************** 99 2016-06-22 14:54 35 **************** 100 2016-06-22 14:55 36 ***************** 101 2016-06-22 14:56 ? - 102 2016-06-22 14:57 36 ***************** 103 2016-06-22 14:58 36 ***************** 104 2016-06-22 14:59 ? - 105 2016-06-22 15:00 37 ****************** 106 2016-06-22 15:01 37 ****************** 107 2016-06-22 15:02 38 ******************* 108 2016-06-22 15:03 ? - 109 2016-06-22 15:04 38 ******************* 110 2016-06-22 15:05 38 ******************* 111 2016-06-22 15:06 39 ******************** 112 2016-06-22 15:07 39 ******************** 113 2016-06-22 15:08 ? - 114 2016-06-22 15:09 40 ********************* 115 2016-06-22 15:10 40 ********************* 116 2016-06-22 15:11 40 ********************* 117 2016-06-22 15:12 39 ******************** 118 2016-06-22 15:13 ? - 119 2016-06-22 15:14 39 ******************** 120 2016-06-22 15:15 39 ******************** 121 2016-06-22 15:16 40 ********************* 122 2016-06-22 15:17 40 ********************* 123 2016-06-22 15:18 ? - 124 2016-06-22 15:19 40 ********************* 125 2016-06-22 15:20 40 ********************* 126 2016-06-22 15:21 40 ********************* 127 2016-06-22 15:22 41 ********************** ... ..( 16 skipped). .. ********************** 16 2016-06-22 15:39 41 ********************** 17 2016-06-22 15:40 ? - 18 2016-06-22 15:41 41 ********************** 19 2016-06-22 15:42 42 *********************** 20 2016-06-22 15:43 42 *********************** 21 2016-06-22 15:44 42 *********************** 22 2016-06-22 15:45 ? - 23 2016-06-22 15:46 37 ****************** 24 2016-06-22 15:47 37 ****************** 25 2016-06-22 15:48 38 ******************* 26 2016-06-22 15:49 38 ******************* 27 2016-06-22 15:50 41 ********************** 28 2016-06-22 15:51 41 ********************** 29 2016-06-22 15:52 40 ********************* ... ..( 3 skipped). .. ********************* 33 2016-06-22 15:56 40 ********************* 34 2016-06-22 15:57 39 ******************** ... ..( 2 skipped). .. ******************** 37 2016-06-22 16:00 39 ******************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 2595 Vendor specific