/dev/sde smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-56-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Black Device Model: WDC WD7501AAES-60Z2A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 06.01D06 User Capacity: 750,156,374,016 bytes [750 GB] Sector Size: 512 bytes logical/physical Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Dec 4 11:16:33 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13200) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 154) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 170 164 021 - 4500 4 Start_Stop_Count -O--CK 095 095 000 - 5867 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 100 253 051 - 0 9 Power_On_Hours -O--CK 066 066 000 - 25406 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5829 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 001 000 - 666 188 Command_Timeout -O--CK 100 001 000 - 4295033602 190 Airflow_Temperature_Cel -O---K 065 048 040 - 35 (Min/Max 18/35) 192 Power-Off_Retract_Count -O--CK 200 200 000 - 281 193 Load_Cycle_Count -O--CK 199 199 000 - 5585 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 666 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 666 [17] occurred at disk power-on lifetime: 1241 hours (51 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 00 5b e4 98 40 00 Error: UNC at LBA = 0x005be498 = 6022296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 e0 00 50 00 00 2c b5 c3 a0 40 00 01:05:21.857 READ FPDMA QUEUED 60 00 80 00 48 00 00 00 5b e4 68 40 00 01:05:21.857 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:05:21.856 READ LOG EXT 60 00 80 00 40 00 00 00 5b e4 68 40 00 01:05:19.959 READ FPDMA QUEUED 60 00 e0 00 38 00 00 2c b5 c3 a0 40 00 01:05:19.959 READ FPDMA QUEUED Error 665 [16] occurred at disk power-on lifetime: 1241 hours (51 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 00 5b e4 98 40 00 Error: UNC at LBA = 0x005be498 = 6022296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 40 00 00 00 5b e4 68 40 00 01:05:19.959 READ FPDMA QUEUED 60 00 e0 00 38 00 00 2c b5 c3 a0 40 00 01:05:19.959 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:05:19.958 READ LOG EXT 61 00 08 00 30 00 00 00 5f 0f 88 40 00 01:05:18.078 WRITE FPDMA QUEUED 60 00 80 00 28 00 00 00 5b e4 68 40 00 01:05:18.077 READ FPDMA QUEUED Error 664 [15] occurred at disk power-on lifetime: 1241 hours (51 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 00 5b e4 98 40 00 Error: WP at LBA = 0x005be498 = 6022296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 30 00 00 00 5f 0f 88 40 00 01:05:18.078 WRITE FPDMA QUEUED 60 00 80 00 28 00 00 00 5b e4 68 40 00 01:05:18.077 READ FPDMA QUEUED 60 00 e0 00 20 00 00 2c b5 c3 a0 40 00 01:05:18.077 READ FPDMA QUEUED 61 00 08 00 18 00 00 00 5f 0f 90 40 00 01:05:18.077 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:05:18.076 READ LOG EXT Error 663 [14] occurred at disk power-on lifetime: 1241 hours (51 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 00 5b e4 98 40 00 Error: UNC at LBA = 0x005be498 = 6022296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 00 5b e4 68 40 00 01:05:16.196 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:05:16.195 READ LOG EXT 60 00 80 00 f8 00 00 00 5b e4 68 40 00 01:05:14.314 READ FPDMA QUEUED 61 01 00 00 f0 00 00 2c b5 c2 a0 40 00 01:05:14.314 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:05:14.314 READ LOG EXT Error 662 [13] occurred at disk power-on lifetime: 1241 hours (51 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 00 5b e4 98 40 00 Error: UNC at LBA = 0x005be498 = 6022296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 f8 00 00 00 5b e4 68 40 00 01:05:14.314 READ FPDMA QUEUED 61 01 00 00 f0 00 00 2c b5 c2 a0 40 00 01:05:14.314 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 01:05:14.314 READ LOG EXT 61 01 00 00 e8 00 00 2c b5 c2 a0 40 00 01:05:12.421 WRITE FPDMA QUEUED 61 01 00 00 e0 00 00 2c b5 c1 a0 40 00 01:05:12.421 WRITE FPDMA QUEUED Error 661 [12] occurred at disk power-on lifetime: 1241 hours (51 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 00 5b e4 98 40 00 Error: WP at LBA = 0x005be498 = 6022296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 e8 00 00 2c b5 c2 a0 40 00 01:05:12.421 WRITE FPDMA QUEUED 61 01 00 00 e0 00 00 2c b5 c1 a0 40 00 01:05:12.421 WRITE FPDMA QUEUED 61 01 00 00 d8 00 00 2c b5 c0 a0 40 00 01:05:12.420 WRITE FPDMA QUEUED 61 01 00 00 d0 00 00 2c b5 bf a0 40 00 01:05:12.419 WRITE FPDMA QUEUED 61 01 00 00 c8 00 00 2c b5 be a0 40 00 01:05:12.419 WRITE FPDMA QUEUED Error 660 [11] occurred at disk power-on lifetime: 1241 hours (51 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 00 5b e4 98 40 00 Error: WP at LBA = 0x005be498 = 6022296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 80 00 00 00 63 a1 d8 40 00 01:05:10.530 WRITE FPDMA QUEUED 61 01 00 00 78 00 00 1f 80 4b 20 40 00 01:05:10.529 WRITE FPDMA QUEUED 61 01 00 00 70 00 00 1f 80 4a 20 40 00 01:05:10.528 WRITE FPDMA QUEUED 61 01 00 00 68 00 00 1f 80 49 20 40 00 01:05:10.528 WRITE FPDMA QUEUED 61 01 00 00 60 00 00 1f 80 48 20 40 00 01:05:10.527 WRITE FPDMA QUEUED Error 659 [10] occurred at disk power-on lifetime: 1241 hours (51 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 00 5b e4 98 40 00 Error: UNC at LBA = 0x005be498 = 6022296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 d8 00 00 00 5b e4 68 40 00 01:05:08.596 READ FPDMA QUEUED 60 01 00 00 d0 00 00 2c b5 bb a0 40 00 01:05:08.596 READ FPDMA QUEUED 60 01 00 00 c8 00 00 2c b5 bc a0 40 00 01:05:08.596 READ FPDMA QUEUED 60 01 00 00 c0 00 00 2c b5 bd a0 40 00 01:05:08.596 READ FPDMA QUEUED 60 01 00 00 b8 00 00 2c b5 be a0 40 00 01:05:08.596 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 14801 - # 2 Short offline Completed without error 00% 13957 - # 3 Short offline Completed without error 00% 13906 - # 4 Short offline Completed without error 00% 13896 - # 5 Short offline Completed without error 00% 13874 - # 6 Short offline Completed without error 00% 1145 - # 7 Short offline Completed without error 00% 1099 - # 8 Short offline Completed without error 00% 923 - # 9 Short offline Completed without error 00% 923 - #10 Short offline Completed without error 00% 534 - #11 Short offline Completed without error 00% 481 - #12 Short offline Completed without error 00% 470 - #13 Short offline Completed without error 00% 450 - #14 Short offline Completed without error 00% 297 - #15 Extended offline Interrupted (host reset) 90% 1 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 19/35 Celsius Lifetime Min/Max Temperature: ?/53 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (9) Index Estimated Time Temperature Celsius 10 2020-12-04 09:09 22 *** 11 2020-12-04 09:10 22 *** 12 2020-12-04 09:11 23 **** 13 2020-12-04 09:12 24 ***** 14 2020-12-04 09:13 25 ****** 15 2020-12-04 09:14 25 ****** 16 2020-12-04 09:15 25 ****** 17 2020-12-04 09:16 26 ******* 18 2020-12-04 09:17 26 ******* 19 2020-12-04 09:18 26 ******* 20 2020-12-04 09:19 27 ******** 21 2020-12-04 09:20 27 ******** 22 2020-12-04 09:21 27 ******** 23 2020-12-04 09:22 28 ********* 24 2020-12-04 09:23 28 ********* 25 2020-12-04 09:24 28 ********* 26 2020-12-04 09:25 29 ********** ... ..( 2 skipped). .. ********** 29 2020-12-04 09:28 29 ********** 30 2020-12-04 09:29 30 *********** 31 2020-12-04 09:30 30 *********** 32 2020-12-04 09:31 31 ************ 33 2020-12-04 09:32 31 ************ 34 2020-12-04 09:33 31 ************ 35 2020-12-04 09:34 32 ************* ... ..( 5 skipped). .. ************* 41 2020-12-04 09:40 32 ************* 42 2020-12-04 09:41 33 ************** ... ..( 5 skipped). .. ************** 48 2020-12-04 09:47 33 ************** 49 2020-12-04 09:48 34 *************** ... ..( 5 skipped). .. *************** 55 2020-12-04 09:54 34 *************** 56 2020-12-04 09:55 35 **************** 57 2020-12-04 09:56 34 *************** 58 2020-12-04 09:57 34 *************** 59 2020-12-04 09:58 35 **************** ... ..( 77 skipped). .. **************** 9 2020-12-04 11:16 35 **************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 7999 Vendor specific /dev/sdf smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-56-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD10EARS-00MVWB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 51.0AB51 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Dec 4 11:16:33 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (25200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 245) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 253 169 021 - 1166 4 Start_Stop_Count -O--CK 096 096 000 - 4914 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 067 067 000 - 24578 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4772 192 Power-Off_Retract_Count -O--CK 200 200 000 - 88 193 Load_Cycle_Count -O--CK 001 001 000 - 1437137 194 Temperature_Celsius -O---K 118 102 000 - 32 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 13632 - # 2 Short offline Completed without error 00% 12772 - # 3 Short offline Completed without error 00% 12720 - # 4 Short offline Completed without error 00% 12710 - # 5 Short offline Completed without error 00% 12688 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 18/32 Celsius Lifetime Min/Max Temperature: 18/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (180) Index Estimated Time Temperature Celsius 181 2020-12-04 03:19 29 ********** 182 2020-12-04 03:20 30 *********** ... ..( 7 skipped). .. *********** 190 2020-12-04 03:28 30 *********** 191 2020-12-04 03:29 ? - 192 2020-12-04 03:30 18 - 193 2020-12-04 03:31 18 - 194 2020-12-04 03:32 18 - 195 2020-12-04 03:33 19 - 196 2020-12-04 03:34 20 * 197 2020-12-04 03:35 21 ** 198 2020-12-04 03:36 21 ** 199 2020-12-04 03:37 22 *** 200 2020-12-04 03:38 22 *** 201 2020-12-04 03:39 22 *** 202 2020-12-04 03:40 23 **** ... ..( 2 skipped). .. **** 205 2020-12-04 03:43 23 **** 206 2020-12-04 03:44 24 ***** 207 2020-12-04 03:45 24 ***** 208 2020-12-04 03:46 25 ****** ... ..( 2 skipped). .. ****** 211 2020-12-04 03:49 25 ****** 212 2020-12-04 03:50 26 ******* ... ..( 4 skipped). .. ******* 217 2020-12-04 03:55 26 ******* 218 2020-12-04 03:56 27 ******** 219 2020-12-04 03:57 26 ******* 220 2020-12-04 03:58 27 ******** ... ..( 6 skipped). .. ******** 227 2020-12-04 04:05 27 ******** 228 2020-12-04 04:06 28 ********* ... ..( 2 skipped). .. ********* 231 2020-12-04 04:09 28 ********* 232 2020-12-04 04:10 29 ********** ... ..( 3 skipped). .. ********** 236 2020-12-04 04:14 29 ********** 237 2020-12-04 04:15 30 *********** 238 2020-12-04 04:16 29 ********** 239 2020-12-04 04:17 29 ********** 240 2020-12-04 04:18 30 *********** ... ..( 15 skipped). .. *********** 256 2020-12-04 04:34 30 *********** 257 2020-12-04 04:35 31 ************ 258 2020-12-04 04:36 30 *********** 259 2020-12-04 04:37 30 *********** 260 2020-12-04 04:38 31 ************ ... ..( 28 skipped). .. ************ 289 2020-12-04 05:07 31 ************ 290 2020-12-04 05:08 32 ************* 291 2020-12-04 05:09 32 ************* 292 2020-12-04 05:10 32 ************* 293 2020-12-04 05:11 31 ************ 294 2020-12-04 05:12 32 ************* ... ..( 30 skipped). .. ************* 325 2020-12-04 05:43 32 ************* 326 2020-12-04 05:44 31 ************ 327 2020-12-04 05:45 31 ************ 328 2020-12-04 05:46 32 ************* 329 2020-12-04 05:47 31 ************ ... ..( 67 skipped). .. ************ 397 2020-12-04 06:55 31 ************ 398 2020-12-04 06:56 30 *********** 399 2020-12-04 06:57 31 ************ ... ..( 22 skipped). .. ************ 422 2020-12-04 07:20 31 ************ 423 2020-12-04 07:21 32 ************* 424 2020-12-04 07:22 31 ************ ... ..( 4 skipped). .. ************ 429 2020-12-04 07:27 31 ************ 430 2020-12-04 07:28 32 ************* 431 2020-12-04 07:29 31 ************ ... ..( 3 skipped). .. ************ 435 2020-12-04 07:33 31 ************ 436 2020-12-04 07:34 32 ************* 437 2020-12-04 07:35 31 ************ 438 2020-12-04 07:36 32 ************* 439 2020-12-04 07:37 31 ************ ... ..( 6 skipped). .. ************ 446 2020-12-04 07:44 31 ************ 447 2020-12-04 07:45 32 ************* 448 2020-12-04 07:46 31 ************ ... ..( 4 skipped). .. ************ 453 2020-12-04 07:51 31 ************ 454 2020-12-04 07:52 32 ************* 455 2020-12-04 07:53 32 ************* 456 2020-12-04 07:54 31 ************ 457 2020-12-04 07:55 32 ************* 458 2020-12-04 07:56 32 ************* 459 2020-12-04 07:57 31 ************ 460 2020-12-04 07:58 31 ************ 461 2020-12-04 07:59 31 ************ 462 2020-12-04 08:00 32 ************* 463 2020-12-04 08:01 31 ************ 464 2020-12-04 08:02 31 ************ 465 2020-12-04 08:03 32 ************* ... ..( 2 skipped). .. ************* 468 2020-12-04 08:06 32 ************* 469 2020-12-04 08:07 31 ************ 470 2020-12-04 08:08 32 ************* ... ..( 14 skipped). .. ************* 7 2020-12-04 08:23 32 ************* 8 2020-12-04 08:24 31 ************ 9 2020-12-04 08:25 32 ************* ... ..( 70 skipped). .. ************* 80 2020-12-04 09:36 32 ************* 81 2020-12-04 09:37 31 ************ 82 2020-12-04 09:38 32 ************* ... ..( 10 skipped). .. ************* 93 2020-12-04 09:49 32 ************* 94 2020-12-04 09:50 31 ************ 95 2020-12-04 09:51 31 ************ 96 2020-12-04 09:52 32 ************* ... ..( 68 skipped). .. ************* 165 2020-12-04 11:01 32 ************* 166 2020-12-04 11:02 33 ************** 167 2020-12-04 11:03 32 ************* 168 2020-12-04 11:04 33 ************** 169 2020-12-04 11:05 32 ************* 170 2020-12-04 11:06 33 ************** 171 2020-12-04 11:07 32 ************* 172 2020-12-04 11:08 32 ************* 173 2020-12-04 11:09 32 ************* 174 2020-12-04 11:10 33 ************** 175 2020-12-04 11:11 32 ************* 176 2020-12-04 11:12 32 ************* 177 2020-12-04 11:13 ? - 178 2020-12-04 11:14 29 ********** 179 2020-12-04 11:15 29 ********** 180 2020-12-04 11:16 29 ********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 7998 Vendor specific /dev/sdg smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-56-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 860 EVO 500GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: RVT02B6Q User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Dec 4 11:16:33 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 099 099 000 - 4350 12 Power_Cycle_Count -O--CK 098 098 000 - 1013 177 Wear_Leveling_Count PO--C- 099 099 000 - 3 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 073 053 000 - 27 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 6 241 Total_LBAs_Written -O--CK 099 099 000 - 2983554307 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce-0xcf SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 21/40 Celsius Lifetime Min/Max Temperature: 19/45 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (11) Index Estimated Time Temperature Celsius 12 2020-12-03 14:00 26 ******* ... ..( 13 skipped). .. ******* 26 2020-12-03 16:20 26 ******* 27 2020-12-03 16:30 25 ****** 28 2020-12-03 16:40 25 ****** 29 2020-12-03 16:50 26 ******* ... ..( 3 skipped). .. ******* 33 2020-12-03 17:30 26 ******* 34 2020-12-03 17:40 27 ******** ... ..( 4 skipped). .. ******** 39 2020-12-03 18:30 27 ******** 40 2020-12-03 18:40 26 ******* ... ..( 4 skipped). .. ******* 45 2020-12-03 19:30 26 ******* 46 2020-12-03 19:40 25 ****** ... ..( 6 skipped). .. ****** 53 2020-12-03 20:50 25 ****** 54 2020-12-03 21:00 26 ******* 55 2020-12-03 21:10 26 ******* 56 2020-12-03 21:20 27 ******** 57 2020-12-03 21:30 26 ******* 58 2020-12-03 21:40 ? - 59 2020-12-03 21:50 21 ** 60 2020-12-03 22:00 23 **** 61 2020-12-03 22:10 24 ***** 62 2020-12-03 22:20 25 ****** 63 2020-12-03 22:30 25 ****** 64 2020-12-03 22:40 26 ******* 65 2020-12-03 22:50 ? - 66 2020-12-03 23:00 26 ******* ... ..( 7 skipped). .. ******* 74 2020-12-04 00:20 26 ******* 75 2020-12-04 00:30 25 ****** 76 2020-12-04 00:40 25 ****** 77 2020-12-04 00:50 26 ******* ... ..( 6 skipped). .. ******* 84 2020-12-04 02:00 26 ******* 85 2020-12-04 02:10 25 ****** 86 2020-12-04 02:20 26 ******* 87 2020-12-04 02:30 25 ****** ... ..( 13 skipped). .. ****** 101 2020-12-04 04:50 25 ****** 102 2020-12-04 05:00 26 ******* ... ..( 20 skipped). .. ******* 123 2020-12-04 08:30 26 ******* 124 2020-12-04 08:40 ? - 125 2020-12-04 08:50 27 ******** 126 2020-12-04 09:00 ? - 127 2020-12-04 09:10 21 ** 0 2020-12-04 09:20 22 *** 1 2020-12-04 09:30 23 **** 2 2020-12-04 09:40 24 ***** 3 2020-12-04 09:50 24 ***** 4 2020-12-04 10:00 25 ****** 5 2020-12-04 10:10 25 ****** 6 2020-12-04 10:20 25 ****** 7 2020-12-04 10:30 26 ******* ... ..( 3 skipped). .. ******* 11 2020-12-04 11:10 26 ******* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1013 --- Lifetime Power-On Resets 0x01 0x010 4 4350 --- Power-on Hours 0x01 0x018 6 2983554307 --- Logical Sectors Written 0x01 0x020 6 39054356 --- Number of Write Commands 0x01 0x028 6 2717880033 --- Logical Sectors Read 0x01 0x030 6 34009170 --- Number of Read Commands 0x01 0x038 6 2649000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 27 --- Current Temperature 0x05 0x020 1 45 --- Highest Temperature 0x05 0x028 1 19 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 4837 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC