/dev/sda === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 840 EVO 120GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EXT0CB6Q User Capacity: 120 034 123 776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Dec 12 22:35:44 2015 NOVT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Unexpected SCT status 0x0001 (action_code=4, function_code=2) Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4200) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 70) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 099 099 000 - 1876 12 Power_Cycle_Count -O--CK 099 099 000 - 529 177 Wear_Leveling_Count PO--C- 098 098 000 - 15 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 068 058 000 - 32 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 55 241 Total_LBAs_Written -O--CK 099 099 000 - 4343442019 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 16 Device vendor specific log 0xce GPL,SL VS 16 Device vendor specific log 0xde SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) SCT Support Level: 1 Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: ?/ ? Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/11240 SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: ?/ ? Celsius Min/Max Temperature Limit: ?/ ? Celsius Temperature History Size (Index): 128 (39) Index Estimated Time Temperature Celsius 40 2015-12-12 01:20 ? - ... ..( 87 skipped). .. - 0 2015-12-12 16:00 ? - 1 2015-12-12 16:10 29 ********** 2 2015-12-12 16:20 31 ************ ... ..( 4 skipped). .. ************ 7 2015-12-12 17:10 31 ************ 8 2015-12-12 17:20 32 ************* 9 2015-12-12 17:30 31 ************ 10 2015-12-12 17:40 32 ************* 11 2015-12-12 17:50 32 ************* 12 2015-12-12 18:00 33 ************** 13 2015-12-12 18:10 33 ************** 14 2015-12-12 18:20 34 *************** 15 2015-12-12 18:30 32 ************* 16 2015-12-12 18:40 32 ************* 17 2015-12-12 18:50 31 ************ ... ..( 10 skipped). .. ************ 28 2015-12-12 20:40 31 ************ 29 2015-12-12 20:50 32 ************* ... ..( 9 skipped). .. ************* 39 2015-12-12 22:30 32 ************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 36 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 36 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3320620AS Serial Number: -- Firmware Version: 3.AAE User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sat Dec 12 22:35:45 2015 NOVT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 115) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 094 083 006 - 91975973 3 Spin_Up_Time PO---- 095 095 000 - 0 4 Start_Stop_Count -O--CK 095 095 020 - 5576 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 089 060 030 - 855150667 9 Power_On_Hours -O--CK 080 080 000 - 18284 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 094 094 020 - 6270 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 062 046 045 - 38 (Min/Max 25/39) 194 Temperature_Celsius -O---K 038 054 000 - 38 (0 19 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 056 047 000 - 15805543 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 108 000 - 6367 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 8779 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 8779 [18] occurred at disk power-on lifetime: 12561 hours (523 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 6f 00 00 00 00 00 00 40 00 Error: ICRC, ABRT 111 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 01 f5 00 68 00 40 00 02:51:06.905 READ DMA EXT 25 00 ff 00 28 00 01 c8 00 52 90 40 00 02:51:06.905 READ DMA EXT 25 00 ff 00 20 00 01 dc 00 51 98 40 00 02:51:06.904 READ DMA EXT 25 00 ff 00 20 00 01 dc 00 51 78 40 00 02:51:06.904 READ DMA EXT 25 00 ff 00 20 00 01 dc 00 51 58 40 00 02:51:06.904 READ DMA EXT Error 8778 [17] occurred at disk power-on lifetime: 12561 hours (523 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 00 20 00 00 69 00 aa 80 40 00 02:45:13.621 READ DMA EXT 25 00 ff 00 80 00 00 a8 00 04 d0 40 00 02:45:13.607 READ DMA EXT 25 00 ff 00 80 00 00 a8 00 04 50 40 00 02:45:13.606 READ DMA EXT 25 00 ff 00 08 00 00 69 00 aa 78 40 00 02:45:13.593 READ DMA EXT 25 00 ff 00 18 00 00 68 00 aa e0 40 00 02:45:13.581 READ DMA EXT Error 8777 [16] occurred at disk power-on lifetime: 12561 hours (523 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 00 20 00 00 a0 00 e6 c8 40 00 02:44:59.782 READ DMA EXT 25 00 ff 00 20 00 00 a0 00 e6 a8 40 00 02:44:59.781 READ DMA EXT 25 00 ff 00 20 00 00 a0 00 e6 88 40 00 02:44:59.781 READ DMA EXT 25 00 ff 00 20 00 00 a0 00 e6 68 40 00 02:44:59.780 READ DMA EXT 25 00 ff 00 20 00 00 a0 00 e6 48 40 00 02:44:59.780 READ DMA EXT Error 8776 [15] occurred at disk power-on lifetime: 12561 hours (523 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 5f 00 00 00 00 00 00 40 00 Error: ICRC, ABRT 95 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 dc 00 db c0 40 00 02:43:25.278 READ DMA EXT 25 00 ff 00 20 00 01 bb 00 22 28 40 00 02:43:25.269 READ DMA EXT 25 00 ff 01 00 00 00 db 00 db c0 40 00 02:43:25.261 READ DMA EXT 25 00 ff 00 08 00 01 bb 00 22 20 40 00 02:43:25.261 READ DMA EXT 25 00 ff 00 18 00 01 ba 00 22 88 40 00 02:43:25.356 READ DMA EXT Error 8775 [14] occurred at disk power-on lifetime: 12561 hours (523 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 5f 00 00 00 00 00 00 40 00 Error: ICRC, ABRT 95 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 00 80 00 00 90 00 91 f8 40 00 02:43:09.488 READ DMA EXT 25 00 ff 00 20 00 01 aa 00 58 c8 40 00 02:43:09.477 READ DMA EXT 25 00 ff 00 80 00 00 8f 00 91 78 40 00 02:43:09.471 READ DMA EXT 25 00 ff 00 80 00 00 8d 00 91 f8 40 00 02:43:09.459 READ DMA EXT 25 00 ff 00 20 00 01 aa 00 58 a8 40 00 02:43:09.446 READ DMA EXT Error 8774 [13] occurred at disk power-on lifetime: 12561 hours (523 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 6f 00 00 00 00 00 00 40 00 Error: ICRC, ABRT 111 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 00 80 00 01 bd 00 00 40 40 00 02:40:28.816 READ DMA EXT 25 00 ff 00 80 00 00 aa 00 f4 c0 40 00 02:40:28.845 READ DMA EXT 25 00 ff 00 20 00 00 b6 00 f1 88 40 00 02:40:28.835 READ DMA EXT 25 00 ff 00 80 00 00 a9 00 f4 c0 40 00 02:40:28.826 READ DMA EXT 25 00 ff 00 80 00 00 a8 00 f4 c0 40 00 02:40:28.825 READ DMA EXT Error 8773 [12] occurred at disk power-on lifetime: 12561 hours (523 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 9f 00 00 00 00 00 00 40 00 Error: ICRC, ABRT 159 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 01 67 00 62 00 40 00 02:38:14.591 READ DMA EXT 25 00 ff 00 20 00 01 85 00 66 a8 40 00 02:38:14.586 READ DMA EXT 25 00 ff 01 00 00 01 66 00 62 00 40 00 02:38:14.574 READ DMA EXT 25 00 ff 00 20 00 01 85 00 66 88 40 00 02:38:14.568 READ DMA EXT 25 00 ff 01 00 00 01 65 00 62 00 40 00 02:38:14.558 READ DMA EXT Error 8772 [11] occurred at disk power-on lifetime: 12561 hours (523 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 6f 00 00 00 00 00 00 40 00 Error: ICRC, ABRT 111 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 45 00 20 50 40 00 02:36:42.399 READ DMA EXT 35 00 ff 01 00 00 02 44 00 09 d0 40 00 02:36:42.396 WRITE DMA EXT 35 00 ff 01 00 00 02 43 00 09 d0 40 00 02:36:42.395 WRITE DMA EXT 35 00 ff 01 00 00 02 42 00 09 d0 40 00 02:36:42.393 WRITE DMA EXT 35 00 ff 01 00 00 02 41 00 09 d0 40 00 02:36:42.392 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 29 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD5000BEVT-22A0RT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500 107 862 016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Dec 12 22:35:45 2015 NOVT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 154) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 181 153 021 - 1925 4 Start_Stop_Count -O--CK 090 090 000 - 10952 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 087 087 000 - 9978 10 Spin_Retry_Count -O--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4191 191 G-Sense_Error_Rate -O--CK 001 001 000 - 366 192 Power-Off_Retract_Count -O--CK 199 199 000 - 1411 193 Load_Cycle_Count -O--CK 103 103 000 - 292555 194 Temperature_Celsius -O---K 115 090 000 - 32 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 828 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 828 [11] occurred at disk power-on lifetime: 7967 hours (331 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 52 f4 ea 40 00 Error: UNC at LBA = 0x0252f4ea = 38991082 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 30 00 58 00 00 00 0f d8 23 40 00 08:32:00.244 READ FPDMA QUEUED 60 00 40 00 58 00 00 00 0f d7 e3 40 00 08:32:00.232 READ FPDMA QUEUED 61 00 08 00 48 00 00 00 63 45 f0 40 00 08:32:00.227 WRITE FPDMA QUEUED 61 00 08 00 48 00 00 00 63 28 68 40 00 08:32:00.227 WRITE FPDMA QUEUED 61 00 08 00 48 00 00 00 64 62 50 40 00 08:32:00.227 WRITE FPDMA QUEUED Error 827 [10] occurred at disk power-on lifetime: 7967 hours (331 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 52 f4 ea 40 00 Error: UNC at LBA = 0x0252f4ea = 38991082 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 38 00 00 03 3c 8d e8 40 00 08:31:57.685 READ FPDMA QUEUED 60 00 40 00 30 00 00 00 0f d7 4b 40 00 08:31:57.671 READ FPDMA QUEUED 60 00 1f 00 30 00 00 00 0f e1 3c 40 00 08:31:57.666 READ FPDMA QUEUED 60 00 20 00 18 00 00 00 0f de 1c 40 00 08:31:57.658 READ FPDMA QUEUED 60 00 40 00 10 00 00 00 0f d8 53 40 00 08:31:57.658 READ FPDMA QUEUED Error 826 [9] occurred at disk power-on lifetime: 7967 hours (331 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 52 f4 ea 40 00 Error: UNC at LBA = 0x0252f4ea = 38991082 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 b8 00 00 03 e5 4e 08 40 00 08:31:55.183 READ FPDMA QUEUED 60 00 20 00 b0 00 00 02 c6 68 63 40 00 08:31:55.176 READ FPDMA QUEUED 60 00 40 00 a8 00 00 00 0f d8 93 40 00 08:31:55.170 READ FPDMA QUEUED 60 00 20 00 a0 00 00 00 0f dd 45 40 00 08:31:55.169 READ FPDMA QUEUED 60 00 18 00 98 00 00 00 51 54 c8 40 00 08:31:55.158 READ FPDMA QUEUED Error 825 [8] occurred at disk power-on lifetime: 7967 hours (331 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 52 f4 ea 40 00 Error: UNC at LBA = 0x0252f4ea = 38991082 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 28 00 00 00 0a e8 f8 40 00 08:31:52.611 READ FPDMA QUEUED 60 00 08 00 a8 00 00 03 e5 4e b8 40 00 08:31:52.602 READ FPDMA QUEUED 60 00 60 00 40 00 00 02 52 f4 a0 40 00 08:31:52.602 READ FPDMA QUEUED 60 00 18 00 38 00 00 00 29 cc 8c 40 00 08:31:52.602 READ FPDMA QUEUED 60 00 40 00 30 00 00 00 a6 b6 5a 40 00 08:31:52.602 READ FPDMA QUEUED Error 824 [7] occurred at disk power-on lifetime: 7967 hours (331 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 52 f4 ea 40 00 Error: UNC at LBA = 0x0252f4ea = 38991082 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 88 00 00 02 c6 68 43 40 00 08:31:50.125 READ FPDMA QUEUED 60 00 40 00 80 00 00 00 0c 2b 63 40 00 08:31:50.115 READ FPDMA QUEUED 60 00 03 00 78 00 00 00 0b 53 0f 40 00 08:31:50.114 READ FPDMA QUEUED 60 00 2c 00 70 00 00 00 0b 52 c2 40 00 08:31:50.114 READ FPDMA QUEUED 60 00 08 00 68 00 00 00 0b 52 ee 40 00 08:31:50.113 READ FPDMA QUEUED Error 823 [6] occurred at disk power-on lifetime: 7967 hours (331 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 52 f4 ea 40 00 Error: UNC at LBA = 0x0252f4ea = 38991082 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 50 00 00 02 92 ff 98 40 00 08:31:47.624 READ FPDMA QUEUED 60 00 20 00 48 00 00 02 c6 67 fb 40 00 08:31:47.623 READ FPDMA QUEUED 60 00 40 00 48 00 00 02 92 fe a8 40 00 08:31:47.620 READ FPDMA QUEUED 60 00 40 00 48 00 00 02 92 ff 18 40 00 08:31:47.619 READ FPDMA QUEUED 60 00 40 00 40 00 00 02 66 f8 12 40 00 08:31:47.610 READ FPDMA QUEUED Error 822 [5] occurred at disk power-on lifetime: 7967 hours (331 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 52 f4 ea 40 00 Error: UNC at LBA = 0x0252f4ea = 38991082 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 38 00 00 00 64 1c 38 40 00 08:31:45.084 READ FPDMA QUEUED 61 00 08 00 40 00 00 00 5e b3 80 40 00 08:31:45.076 WRITE FPDMA QUEUED 61 00 08 00 40 00 00 00 5e b3 90 40 00 08:31:45.075 WRITE FPDMA QUEUED 60 00 40 00 50 00 00 02 93 0a 30 40 00 08:31:45.075 READ FPDMA QUEUED 60 00 1a 00 48 00 00 02 66 f8 b8 40 00 08:31:45.075 READ FPDMA QUEUED Error 821 [4] occurred at disk power-on lifetime: 7967 hours (331 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 52 f4 ea 40 00 Error: UNC at LBA = 0x0252f4ea = 38991082 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 40 00 00 00 b3 b1 b8 40 00 08:31:42.597 READ FPDMA QUEUED 60 00 08 00 38 00 00 02 8f 27 68 40 00 08:31:42.597 READ FPDMA QUEUED 60 00 68 00 30 00 00 02 52 f4 98 40 00 08:31:42.597 READ FPDMA QUEUED 60 00 40 00 28 00 00 02 c4 85 f2 40 00 08:31:42.597 READ FPDMA QUEUED 60 00 08 00 20 00 00 02 cf 43 38 40 00 08:31:42.597 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 27/33 Celsius Lifetime Min/Max Temperature: 27/57 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (25) Index Estimated Time Temperature Celsius 26 2015-12-12 20:28 31 ************ ... ..( 32 skipped). .. ************ 59 2015-12-12 21:01 31 ************ 60 2015-12-12 21:02 32 ************* 61 2015-12-12 21:03 31 ************ ... ..( 13 skipped). .. ************ 75 2015-12-12 21:17 31 ************ 76 2015-12-12 21:18 32 ************* 77 2015-12-12 21:19 31 ************ ... ..( 8 skipped). .. ************ 86 2015-12-12 21:28 31 ************ 87 2015-12-12 21:29 32 ************* 88 2015-12-12 21:30 31 ************ 89 2015-12-12 21:31 32 ************* 90 2015-12-12 21:32 31 ************ ... ..( 5 skipped). .. ************ 96 2015-12-12 21:38 31 ************ 97 2015-12-12 21:39 32 ************* 98 2015-12-12 21:40 31 ************ 99 2015-12-12 21:41 32 ************* 100 2015-12-12 21:42 31 ************ 101 2015-12-12 21:43 32 ************* ... ..( 9 skipped). .. ************* 111 2015-12-12 21:53 32 ************* 112 2015-12-12 21:54 31 ************ 113 2015-12-12 21:55 31 ************ 114 2015-12-12 21:56 32 ************* 115 2015-12-12 21:57 31 ************ 116 2015-12-12 21:58 31 ************ 117 2015-12-12 21:59 31 ************ 118 2015-12-12 22:00 32 ************* 119 2015-12-12 22:01 31 ************ 120 2015-12-12 22:02 31 ************ 121 2015-12-12 22:03 32 ************* ... ..( 12 skipped). .. ************* 6 2015-12-12 22:16 32 ************* 7 2015-12-12 22:17 31 ************ 8 2015-12-12 22:18 32 ************* ... ..( 2 skipped). .. ************* 11 2015-12-12 22:21 32 ************* 12 2015-12-12 22:22 31 ************ 13 2015-12-12 22:23 32 ************* ... ..( 2 skipped). .. ************* 16 2015-12-12 22:26 32 ************* 17 2015-12-12 22:27 31 ************ 18 2015-12-12 22:28 32 ************* 19 2015-12-12 22:29 31 ************ 20 2015-12-12 22:30 32 ************* 21 2015-12-12 22:31 32 ************* 22 2015-12-12 22:32 31 ************ 23 2015-12-12 22:33 31 ************ 24 2015-12-12 22:34 31 ************ 25 2015-12-12 22:35 32 ************* SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 23409 Vendor specific