Probe #725f72bc26 of Foxconn 2ABF Desktop Computer by HP (G5403ru)

Log: smartctl

/dev/sda === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" DT01ACA... Desktop HDD Device Model: TOSHIBA DT01ACA100 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MS2OA750 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Jun 1 03:09:51 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7119) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 119) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 1 2 Throughput_Performance P-S--- 142 142 054 - 70 3 Spin_Up_Time POS--- 131 131 024 - 178 (Average 172) 4 Start_Stop_Count -O--C- 100 100 000 - 2046 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 115 115 020 - 34 9 Power_On_Hours -O--C- 099 099 000 - 7995 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 781 192 Power-Off_Retract_Count -O--CK 099 099 000 - 2048 193 Load_Cycle_Count -O--C- 099 099 000 - 2048 194 Temperature_Celsius -O---- 150 150 000 - 40 (Min/Max 19/52) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 7592 hours (316 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 11 00 00 00 2f fc 17 00 00 Error: ICRC, ABRT at LBA = 0x002ffc17 = 3144727 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 28 00 00 00 2f fc 08 40 00 01:21:17.128 READ FPDMA QUEUED 60 00 08 00 20 00 00 00 61 ca 88 40 00 01:21:17.038 READ FPDMA QUEUED 60 00 08 00 18 00 00 00 61 ca 80 40 00 01:21:17.026 READ FPDMA QUEUED 60 01 00 00 10 00 00 6d 37 4a b0 40 00 01:21:16.733 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 01:21:16.371 FLUSH CACHE EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 90% 3939 - # 2 Short offline Completed without error 00% 3939 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 40/43 Celsius Lifetime Min/Max Temperature: 19/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (75) Index Estimated Time Temperature Celsius 76 2018-06-01 01:02 41 ********************** ... ..( 32 skipped). .. ********************** 109 2018-06-01 01:35 41 ********************** 110 2018-06-01 01:36 42 *********************** 111 2018-06-01 01:37 41 ********************** 112 2018-06-01 01:38 42 *********************** 113 2018-06-01 01:39 ? - 114 2018-06-01 01:40 ? - 115 2018-06-01 01:41 41 ********************** 116 2018-06-01 01:42 41 ********************** 117 2018-06-01 01:43 42 *********************** ... ..( 12 skipped). .. *********************** 2 2018-06-01 01:56 42 *********************** 3 2018-06-01 01:57 ? - 4 2018-06-01 01:58 ? - 5 2018-06-01 01:59 42 *********************** 6 2018-06-01 02:00 43 ************************ ... ..( 20 skipped). .. ************************ 27 2018-06-01 02:21 43 ************************ 28 2018-06-01 02:22 42 *********************** 29 2018-06-01 02:23 43 ************************ 30 2018-06-01 02:24 43 ************************ 31 2018-06-01 02:25 42 *********************** ... ..( 20 skipped). .. *********************** 52 2018-06-01 02:46 42 *********************** 53 2018-06-01 02:47 41 ********************** 54 2018-06-01 02:48 42 *********************** 55 2018-06-01 02:49 41 ********************** ... ..( 11 skipped). .. ********************** 67 2018-06-01 03:01 41 ********************** 68 2018-06-01 03:02 40 ********************* ... ..( 3 skipped). .. ********************* 72 2018-06-01 03:06 40 ********************* 73 2018-06-01 03:07 41 ********************** 74 2018-06-01 03:08 40 ********************* 75 2018-06-01 03:09 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 781 --- Lifetime Power-On Resets 0x01 0x010 4 7995 --- Power-on Hours 0x01 0x018 6 32750181310 --- Logical Sectors Written 0x01 0x020 6 355098448 --- Number of Write Commands 0x01 0x028 6 255409168188 --- Logical Sectors Read 0x01 0x030 6 509412406 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 7021 --- Spindle Motor Power-on Hours 0x03 0x010 4 7021 --- Head Flying Hours 0x03 0x018 4 2048 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 97 --- Read Recovery Attempts 0x03 0x030 4 7 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 1 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 40 --- Current Temperature 0x05 0x010 1 41 N-- Average Short Term Temperature 0x05 0x018 1 41 N-- Average Long Term Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 19 --- Lowest Temperature 0x05 0x030 1 47 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 43 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 6681 --- Number of Hardware Resets 0x06 0x010 4 2305 --- Number of ASR Events 0x06 0x018 4 1 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 65535+ Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST3500418AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: HP40 User Capacity: 500 107 862 016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Jun 1 03:09:54 2018 MSK ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213891en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 592) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 78) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 117 094 006 - 151406427 3 Spin_Up_Time PO---K 097 097 000 - 0 4 Start_Stop_Count -O--CK 092 092 020 - 8689 5 Reallocated_Sector_Ct PO--CK 093 093 036 - 307 7 Seek_Error_Rate POSR-K 082 060 030 - 179880336 9 Power_On_Hours -O--CK 067 067 000 - 29564 10 Spin_Retry_Count PO--CK 100 100 097 - 0 12 Power_Cycle_Count -O--CK 097 097 020 - 3105 180 Unknown_HDD_Attribute PO-R-K 100 001 000 - 852231 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 096 096 097 NOW 4 187 Reported_Uncorrect -O--CK 001 001 000 - 339 188 Command_Timeout -O--CK 100 098 000 - 395143020666 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 065 054 045 - 35 (Min/Max 30/38) 194 Temperature_Celsius -O---K 035 046 000 - 35 (0 10 0 0 0) 195 Hardware_ECC_Recovered -O-RCK 030 019 000 - 151406427 196 Reallocated_Event_Count -O--CK 093 093 036 - 307 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 2 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 521 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 521 [0] occurred at disk power-on lifetime: 26844 hours (1118 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 00 32 01 80 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 00 00 00 00 00 00 00 00 00 03:57:22.967 IDENTIFY DEVICE 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:57:16.131 NOP [Abort queued commands] ec 00 00 00 00 00 00 00 00 00 00 00 00 03:55:54.377 IDENTIFY DEVICE 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:55:47.543 NOP [Abort queued commands] ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:55:46.953 IDENTIFY DEVICE Error 520 [19] occurred at disk power-on lifetime: 26844 hours (1118 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 00 32 01 80 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 00 00 00 00 00 00 00 00 00 03:55:54.377 IDENTIFY DEVICE 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:55:47.543 NOP [Abort queued commands] ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:55:46.953 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:55:46.919 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:55:46.918 IDENTIFY DEVICE Error 519 [18] occurred at disk power-on lifetime: 26844 hours (1118 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 00 32 01 80 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:55:46.953 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:55:46.919 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:55:46.918 IDENTIFY DEVICE 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:55:46.898 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:55:43.703 NOP [Abort queued commands] Error 518 [17] occurred at disk power-on lifetime: 26844 hours (1118 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 00 32 01 80 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:55:46.919 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:55:46.918 IDENTIFY DEVICE 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:55:46.898 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:55:43.703 NOP [Abort queued commands] 60 00 00 00 80 00 00 1c ec 24 78 40 00 03:55:43.702 READ FPDMA QUEUED Error 517 [16] occurred at disk power-on lifetime: 26844 hours (1118 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 00 32 01 80 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 00 00 00 00 00 00 00 a0 00 03:55:46.918 IDENTIFY DEVICE 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:55:46.898 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:55:43.703 NOP [Abort queued commands] 60 00 00 00 80 00 00 1c ec 24 78 40 00 03:55:43.702 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 03:55:42.898 SET FEATURES [Disable SATA feature] Error 516 [15] occurred at disk power-on lifetime: 26844 hours (1118 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 00 32 01 80 40 00 Device Fault; Error: ABRT at LBA = 0x00320180 = 3277184 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 00 1c ec 24 78 40 00 03:55:43.702 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 03:55:42.898 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 a0 00 03:55:42.898 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:55:42.858 NOP [Abort queued commands] 61 00 00 00 08 00 00 1c 26 86 f0 40 00 03:55:42.857 WRITE FPDMA QUEUED Error 515 [14] occurred at disk power-on lifetime: 26844 hours (1118 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 00 32 01 80 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 90 00 03 00 00 00 00 00 00 a0 00 03:55:42.898 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 a0 00 03:55:42.898 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:55:42.858 NOP [Abort queued commands] 61 00 00 00 08 00 00 1c 26 86 f0 40 00 03:55:42.857 WRITE FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 03:55:42.831 SET FEATURES [Disable SATA feature] Error 514 [13] occurred at disk power-on lifetime: 26844 hours (1118 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 03 00 00 00 32 01 80 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 02 00 00 00 00 00 00 00 00 a0 00 03:55:42.898 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 03:55:42.858 NOP [Abort queued commands] 61 00 00 00 08 00 00 1c 26 86 f0 40 00 03:55:42.857 WRITE FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 03:55:42.831 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 a0 00 03:55:42.831 SET FEATURES [Enable write cache] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: unknown failure 90% 28006 0 # 2 Short offline Completed: unknown failure 90% 26844 0 # 3 Short offline Completed: unknown failure 90% 20317 0 # 4 Short offline Completed: unknown failure 90% 20317 0 # 5 Short offline Completed: unknown failure 90% 20201 0 # 6 Short offline Completed: unknown failure 90% 17721 0 # 7 Extended offline Interrupted (host reset) 90% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 30/38 Celsius Lifetime Min/Max Temperature: 10/46 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (87) Index Estimated Time Temperature Celsius 88 2018-05-26 22:02 ? - 89 2018-05-26 23:01 23 **** 90 2018-05-27 00:00 23 **** 91 2018-05-27 00:59 37 ****************** 92 2018-05-27 01:58 38 ******************* 93 2018-05-27 02:57 38 ******************* 94 2018-05-27 03:56 35 **************** 95 2018-05-27 04:55 38 ******************* 96 2018-05-27 05:54 32 ************* 97 2018-05-27 06:53 38 ******************* 98 2018-05-27 07:52 35 **************** 99 2018-05-27 08:51 39 ******************** 100 2018-05-27 09:50 ? - 101 2018-05-27 10:49 21 ** 102 2018-05-27 11:48 21 ** 103 2018-05-27 12:47 ? - 104 2018-05-27 13:46 36 ***************** 105 2018-05-27 14:45 ? - 106 2018-05-27 15:44 38 ******************* 107 2018-05-27 16:43 38 ******************* 108 2018-05-27 17:42 39 ******************** 109 2018-05-27 18:41 39 ******************** 110 2018-05-27 19:40 39 ******************** 111 2018-05-27 20:39 ? - 112 2018-05-27 21:38 38 ******************* 113 2018-05-27 22:37 ? - 114 2018-05-27 23:36 38 ******************* 115 2018-05-28 00:35 38 ******************* 116 2018-05-28 01:34 ? - 117 2018-05-28 02:33 21 ** 118 2018-05-28 03:32 ? - 119 2018-05-28 04:31 23 **** 120 2018-05-28 05:30 23 **** 121 2018-05-28 06:29 ? - 122 2018-05-28 07:28 38 ******************* 123 2018-05-28 08:27 38 ******************* 124 2018-05-28 09:26 40 ********************* 125 2018-05-28 10:25 ? - 126 2018-05-28 11:24 40 ********************* 127 2018-05-28 12:23 40 ********************* 0 2018-05-28 13:22 36 ***************** 1 2018-05-28 14:21 40 ********************* 2 2018-05-28 15:20 ? - 3 2018-05-28 16:19 23 **** 4 2018-05-28 17:18 23 **** 5 2018-05-28 18:17 37 ****************** 6 2018-05-28 19:16 39 ******************** 7 2018-05-28 20:15 39 ******************** 8 2018-05-28 21:14 38 ******************* 9 2018-05-28 22:13 38 ******************* 10 2018-05-28 23:12 38 ******************* 11 2018-05-29 00:11 ? - 12 2018-05-29 01:10 37 ****************** 13 2018-05-29 02:09 ? - 14 2018-05-29 03:08 37 ****************** 15 2018-05-29 04:07 37 ****************** 16 2018-05-29 05:06 ? - 17 2018-05-29 06:05 38 ******************* 18 2018-05-29 07:04 38 ******************* 19 2018-05-29 08:03 36 ***************** 20 2018-05-29 09:02 ? - 21 2018-05-29 10:01 39 ******************** 22 2018-05-29 11:00 39 ******************** 23 2018-05-29 11:59 39 ******************** 24 2018-05-29 12:58 ? - 25 2018-05-29 13:57 38 ******************* 26 2018-05-29 14:56 ? - 27 2018-05-29 15:55 21 ** 28 2018-05-29 16:54 22 *** 29 2018-05-29 17:53 38 ******************* 30 2018-05-29 18:52 39 ******************** 31 2018-05-29 19:51 ? - 32 2018-05-29 20:50 38 ******************* 33 2018-05-29 21:49 38 ******************* 34 2018-05-29 22:48 ? - 35 2018-05-29 23:47 21 ** 36 2018-05-30 00:46 22 *** 37 2018-05-30 01:45 ? - 38 2018-05-30 02:44 22 *** 39 2018-05-30 03:43 22 *** 40 2018-05-30 04:42 ? - 41 2018-05-30 05:41 37 ****************** 42 2018-05-30 06:40 37 ****************** 43 2018-05-30 07:39 38 ******************* 44 2018-05-30 08:38 ? - 45 2018-05-30 09:37 38 ******************* 46 2018-05-30 10:36 ? - 47 2018-05-30 11:35 39 ******************** 48 2018-05-30 12:34 39 ******************** 49 2018-05-30 13:33 39 ******************** 50 2018-05-30 14:32 38 ******************* 51 2018-05-30 15:31 38 ******************* 52 2018-05-30 16:30 ? - 53 2018-05-30 17:29 22 *** 54 2018-05-30 18:28 ? - 55 2018-05-30 19:27 38 ******************* 56 2018-05-30 20:26 38 ******************* 57 2018-05-30 21:25 39 ******************** 58 2018-05-30 22:24 39 ******************** 59 2018-05-30 23:23 39 ******************** 60 2018-05-31 00:22 38 ******************* 61 2018-05-31 01:21 ? - 62 2018-05-31 02:20 21 ** 63 2018-05-31 03:19 21 ** 64 2018-05-31 04:18 35 **************** 65 2018-05-31 05:17 ? - 66 2018-05-31 06:16 37 ****************** 67 2018-05-31 07:15 ? - 68 2018-05-31 08:14 37 ****************** 69 2018-05-31 09:13 37 ****************** 70 2018-05-31 10:12 38 ******************* 71 2018-05-31 11:11 ? - 72 2018-05-31 12:10 38 ******************* 73 2018-05-31 13:09 ? - 74 2018-05-31 14:08 35 **************** 75 2018-05-31 15:07 35 **************** 76 2018-05-31 16:06 ? - 77 2018-05-31 17:05 39 ******************** 78 2018-05-31 18:04 ? - 79 2018-05-31 19:03 34 *************** 80 2018-05-31 20:02 ? - 81 2018-05-31 21:01 34 *************** 82 2018-05-31 22:00 ? - 83 2018-05-31 22:59 37 ****************** 84 2018-05-31 23:58 ? - 85 2018-06-01 00:57 36 ***************** 86 2018-06-01 01:56 37 ****************** 87 2018-06-01 02:55 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS


Hardware for Linux and BSD

GitHub