/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green Device Model: WDC WD10EADS-00L5B1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sun Jan 8 21:47:46 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (22800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 262) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 168 163 021 - 6600 4 Start_Stop_Count -O--CK 083 083 000 - 17203 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 059 059 000 - 30587 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 089 089 000 - 11409 192 Power-Off_Retract_Count -O--CK 200 200 000 - 259 193 Load_Cycle_Count -O--CK 195 195 000 - 17192 194 Temperature_Celsius -O---K 123 097 000 - 27 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 494 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 421 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 421 [12] occurred at disk power-on lifetime: 8594 hours (358 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 53 00 10 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 c2 00 4f 00 e0 a0 00 00:12:03.375 SMART WRITE LOG ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:12:03.374 IDENTIFY DEVICE c6 00 00 00 10 00 00 00 00 00 00 a0 00 00:12:01.767 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 00 00:12:01.767 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 00 00:12:01.767 SET FEATURES [Set transfer mode] Error 420 [11] occurred at disk power-on lifetime: 6943 hours (289 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 53 00 10 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 c2 00 4f 00 e0 a0 00 00:04:45.261 SMART WRITE LOG ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:04:45.260 IDENTIFY DEVICE c6 00 00 00 10 00 00 00 00 00 00 a0 00 00:04:43.714 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 00 00:04:43.714 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 00 00:04:43.714 SET FEATURES [Set transfer mode] Error 419 [10] occurred at disk power-on lifetime: 6942 hours (289 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 53 ff 01 00 c2 00 4f 00 e0 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 c2 00 4f 00 e0 a0 00 00:08:02.656 SMART WRITE LOG ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:02.656 IDENTIFY DEVICE c6 00 00 00 10 00 00 00 00 00 00 a0 00 00:08:01.427 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 00 00:08:01.427 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 00 00:08:01.427 SET FEATURES [Set transfer mode] Error 418 [9] occurred at disk power-on lifetime: 6942 hours (289 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 53 ff 01 00 c2 00 4f 00 e0 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 c2 00 4f 00 e0 a0 00 00:06:21.639 SMART WRITE LOG ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:06:21.637 IDENTIFY DEVICE c6 00 00 00 10 00 00 00 00 00 00 a0 00 00:06:20.307 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 00 00:06:20.307 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 00 00:06:20.306 SET FEATURES [Set transfer mode] Error 417 [8] occurred at disk power-on lifetime: 6942 hours (289 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 53 ff 01 00 c2 00 4f 00 e0 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 c2 00 4f 00 e0 a0 00 00:05:09.200 SMART WRITE LOG ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:05:09.200 IDENTIFY DEVICE c6 00 00 00 10 00 00 00 00 00 00 a0 00 00:05:07.497 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 00 00:05:07.497 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 00 00:05:07.497 SET FEATURES [Set transfer mode] Error 416 [7] occurred at disk power-on lifetime: 6942 hours (289 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 53 00 10 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 c2 00 4f 00 e0 a0 00 00:01:22.257 SMART WRITE LOG ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:22.255 IDENTIFY DEVICE c6 00 00 00 10 00 00 00 00 00 00 a0 00 00:01:21.084 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 00 00:01:21.084 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 00 00:01:21.084 SET FEATURES [Set transfer mode] Error 415 [6] occurred at disk power-on lifetime: 6942 hours (289 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 53 00 10 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 c2 00 4f 00 e0 a0 00 00:01:16.659 SMART WRITE LOG ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:16.658 IDENTIFY DEVICE c6 00 00 00 10 00 00 00 00 00 00 a0 00 00:01:15.138 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 00 00:01:15.138 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 00 00:01:15.138 SET FEATURES [Set transfer mode] Error 414 [5] occurred at disk power-on lifetime: 6942 hours (289 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 53 00 10 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 c2 00 4f 00 e0 a0 00 00:02:48.494 SMART WRITE LOG ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:02:48.493 IDENTIFY DEVICE c6 00 00 00 10 00 00 00 00 00 00 a0 00 00:02:47.301 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 00 00:02:47.301 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 00 00:02:47.301 SET FEATURES [Set transfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 20/27 Celsius Lifetime Min/Max Temperature: 17/53 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (153) Index Estimated Time Temperature Celsius 154 2023-01-08 13:50 27 ******** ... ..( 24 skipped). .. ******** 179 2023-01-08 14:15 27 ******** 180 2023-01-08 14:16 28 ********* ... ..( 38 skipped). .. ********* 219 2023-01-08 14:55 28 ********* 220 2023-01-08 14:56 29 ********** ... ..( 2 skipped). .. ********** 223 2023-01-08 14:59 29 ********** 224 2023-01-08 15:00 28 ********* 225 2023-01-08 15:01 29 ********** 226 2023-01-08 15:02 29 ********** 227 2023-01-08 15:03 29 ********** 228 2023-01-08 15:04 28 ********* 229 2023-01-08 15:05 28 ********* 230 2023-01-08 15:06 29 ********** 231 2023-01-08 15:07 29 ********** 232 2023-01-08 15:08 28 ********* ... ..( 6 skipped). .. ********* 239 2023-01-08 15:15 28 ********* 240 2023-01-08 15:16 29 ********** ... ..(186 skipped). .. ********** 427 2023-01-08 18:23 29 ********** 428 2023-01-08 18:24 28 ********* 429 2023-01-08 18:25 28 ********* 430 2023-01-08 18:26 29 ********** 431 2023-01-08 18:27 28 ********* ... ..( 41 skipped). .. ********* 473 2023-01-08 19:09 28 ********* 474 2023-01-08 19:10 27 ******** 475 2023-01-08 19:11 28 ********* ... ..( 17 skipped). .. ********* 15 2023-01-08 19:29 28 ********* 16 2023-01-08 19:30 29 ********** ... ..( 5 skipped). .. ********** 22 2023-01-08 19:36 29 ********** 23 2023-01-08 19:37 ? - 24 2023-01-08 19:38 18 - 25 2023-01-08 19:39 19 - 26 2023-01-08 19:40 20 * ... ..( 3 skipped). .. * 30 2023-01-08 19:44 20 * 31 2023-01-08 19:45 21 ** ... ..( 2 skipped). .. ** 34 2023-01-08 19:48 21 ** 35 2023-01-08 19:49 22 *** 36 2023-01-08 19:50 23 **** ... ..( 2 skipped). .. **** 39 2023-01-08 19:53 23 **** 40 2023-01-08 19:54 24 ***** 41 2023-01-08 19:55 25 ****** ... ..( 3 skipped). .. ****** 45 2023-01-08 19:59 25 ****** 46 2023-01-08 20:00 26 ******* ... ..( 3 skipped). .. ******* 50 2023-01-08 20:04 26 ******* 51 2023-01-08 20:05 27 ******** ... ..( 8 skipped). .. ******** 60 2023-01-08 20:14 27 ******** 61 2023-01-08 20:15 28 ********* 62 2023-01-08 20:16 28 ********* 63 2023-01-08 20:17 28 ********* 64 2023-01-08 20:18 ? - 65 2023-01-08 20:19 20 * 66 2023-01-08 20:20 20 * 67 2023-01-08 20:21 21 ** ... ..( 3 skipped). .. ** 71 2023-01-08 20:25 21 ** 72 2023-01-08 20:26 22 *** ... ..( 2 skipped). .. *** 75 2023-01-08 20:29 22 *** 76 2023-01-08 20:30 23 **** ... ..( 5 skipped). .. **** 82 2023-01-08 20:36 23 **** 83 2023-01-08 20:37 24 ***** 84 2023-01-08 20:38 24 ***** 85 2023-01-08 20:39 24 ***** 86 2023-01-08 20:40 25 ****** ... ..( 3 skipped). .. ****** 90 2023-01-08 20:44 25 ****** 91 2023-01-08 20:45 26 ******* ... ..( 8 skipped). .. ******* 100 2023-01-08 20:54 26 ******* 101 2023-01-08 20:55 27 ******** ... ..( 18 skipped). .. ******** 120 2023-01-08 21:14 27 ******** 121 2023-01-08 21:15 26 ******* ... ..( 2 skipped). .. ******* 124 2023-01-08 21:18 26 ******* 125 2023-01-08 21:19 27 ******** ... ..( 27 skipped). .. ******** 153 2023-01-08 21:47 27 ******** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x8000 4 3465 Vendor specific /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven OEM SSDs Device Model: SPCC Solid State Disk Serial Number: -- Firmware Version: S9FM02.6 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database ATA Version is: ACS-3 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jan 8 21:47:46 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 30) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0 9 Power_On_Hours -O--C- 100 100 000 - 4741 12 Power_Cycle_Count -O--C- 100 100 000 - 2198 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 0 170 Bad_Blk_Ct_Erl/Lat PO--C- 100 100 010 - 0/18 173 MaxAvgErase_Ct ------ 100 100 000 - 81 (Average 598) 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 46 194 Temperature_Celsius PO---K 070 070 000 - 30 196 Not_In_Use ------ 100 100 000 - 0 218 CRC_Error_Count ------ 100 100 000 - 0 241 Lifetime_Writes_GiB -O--C- 100 100 000 - 4834268 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4576 - # 2 Short offline Completed without error 00% 3544 - # 3 Short offline Completed without error 00% 3472 - # 4 Short offline Completed without error 00% 1295 - # 5 Short offline Completed without error 00% 1036 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 2 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron RealSSD m4/C400/P400 Device Model: M4-CT256M4SSD2 Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: 040H User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jan 8 21:47:47 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1190) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 19) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 001 - 11667 12 Power_Cycle_Count -O--CK 100 100 001 - 6767 170 Grown_Failing_Block_Ct PO--CK 100 100 010 - 0 171 Program_Fail_Count -O--CK 100 100 001 - 0 172 Erase_Fail_Count -O--CK 100 100 001 - 0 173 Wear_Leveling_Count PO--CK 097 097 010 - 102 174 Unexpect_Power_Loss_Ct -O--CK 100 100 001 - 1351 181 Non4k_Aligned_Access -O---K 100 100 001 - 3279 608 2671 183 SATA_Iface_Downshift -O--CK 100 100 001 - 0 184 End-to-End_Error PO--CK 100 100 050 - 0 187 Reported_Uncorrect -O--CK 100 100 001 - 0 188 Command_Timeout -O--CK 100 100 001 - 0 189 Factory_Bad_Block_Ct -OSR-- 100 100 001 - 98 194 Temperature_Celsius -O---K 100 100 000 - 0 195 Hardware_ECC_Recovered -O-RCK 100 100 001 - 1758 196 Reallocated_Event_Count -O--CK 100 100 001 - 0 197 Current_Pending_Sector -O--CK 100 100 001 - 0 198 Offline_Uncorrectable ----CK 100 100 001 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 001 - 47 202 Perc_Rated_Life_Used ---RC- 097 097 001 - 3 206 Write_Error_Rate -OSR-- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 16383 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 3449 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL VS 2000 Device vendor specific log 0xa0 SL VS 208 Device vendor specific log 0xa1-0xbf GPL,SL VS 1 Device vendor specific log 0xc0 GPL VS 80 Device vendor specific log 0xc1-0xdf GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (16383 sectors) No Errors Logged SMART Extended Self-test Log size 3449 not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Vendor (0xff) Completed without error 00% 11002 - # 2 Vendor (0xff) Completed without error 00% 10995 - # 3 Vendor (0xff) Completed without error 00% 10649 - # 4 Vendor (0xff) Completed without error 00% 9581 - # 5 Vendor (0xff) Completed without error 00% 8869 - # 6 Vendor (0xff) Completed without error 00% 8656 - # 7 Vendor (0xff) Completed without error 00% 7281 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: --/ 0 Celsius Lifetime Min/Max Temperature: --/ 0 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: -5/75 Celsius Temperature History Size (Index): 478 (78) Index Estimated Time Temperature Celsius 79 2023-01-05 14:10 ? - ... ..(473 skipped). .. - 75 2023-01-08 21:10 ? - 76 2023-01-08 21:20 0 - 77 2023-01-08 21:30 0 - 78 2023-01-08 21:40 0 - SCT Error Recovery Control: Read: 40 (4.0 seconds) Write: 40 (4.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 6767 --- Lifetime Power-On Resets 0x01 0x010 4 11667 --- Power-on Hours 0x01 0x018 6 28099159420 --- Logical Sectors Written 0x01 0x020 6 358030146 --- Number of Write Commands 0x01 0x028 6 30753686108 --- Logical Sectors Read 0x01 0x030 6 452518052 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 0 --- Current Temperature 0x05 0x010 1 0 --- Average Short Term Temperature 0x05 0x018 1 0 --- Average Long Term Temperature 0x05 0x020 1 0 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 0 --- Highest Average Short Term Temperature 0x05 0x038 1 0 --- Lowest Average Short Term Temperature 0x05 0x040 1 0 --- Highest Average Long Term Temperature 0x05 0x048 1 0 --- Lowest Average Long Term Temperature 0x05 0x050 4 - --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 - --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 474 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 47 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 6 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 6 Device-to-host register FISes sent due to a COMRESET /dev/sdd smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron Client SSDs Device Model: Crucial_CT275MX300SSD1 Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: M0CR021 User Capacity: 275,064,201,216 bytes [275 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jan 8 21:47:47 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 728) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 5) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x0035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 0 5 Reallocate_NAND_Blk_Cnt -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 7392 12 Power_Cycle_Count -O--CK 100 100 000 - 4000 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Ave_Block-Erase_Count -O--CK 096 096 000 - 70 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 908 183 SATA_Interfac_Downshift -O--CK 100 100 000 - 0 184 Error_Correction_Count -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 075 059 000 - 25 (Min/Max 13/41) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_ECC_Cnt -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 1 202 Percent_Lifetime_Remain ----CK 096 096 001 - 4 206 Write_Error_Rate -OSR-- 100 100 000 - 0 246 Total_LBAs_Written -O--CK 100 100 000 - 17845009345 247 Host_Program_Page_Count -O--CK 100 100 000 - 558699759 248 FTL_Program_Page_Count -O--CK 100 100 000 - 211618758 180 Unused_Reserve_NAND_Blk PO--CK 000 000 000 - 1260 210 Success_RAIN_Recov_Cnt -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 16383 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x24 GPL R/O 8000 Current Device Internal Status Data log 0x25 GPL R/O 8000 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL VS 35328 Device vendor specific log 0xa1 GPL,SL VS 3 Device vendor specific log 0xa2 GPL,SL VS 1 Device vendor specific log 0xa3 GPL VS 13824 Device vendor specific log 0xa4 GPL VS 354 Device vendor specific log 0xa4 SL VS 98 Device vendor specific log 0xa5 GPL VS 8000 Device vendor specific log 0xa5 SL VS 64 Device vendor specific log 0xa6 GPL VS 8000 Device vendor specific log 0xa6 SL VS 64 Device vendor specific log 0xa7-0xdf GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (16383 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 7239 - # 2 Offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 18/27 Celsius Lifetime Min/Max Temperature: 13/41 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: -5/75 Celsius Temperature History Size (Index): 478 (287) Index Estimated Time Temperature Celsius 288 2023-01-08 13:50 0 - ... ..( 20 skipped). .. - 309 2023-01-08 14:11 0 - 310 2023-01-08 14:12 24 ***** 311 2023-01-08 14:13 24 ***** 312 2023-01-08 14:14 25 ****** 313 2023-01-08 14:15 27 ******** 314 2023-01-08 14:16 25 ****** 315 2023-01-08 14:17 0 - ... ..(103 skipped). .. - 419 2023-01-08 16:01 0 - 420 2023-01-08 16:02 ? - 421 2023-01-08 16:03 20 * 422 2023-01-08 16:04 21 ** 423 2023-01-08 16:05 22 *** 424 2023-01-08 16:06 23 **** ... ..( 4 skipped). .. **** 429 2023-01-08 16:11 23 **** 430 2023-01-08 16:12 24 ***** ... ..( 6 skipped). .. ***** 437 2023-01-08 16:19 24 ***** 438 2023-01-08 16:20 25 ****** 439 2023-01-08 16:21 25 ****** 440 2023-01-08 16:22 24 ***** 441 2023-01-08 16:23 24 ***** 442 2023-01-08 16:24 25 ****** ... ..( 3 skipped). .. ****** 446 2023-01-08 16:28 25 ****** 447 2023-01-08 16:29 26 ******* 448 2023-01-08 16:30 26 ******* 449 2023-01-08 16:31 25 ****** ... ..( 2 skipped). .. ****** 452 2023-01-08 16:34 25 ****** 453 2023-01-08 16:35 26 ******* 454 2023-01-08 16:36 26 ******* 455 2023-01-08 16:37 26 ******* 456 2023-01-08 16:38 25 ****** 457 2023-01-08 16:39 26 ******* 458 2023-01-08 16:40 26 ******* 459 2023-01-08 16:41 26 ******* 460 2023-01-08 16:42 27 ******** 461 2023-01-08 16:43 27 ******** 462 2023-01-08 16:44 26 ******* ... ..( 6 skipped). .. ******* 469 2023-01-08 16:51 26 ******* 470 2023-01-08 16:52 25 ****** ... ..( 6 skipped). .. ****** 477 2023-01-08 16:59 25 ****** 0 2023-01-08 17:00 0 - ... ..(286 skipped). .. - 287 2023-01-08 21:47 0 - SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 4000 --- Lifetime Power-On Resets 0x01 0x010 4 7392 --- Power-on Hours 0x01 0x018 6 17845009345 --- Logical Sectors Written 0x01 0x020 6 239510809 --- Number of Write Commands 0x01 0x028 6 13145725980 --- Logical Sectors Read 0x01 0x030 6 188311038 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 7362 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 25 --- Current Temperature 0x05 0x010 1 0 --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 41 --- Highest Temperature 0x05 0x028 1 13 --- Lowest Temperature 0x05 0x030 1 32 --- Highest Average Short Term Temperature 0x05 0x038 1 - --- Lowest Average Short Term Temperature 0x05 0x040 1 23 --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 21997 --- Number of Hardware Resets 0x06 0x010 4 12013 --- Number of ASR Events 0x06 0x018 4 1 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 4 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 8 Device-to-host register FISes sent due to a COMRESET /dev/sde smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.1-desktop-1omv2290] (OpenMandriva Lx 7.3-2) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD30EZRZ-00WN9B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jan 8 21:47:47 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (43080) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 432) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 175 173 021 - 8216 4 Start_Stop_Count -O--CK 094 094 000 - 6576 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 089 089 000 - 8078 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4957 192 Power-Off_Retract_Count -O--CK 198 198 000 - 1705 193 Load_Cycle_Count -O--CK 187 187 000 - 40446 194 Temperature_Celsius -O---K 124 113 000 - 28 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 39 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 7923 - # 2 Short offline Completed without error 00% 4502 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 20/28 Celsius Lifetime Min/Max Temperature: 3/39 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (34) Index Estimated Time Temperature Celsius 35 2023-01-08 13:50 29 ********** ... ..( 90 skipped). .. ********** 126 2023-01-08 15:21 29 ********** 127 2023-01-08 15:22 30 *********** ... ..( 48 skipped). .. *********** 176 2023-01-08 16:11 30 *********** 177 2023-01-08 16:12 29 ********** ... ..(108 skipped). .. ********** 286 2023-01-08 18:01 29 ********** 287 2023-01-08 18:02 ? - 288 2023-01-08 18:03 20 * ... ..( 2 skipped). .. * 291 2023-01-08 18:06 20 * 292 2023-01-08 18:07 21 ** 293 2023-01-08 18:08 22 *** ... ..( 2 skipped). .. *** 296 2023-01-08 18:11 22 *** 297 2023-01-08 18:12 23 **** 298 2023-01-08 18:13 23 **** 299 2023-01-08 18:14 24 ***** 300 2023-01-08 18:15 24 ***** 301 2023-01-08 18:16 25 ****** ... ..( 2 skipped). .. ****** 304 2023-01-08 18:19 25 ****** 305 2023-01-08 18:20 26 ******* 306 2023-01-08 18:21 26 ******* 307 2023-01-08 18:22 26 ******* 308 2023-01-08 18:23 27 ******** ... ..( 2 skipped). .. ******** 311 2023-01-08 18:26 27 ******** 312 2023-01-08 18:27 28 ********* ... ..( 8 skipped). .. ********* 321 2023-01-08 18:36 28 ********* 322 2023-01-08 18:37 29 ********** ... ..( 4 skipped). .. ********** 327 2023-01-08 18:42 29 ********** 328 2023-01-08 18:43 ? - 329 2023-01-08 18:44 20 * 330 2023-01-08 18:45 21 ** 331 2023-01-08 18:46 21 ** 332 2023-01-08 18:47 22 *** 333 2023-01-08 18:48 23 **** ... ..( 3 skipped). .. **** 337 2023-01-08 18:52 23 **** 338 2023-01-08 18:53 24 ***** 339 2023-01-08 18:54 24 ***** 340 2023-01-08 18:55 25 ****** ... ..( 2 skipped). .. ****** 343 2023-01-08 18:58 25 ****** 344 2023-01-08 18:59 26 ******* ... ..( 8 skipped). .. ******* 353 2023-01-08 19:08 26 ******* 354 2023-01-08 19:09 27 ******** ... ..( 10 skipped). .. ******** 365 2023-01-08 19:20 27 ******** 366 2023-01-08 19:21 28 ********* ... ..( 17 skipped). .. ********* 384 2023-01-08 19:39 28 ********* 385 2023-01-08 19:40 27 ******** 386 2023-01-08 19:41 27 ******** 387 2023-01-08 19:42 27 ******** 388 2023-01-08 19:43 28 ********* ... ..( 83 skipped). .. ********* 472 2023-01-08 21:07 28 ********* 473 2023-01-08 21:08 29 ********** ... ..( 38 skipped). .. ********** 34 2023-01-08 21:47 29 ********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 3455 Vendor specific