/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.3.0-42-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus Device Model: ST3160023AS Serial Number: -- Firmware Version: 3.43 User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA/ATAPI-6 T13/1410D revision 2 Local Time is: Sun Mar 22 03:36:20 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 423) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 69) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 062 048 006 - 51880268 3 Spin_Up_Time -O---- 096 096 000 - 0 4 Start_Stop_Count PO--CK 098 098 020 - 2550 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 085 060 030 - 356173391 9 Power_On_Hours -O--CK 095 095 000 - 4646 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count PO--CK 098 098 020 - 2602 194 Temperature_Celsius -O---K 038 042 000 - 38 (0 5 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 062 048 000 - 51880268 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23552 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 913 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 913 [12] occurred at disk power-on lifetime: 2347 hours (97 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 00 00 00 00 e0 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 40 00 00 00 04 00 00 f8 00 63 fb e0 00 00:05:03.803 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:03.792 READ DMA 40 00 00 00 04 00 00 f8 00 63 f7 e0 00 00:05:03.782 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:00.304 READ DMA 40 00 00 00 08 00 00 f8 00 63 f7 e0 00 00:05:00.294 READ VERIFY SECTOR(S) Error 912 [11] occurred at disk power-on lifetime: 2444 hours (101 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 02 42 00 00 f8 fd 63 fd e0 00 Error: UNC at LBA = 0xf8fd63fd = 4177355773 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 02 00 00 00 f8 00 63 3f e0 00 10:43:48.504 READ VERIFY SECTOR(S) EXT 42 00 00 02 00 00 00 f6 00 63 3f e0 00 10:43:48.569 READ VERIFY SECTOR(S) EXT 42 00 00 02 00 00 00 f4 00 63 3f e0 00 10:43:48.564 READ VERIFY SECTOR(S) EXT 42 00 00 02 00 00 00 f2 00 63 3f e0 00 10:43:48.560 READ VERIFY SECTOR(S) EXT 42 00 00 02 00 00 00 f0 00 63 3f e0 00 10:43:48.555 READ VERIFY SECTOR(S) EXT Error 911 [10] occurred at disk power-on lifetime: 2347 hours (97 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 40 00 00 00 01 00 00 f8 00 63 fd e0 00 00:05:03.803 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:03.792 READ DMA 40 00 00 00 02 00 00 f8 00 63 fd e0 00 00:05:17.838 READ VERIFY SECTOR(S) 40 00 00 00 02 00 00 f8 00 63 fb e0 00 00:05:17.819 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:14.350 READ DMA Error 910 [9] occurred at disk power-on lifetime: 2347 hours (97 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 00 00 00 00 e0 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 40 00 00 00 02 00 00 f8 00 63 fd e0 00 00:05:03.803 READ VERIFY SECTOR(S) 40 00 00 00 02 00 00 f8 00 63 fb e0 00 00:05:03.792 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:03.782 READ DMA 40 00 00 00 04 00 00 f8 00 63 fb e0 00 00:05:00.304 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:14.350 READ DMA Error 909 [8] occurred at disk power-on lifetime: 2347 hours (97 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 00 00 00 00 e0 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 40 00 00 00 04 00 00 f8 00 63 fb e0 00 00:05:03.803 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:03.792 READ DMA 40 00 00 00 04 00 00 f8 00 63 f7 e0 00 00:05:03.782 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:00.304 READ DMA 40 00 00 00 08 00 00 f8 00 63 f7 e0 00 00:05:00.294 READ VERIFY SECTOR(S) Error 908 [7] occurred at disk power-on lifetime: 2444 hours (101 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 02 42 00 00 f8 fd 63 fd e0 00 Error: UNC at LBA = 0xf8fd63fd = 4177355773 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 02 00 00 00 f8 00 63 3f e0 00 10:43:48.504 READ VERIFY SECTOR(S) EXT 42 00 00 02 00 00 00 f6 00 63 3f e0 00 10:43:48.569 READ VERIFY SECTOR(S) EXT 42 00 00 02 00 00 00 f4 00 63 3f e0 00 10:43:48.564 READ VERIFY SECTOR(S) EXT 42 00 00 02 00 00 00 f2 00 63 3f e0 00 10:43:48.560 READ VERIFY SECTOR(S) EXT 42 00 00 02 00 00 00 f0 00 63 3f e0 00 10:43:48.555 READ VERIFY SECTOR(S) EXT Error 907 [6] occurred at disk power-on lifetime: 2347 hours (97 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 40 00 00 00 01 00 00 f8 00 63 fd e0 00 00:05:03.803 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:03.792 READ DMA 40 00 00 00 02 00 00 f8 00 63 fd e0 00 00:05:17.838 READ VERIFY SECTOR(S) 40 00 00 00 02 00 00 f8 00 63 fb e0 00 00:05:17.819 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:14.350 READ DMA Error 906 [5] occurred at disk power-on lifetime: 2347 hours (97 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 00 00 00 00 e0 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 40 00 00 00 02 00 00 f8 00 63 fd e0 00 00:05:03.803 READ VERIFY SECTOR(S) 40 00 00 00 02 00 00 f8 00 63 fb e0 00 00:05:03.792 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:03.782 READ DMA 40 00 00 00 04 00 00 f8 00 63 fb e0 00 00:05:00.304 READ VERIFY SECTOR(S) c8 00 00 00 01 00 00 00 00 00 00 e0 00 00:05:14.350 READ DMA SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 1 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported