Probe #81179cf1b2 of Samsung 300E4C

Log: smartctl

/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar 5K750 Device Model: Hitachi HTS547550A9E384 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JE3OA50A User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Jan 19 23:35:06 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 151) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 197 197 040 - 163 3 Spin_Up_Time POS--- 173 173 033 - 1 4 Start_Stop_Count -O--C- 096 096 000 - 7417 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 115 115 040 - 34 9 Power_On_Hours -O--C- 078 078 000 - 9873 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 6851 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 65536 192 Power-Off_Retract_Count -O--CK 099 099 000 - 391 193 Load_Cycle_Count -O--C- 075 075 000 - 250743 194 Temperature_Celsius -O---- 142 142 000 - 42 (Min/Max 9/71) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 19 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 19 [2] occurred at disk power-on lifetime: 8584 hours (357 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 3a 3b c0 00 00 Error: WP at LBA = 0x003a3bc0 = 3816384 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 18 00 88 00 00 00 5f 10 50 40 00 01:16:34.886 WRITE FPDMA QUEUED 60 00 20 00 80 00 00 08 82 e5 80 40 00 01:16:33.126 READ FPDMA QUEUED 61 00 08 00 78 00 00 08 82 e3 40 40 00 01:16:33.125 WRITE FPDMA QUEUED 61 00 08 00 70 00 00 08 82 d4 10 40 00 01:16:33.125 WRITE FPDMA QUEUED 61 00 08 00 68 00 00 08 82 d3 e8 40 00 01:16:33.125 WRITE FPDMA QUEUED Error 18 [1] occurred at disk power-on lifetime: 8584 hours (357 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 3a 3b c0 00 00 Error: WP at LBA = 0x003a3bc0 = 3816384 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 f8 00 00 00 63 10 20 40 00 01:16:31.386 WRITE FPDMA QUEUED 60 00 20 00 f0 00 00 08 82 d3 40 40 00 01:16:29.849 READ FPDMA QUEUED 61 00 08 00 e8 00 00 08 82 bf b8 40 00 01:16:29.848 WRITE FPDMA QUEUED 61 00 20 00 e0 00 00 11 49 f3 40 40 00 01:16:29.765 WRITE FPDMA QUEUED 60 01 00 00 d8 00 00 00 3a 3b c0 40 00 01:16:29.762 READ FPDMA QUEUED Error 17 [0] occurred at disk power-on lifetime: 8584 hours (357 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 3a 3b c0 00 00 Error: WP at LBA = 0x003a3bc0 = 3816384 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 18 00 00 0a 50 f0 e0 40 00 01:16:28.987 WRITE FPDMA QUEUED 61 01 00 00 10 00 00 0a 50 ef e0 40 00 01:16:28.987 WRITE FPDMA QUEUED 61 01 00 00 08 00 00 0a 50 ee e0 40 00 01:16:28.987 WRITE FPDMA QUEUED 61 01 00 00 00 00 00 0a 50 ed e0 40 00 01:16:28.987 WRITE FPDMA QUEUED 61 01 00 00 f8 00 00 0a 50 ec e0 40 00 01:16:28.987 WRITE FPDMA QUEUED Error 16 [3] occurred at disk power-on lifetime: 8584 hours (357 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 3a 3a c0 00 00 Error: WP at LBA = 0x003a3ac0 = 3816128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 01 00 58 00 00 00 0b 55 f8 40 00 01:16:26.171 WRITE FPDMA QUEUED 61 01 00 00 50 00 00 0a 50 e8 e0 40 00 01:16:25.987 WRITE FPDMA QUEUED 61 01 00 00 48 00 00 0a 50 e7 e0 40 00 01:16:25.987 WRITE FPDMA QUEUED 61 01 00 00 40 00 00 0a 50 e6 e0 40 00 01:16:25.987 WRITE FPDMA QUEUED 61 01 00 00 38 00 00 0a 50 e5 e0 40 00 01:16:25.987 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 9841 - # 2 Extended offline Completed without error 00% 9665 - # 3 Extended offline Completed without error 00% 9505 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 43 Celsius Power Cycle Min/Max Temperature: 41/44 Celsius Lifetime Min/Max Temperature: 9/71 Celsius Lifetime Average Temperature: 42 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (23) Index Estimated Time Temperature Celsius 24 2018-01-19 21:28 43 ************************ 25 2018-01-19 21:29 43 ************************ 26 2018-01-19 21:30 44 ************************* 27 2018-01-19 21:31 43 ************************ 28 2018-01-19 21:32 43 ************************ 29 2018-01-19 21:33 44 ************************* 30 2018-01-19 21:34 43 ************************ 31 2018-01-19 21:35 43 ************************ 32 2018-01-19 21:36 43 ************************ 33 2018-01-19 21:37 44 ************************* ... ..( 25 skipped). .. ************************* 59 2018-01-19 22:03 44 ************************* 60 2018-01-19 22:04 45 ************************** 61 2018-01-19 22:05 45 ************************** 62 2018-01-19 22:06 44 ************************* ... ..( 5 skipped). .. ************************* 68 2018-01-19 22:12 44 ************************* 69 2018-01-19 22:13 45 ************************** 70 2018-01-19 22:14 45 ************************** 71 2018-01-19 22:15 45 ************************** 72 2018-01-19 22:16 44 ************************* 73 2018-01-19 22:17 45 ************************** ... ..( 2 skipped). .. ************************** 76 2018-01-19 22:20 45 ************************** 77 2018-01-19 22:21 44 ************************* 78 2018-01-19 22:22 45 ************************** 79 2018-01-19 22:23 44 ************************* ... ..( 19 skipped). .. ************************* 99 2018-01-19 22:43 44 ************************* 100 2018-01-19 22:44 43 ************************ 101 2018-01-19 22:45 44 ************************* 102 2018-01-19 22:46 43 ************************ 103 2018-01-19 22:47 43 ************************ 104 2018-01-19 22:48 ? - 105 2018-01-19 22:49 43 ************************ ... ..( 4 skipped). .. ************************ 110 2018-01-19 22:54 43 ************************ 111 2018-01-19 22:55 44 ************************* ... ..( 11 skipped). .. ************************* 123 2018-01-19 23:07 44 ************************* 124 2018-01-19 23:08 43 ************************ ... ..( 6 skipped). .. ************************ 3 2018-01-19 23:15 43 ************************ 4 2018-01-19 23:16 42 *********************** ... ..( 4 skipped). .. *********************** 9 2018-01-19 23:21 42 *********************** 10 2018-01-19 23:22 41 ********************** 11 2018-01-19 23:23 42 *********************** ... ..( 5 skipped). .. *********************** 17 2018-01-19 23:29 42 *********************** 18 2018-01-19 23:30 43 ************************ ... ..( 4 skipped). .. ************************ 23 2018-01-19 23:35 43 ************************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 6851 --- Lifetime Power-On Resets 0x01 0x010 4 9873 --- Power-on Hours 0x01 0x018 6 18653105650 --- Logical Sectors Written 0x01 0x020 6 278359328 --- Number of Write Commands 0x01 0x028 6 25131198223 --- Logical Sectors Read 0x01 0x030 6 373806946 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 9112 --- Spindle Motor Power-on Hours 0x03 0x010 4 9094 --- Head Flying Hours 0x03 0x018 4 250743 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 1174 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 7702 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 43 --- Current Temperature 0x05 0x010 1 43 N-- Average Short Term Temperature 0x05 0x018 1 46 N-- Average Long Term Temperature 0x05 0x020 1 71 --- Highest Temperature 0x05 0x028 1 9 --- Lowest Temperature 0x05 0x030 1 57 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 51 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 2430 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 6409 --- Number of Hardware Resets 0x06 0x010 4 7058 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 29646 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS


Hardware for Linux and BSD

GitHub