/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.12.10-76061203-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z5K500 Device Model: HGST HTS545050A7E680 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GR2OA350 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jun 16 04:11:39 2025 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 110) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 062 - 0 2 Throughput_Performance P-S--K 100 100 040 - 0 3 Spin_Up_Time PO---K 245 100 033 - 1 4 Start_Stop_Count -O--CK 099 099 000 - 1592 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate POSR-K 100 100 067 - 0 8 Seek_Time_Performance P-S--K 100 100 040 - 0 9 Power_On_Hours -O--CK 098 098 000 - 1052 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 1365 183 Runtime_Bad_Block -O--CK 100 100 001 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 180397342720 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 064 053 045 - 36 (Min/Max 33/36) 191 G-Sense_Error_Rate -O--CK 098 098 000 - 571 192 Power-Off_Retract_Count -O--CK 100 100 000 - 2359332 193 Load_Cycle_Count -O--CK 097 097 000 - 39746 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0 223 Load_Retry_Count -O-R-K 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 33/36 Celsius Lifetime Min/Max Temperature: 8/47 Celsius Specified Max Operating Temperature: 32 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (55) Index Estimated Time Temperature Celsius 56 2025-06-16 02:04 47 **************************** 57 2025-06-16 02:05 47 **************************** 58 2025-06-16 02:06 46 *************************** 59 2025-06-16 02:07 ? - 60 2025-06-16 02:08 ? - 61 2025-06-16 02:09 37 ****************** 62 2025-06-16 02:10 ? - 63 2025-06-16 02:11 38 ******************* 64 2025-06-16 02:12 39 ******************** ... ..( 14 skipped). .. ******************** 79 2025-06-16 02:27 39 ******************** 80 2025-06-16 02:28 40 ********************* 81 2025-06-16 02:29 ? - ... ..( 2 skipped). .. - 84 2025-06-16 02:32 ? - 85 2025-06-16 02:33 38 ******************* 86 2025-06-16 02:34 ? - 87 2025-06-16 02:35 37 ****************** 88 2025-06-16 02:36 ? - 89 2025-06-16 02:37 38 ******************* 90 2025-06-16 02:38 ? - 91 2025-06-16 02:39 38 ******************* ... ..( 2 skipped). .. ******************* 94 2025-06-16 02:42 38 ******************* 95 2025-06-16 02:43 39 ******************** 96 2025-06-16 02:44 39 ******************** 97 2025-06-16 02:45 38 ******************* 98 2025-06-16 02:46 ? - 99 2025-06-16 02:47 35 **************** 100 2025-06-16 02:48 36 ***************** ... ..( 3 skipped). .. ***************** 104 2025-06-16 02:52 36 ***************** 105 2025-06-16 02:53 37 ****************** ... ..( 4 skipped). .. ****************** 110 2025-06-16 02:58 37 ****************** 111 2025-06-16 02:59 38 ******************* ... ..( 6 skipped). .. ******************* 118 2025-06-16 03:06 38 ******************* 119 2025-06-16 03:07 39 ******************** ... ..( 28 skipped). .. ******************** 20 2025-06-16 03:36 39 ******************** 21 2025-06-16 03:37 ? - 22 2025-06-16 03:38 39 ******************** 23 2025-06-16 03:39 38 ******************* 24 2025-06-16 03:40 39 ******************** 25 2025-06-16 03:41 38 ******************* 26 2025-06-16 03:42 39 ******************** ... ..( 5 skipped). .. ******************** 32 2025-06-16 03:48 39 ******************** 33 2025-06-16 03:49 40 ********************* 34 2025-06-16 03:50 39 ******************** 35 2025-06-16 03:51 ? - 36 2025-06-16 03:52 ? - 37 2025-06-16 03:53 33 ************** 38 2025-06-16 03:54 34 *************** ... ..( 2 skipped). .. *************** 41 2025-06-16 03:57 34 *************** 42 2025-06-16 03:58 35 **************** ... ..( 4 skipped). .. **************** 47 2025-06-16 04:03 35 **************** 48 2025-06-16 04:04 36 ***************** ... ..( 6 skipped). .. ***************** 55 2025-06-16 04:11 36 ***************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 37 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS