/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.14-desktop-1omv4002] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD2500BEVS-22UST0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) Local Time is: Sun Feb 13 10:15:21 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9180) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 110) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 2745 3 Spin_Up_Time PO---- 193 184 021 - 1308 4 Start_Stop_Count -O--CK 089 089 000 - 11618 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-- 100 253 051 - 0 9 Power_On_Hours -O--CK 086 086 000 - 10783 10 Spin_Retry_Count PO--C- 100 099 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 090 090 000 - 10584 192 Power-Off_Retract_Count -O--CK 200 200 000 - 302 193 Load_Cycle_Count -O--CK 137 137 000 - 191837 194 Temperature_Celsius -O---K 123 094 000 - 24 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 4 198 Offline_Uncorrectable ----C- 100 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 12 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2442 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2442 [17] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 ef 60 02 22 00 00 00 00 00 00 00 0e 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 02 10 00 00 02 ef 00 22 ef 00 00 08 00:00:04.224 DEVICE RESET 00 ee ec 02 22 00 00 08 00 00 00 00 00 00:02:20.015 NOP [Reserved subcommand] [OBS-ACS-2] 08 46 03 00 00 02 ee 00 22 ef 00 00 08 00:00:00.000 DEVICE RESET Error 2441 [16] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 55 60 02 13 00 00 00 00 00 00 00 0e 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 50 08 00 10 02 55 0e 13 60 00 00 08 00:00:02.136 DEVICE RESET 00 55 27 02 13 00 02 08 00 10 00 00 00 00:02:16.021 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 00 00 00 02 54 00 13 ec 00 00 08 00:00:00.000 DEVICE RESET Error 2440 [15] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 b9 60 02 03 00 00 00 00 00 00 00 0e 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 20 08 00 08 02 b9 0e 03 60 00 00 08 00:00:04.136 DEVICE RESET 0e b8 ef 02 03 00 18 08 00 08 00 00 00 00:02:12.025 [RESERVED] 08 00 00 00 00 02 b8 00 03 27 00 00 08 00:00:00.002 DEVICE RESET Error 2439 [14] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 20 60 01 f4 00 00 00 00 00 00 00 0e 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 e0 08 00 08 01 20 0e f4 60 00 00 08 00:00:00.232 DEVICE RESET 0e 20 60 01 f4 00 d8 08 10 08 00 00 0e 00:02:08.032 [RESERVED] 08 02 10 00 00 01 1f 00 f4 ef 00 00 08 00:01:03.696 DEVICE RESET Error 2438 [13] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 84 60 01 e4 00 00 00 00 00 00 00 0e 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 a0 08 00 f0 01 84 0e e4 60 00 00 08 00:01:03.656 DEVICE RESET 0e 84 60 01 e4 00 98 08 10 08 00 00 0e 00:02:04.036 [RESERVED] 08 88 08 00 00 01 84 0e e4 60 00 00 08 00:00:02.192 DEVICE RESET Error 2437 [12] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 eb 60 01 d4 00 00 00 00 00 00 00 0e 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 58 08 00 08 01 eb 0e d4 60 00 00 08 00:00:00.096 DEVICE RESET 0e eb 60 01 d4 00 50 08 10 08 00 00 0e 00:02:00.043 [RESERVED] 08 40 08 00 f0 01 eb 0e d4 60 00 00 08 00:00:59.464 DEVICE RESET Error 2436 [11] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 53 60 01 c5 00 00 00 00 00 00 00 0e 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 08 08 00 08 01 53 0e c5 60 00 00 08 00:00:04.112 DEVICE RESET 0e 52 60 01 c5 00 00 08 00 08 00 00 0e 00:01:56.050 [RESERVED] 08 e8 08 00 f0 01 52 0e c5 60 00 00 08 00:01:03.728 DEVICE RESET Error 2435 [10] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 31 60 01 b5 00 00 00 00 00 00 00 0e 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 a8 08 00 e0 01 31 0e b5 60 00 00 08 00:00:55.472 DEVICE RESET 0e 31 60 01 b5 00 a0 08 e8 08 00 00 0e 00:01:51.921 [RESERVED] 08 90 08 00 f8 01 31 0e b5 60 00 00 08 00:01:01.592 DEVICE RESET SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 23 Celsius Power Cycle Min/Max Temperature: 17/23 Celsius Lifetime Min/Max Temperature: 17/53 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (78) Index Estimated Time Temperature Celsius 79 2022-02-13 08:08 46 *************************** ... ..( 31 skipped). .. *************************** 111 2022-02-13 08:40 46 *************************** 112 2022-02-13 08:41 47 **************************** ... ..( 14 skipped). .. **************************** 127 2022-02-13 08:56 47 **************************** 0 2022-02-13 08:57 ? - 1 2022-02-13 08:58 24 ***** 2 2022-02-13 08:59 ? - 3 2022-02-13 09:00 25 ****** 4 2022-02-13 09:01 ? - 5 2022-02-13 09:02 25 ****** 6 2022-02-13 09:03 ? - 7 2022-02-13 09:04 23 **** 8 2022-02-13 09:05 24 ***** 9 2022-02-13 09:06 26 ******* 10 2022-02-13 09:07 27 ******** 11 2022-02-13 09:08 28 ********* 12 2022-02-13 09:09 29 ********** 13 2022-02-13 09:10 30 *********** 14 2022-02-13 09:11 32 ************* 15 2022-02-13 09:12 33 ************** 16 2022-02-13 09:13 33 ************** 17 2022-02-13 09:14 34 *************** 18 2022-02-13 09:15 34 *************** 19 2022-02-13 09:16 35 **************** 20 2022-02-13 09:17 35 **************** 21 2022-02-13 09:18 35 **************** 22 2022-02-13 09:19 36 ***************** 23 2022-02-13 09:20 36 ***************** 24 2022-02-13 09:21 37 ****************** ... ..( 2 skipped). .. ****************** 27 2022-02-13 09:24 37 ****************** 28 2022-02-13 09:25 38 ******************* 29 2022-02-13 09:26 38 ******************* 30 2022-02-13 09:27 38 ******************* 31 2022-02-13 09:28 39 ******************** ... ..( 3 skipped). .. ******************** 35 2022-02-13 09:32 39 ******************** 36 2022-02-13 09:33 40 ********************* ... ..( 2 skipped). .. ********************* 39 2022-02-13 09:36 40 ********************* 40 2022-02-13 09:37 41 ********************** ... ..( 20 skipped). .. ********************** 61 2022-02-13 09:58 41 ********************** 62 2022-02-13 09:59 ? - 63 2022-02-13 10:00 24 ***** 64 2022-02-13 10:01 ? - 65 2022-02-13 10:02 24 ***** 66 2022-02-13 10:03 ? - 67 2022-02-13 10:04 24 ***** 68 2022-02-13 10:05 ? - 69 2022-02-13 10:06 17 - 70 2022-02-13 10:07 17 - 71 2022-02-13 10:08 19 - 72 2022-02-13 10:09 20 * 73 2022-02-13 10:10 21 ** 74 2022-02-13 10:11 21 ** 75 2022-02-13 10:12 22 *** 76 2022-02-13 10:13 23 **** 77 2022-02-13 10:14 23 **** 78 2022-02-13 10:15 46 *************************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x8000 4 550 Vendor specific