/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-66-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Marvell based SanDisk SSDs Device Model: SanDisk SSD PLUS 240GB Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: UF4004RL User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Mar 11 11:59:06 2021 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 41) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 1045 12 Power_Cycle_Count -O--CK 100 100 000 - 1472 165 Total_Write/Erase_Count -O--CK 100 100 000 - 863 166 Min_W/E_Cycle -O--CK 100 100 --- - 5 167 Min_Bad_Block/Die -O--CK 100 100 --- - 45 168 Maximum_Erase_Cycle -O--CK 100 100 --- - 18 169 Total_Bad_Block -O--CK 100 100 --- - 300 170 Unknown_Attribute -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Avg_Write/Erase_Count -O--CK 100 100 000 - 5 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 1107 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 074 044 000 - 26 (Min/Max 0/44) 199 SATA_CRC_Error -O--CK 100 100 --- - 0 230 Perc_Write/Erase_Count -O--CK 100 100 000 - 558 256 558 232 Perc_Avail_Resrvd_Space PO--CK 100 100 005 - 100 233 Total_NAND_Writes_GiB -O--CK 100 100 --- - 1341 234 Perc_Write/Erase_Ct_BC -O--CK 100 100 000 - 6874 241 Total_Writes_GiB ----CK 100 100 000 - 2207 242 Total_Reads_GiB ----CK 100 100 000 - 1013 244 Thermal_Throttle -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3-0xa4 GPL,SL VS 1 Device vendor specific log 0xa7 GPL,SL VS 1 Device vendor specific log 0xa9 GPL,SL VS 4 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1472 --- Lifetime Power-On Resets 0x01 0x010 4 1045 --- Power-on Hours 0x01 0x018 6 4629083813 --- Logical Sectors Written 0x01 0x028 6 2124963869 --- Logical Sectors Read 0x01 0x038 6 1045 --- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 26 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 43 --- Highest Temperature 0x05 0x028 1 13 --- Lowest Temperature 0x05 0x030 1 34 --- Highest Average Short Term Temperature 0x05 0x038 1 34 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 13640 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-66-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST500LM012 HN-M500MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2BA30001 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Mar 11 11:59:06 2021 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6480) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 108) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 3 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 093 090 025 - 2132 4 Start_Stop_Count -O--CK 092 092 000 - 8636 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 15509 10 Spin_Retry_Count -O--CK 252 252 051 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3445 191 G-Sense_Error_Rate -O---K 100 100 000 - 151 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 058 000 - 25 (Min/Max 4/57) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 2069 223 Load_Retry_Count -O--CK 100 100 000 - 52 225 Load_Cycle_Count -O--CK 084 084 000 - 165912 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 19/25 Celsius Lifetime Min/Max Temperature: 5/58 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (100) Index Estimated Time Temperature Celsius 101 2021-03-11 01:20 25 ****** 102 2021-03-11 01:25 27 ******** 103 2021-03-11 01:30 28 ********* ... ..( 9 skipped). .. ********* 113 2021-03-11 02:20 28 ********* 114 2021-03-11 02:25 27 ******** ... ..( 13 skipped). .. ******** 0 2021-03-11 03:35 27 ******** 1 2021-03-11 03:40 22 *** 2 2021-03-11 03:45 23 **** 3 2021-03-11 03:50 24 ***** 4 2021-03-11 03:55 24 ***** 5 2021-03-11 04:00 24 ***** 6 2021-03-11 04:05 25 ****** ... ..( 5 skipped). .. ****** 12 2021-03-11 04:35 25 ****** 13 2021-03-11 04:40 26 ******* ... ..( 17 skipped). .. ******* 31 2021-03-11 06:10 26 ******* 32 2021-03-11 06:15 27 ******** 33 2021-03-11 06:20 27 ******** 34 2021-03-11 06:25 27 ******** 35 2021-03-11 06:30 28 ********* ... ..( 9 skipped). .. ********* 45 2021-03-11 07:20 28 ********* 46 2021-03-11 07:25 27 ******** 47 2021-03-11 07:30 28 ********* ... ..( 7 skipped). .. ********* 55 2021-03-11 08:10 28 ********* 56 2021-03-11 08:15 27 ******** ... ..( 19 skipped). .. ******** 76 2021-03-11 09:55 27 ******** 77 2021-03-11 10:00 26 ******* 78 2021-03-11 10:05 21 ** 79 2021-03-11 10:10 22 *** 80 2021-03-11 10:15 23 **** 81 2021-03-11 10:20 24 ***** ... ..( 4 skipped). .. ***** 86 2021-03-11 10:45 24 ***** 87 2021-03-11 10:50 25 ****** ... ..( 12 skipped). .. ****** 100 2021-03-11 11:55 25 ****** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 61 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific