/dev/sda smartctl 7.2 2020-12-30 r5155 [aarch64-linux-5.15.0-1035-raspi] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD3200BPVT-22JJ5T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 320,072,933,376 bytes [320 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Aug 28 08:05:53 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7380) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 76) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 154 134 021 - 1266 4 Start_Stop_Count -O--CK 001 001 000 - 154156 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 082 081 000 - 13540 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2301 191 G-Sense_Error_Rate -O--CK 001 001 000 - 225 192 Power-Off_Retract_Count -O--CK 200 200 000 - 523 193 Load_Cycle_Count -O--CK 001 001 000 - 5205405 194 Temperature_Celsius -O---K 107 086 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 37 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 37 [12] occurred at disk power-on lifetime: 1002 hours (41 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.889 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.885 IDENTIFY DEVICE 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.848 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.847 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.846 SET FEATURES [Set transfer mode] Error 36 [11] occurred at disk power-on lifetime: 1002 hours (41 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 04 00 00 00 11 5d 38 00 e0 00 Device Fault; Error: ABRT 1024 sectors at LBA = 0x115d3800 = 291321856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.848 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.847 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.846 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.845 IDENTIFY DEVICE 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.816 WRITE DMA EXT Error 35 [10] occurred at disk power-on lifetime: 1002 hours (41 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.846 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.845 IDENTIFY DEVICE 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.816 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.815 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.814 SET FEATURES [Set transfer mode] Error 34 [9] occurred at disk power-on lifetime: 1002 hours (41 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 04 00 00 00 11 5d 38 00 e0 00 Device Fault; Error: ABRT 1024 sectors at LBA = 0x115d3800 = 291321856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.816 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.815 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.814 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.813 IDENTIFY DEVICE 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.784 WRITE DMA EXT Error 33 [8] occurred at disk power-on lifetime: 1002 hours (41 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.814 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.813 IDENTIFY DEVICE 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.784 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.782 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.782 SET FEATURES [Set transfer mode] Error 32 [7] occurred at disk power-on lifetime: 1002 hours (41 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 04 00 00 00 11 5d 38 00 e0 00 Device Fault; Error: ABRT 1024 sectors at LBA = 0x115d3800 = 291321856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.784 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.782 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.782 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.780 IDENTIFY DEVICE 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.752 WRITE DMA EXT Error 31 [6] occurred at disk power-on lifetime: 1002 hours (41 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.782 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.780 IDENTIFY DEVICE 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.752 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.750 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.750 SET FEATURES [Set transfer mode] Error 30 [5] occurred at disk power-on lifetime: 1002 hours (41 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 04 00 00 00 11 5d 38 00 e0 00 Device Fault; Error: ABRT 1024 sectors at LBA = 0x115d3800 = 291321856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.752 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.750 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:05.750 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:05.748 IDENTIFY DEVICE 35 00 00 04 00 00 00 11 5d 38 00 e0 08 00:00:05.720 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 31/36 Celsius Lifetime Min/Max Temperature: 0/57 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (100) Index Estimated Time Temperature Celsius 101 2023-08-28 05:58 31 ************ 102 2023-08-28 05:59 33 ************** 103 2023-08-28 06:00 32 ************* ... ..( 5 skipped). .. ************* 109 2023-08-28 06:06 32 ************* 110 2023-08-28 06:07 31 ************ 111 2023-08-28 06:08 31 ************ 112 2023-08-28 06:09 ? - 113 2023-08-28 06:10 31 ************ ... ..( 5 skipped). .. ************ 119 2023-08-28 06:16 31 ************ 120 2023-08-28 06:17 ? - 121 2023-08-28 06:18 31 ************ ... ..( 6 skipped). .. ************ 0 2023-08-28 06:25 31 ************ 1 2023-08-28 06:26 32 ************* ... ..( 2 skipped). .. ************* 4 2023-08-28 06:29 32 ************* 5 2023-08-28 06:30 31 ************ 6 2023-08-28 06:31 31 ************ 7 2023-08-28 06:32 ? - 8 2023-08-28 06:33 31 ************ ... ..( 4 skipped). .. ************ 13 2023-08-28 06:38 31 ************ 14 2023-08-28 06:39 32 ************* ... ..( 11 skipped). .. ************* 26 2023-08-28 06:51 32 ************* 27 2023-08-28 06:52 33 ************** ... ..( 6 skipped). .. ************** 34 2023-08-28 06:59 33 ************** 35 2023-08-28 07:00 32 ************* 36 2023-08-28 07:01 32 ************* 37 2023-08-28 07:02 32 ************* 38 2023-08-28 07:03 ? - 39 2023-08-28 07:04 31 ************ 40 2023-08-28 07:05 31 ************ 41 2023-08-28 07:06 31 ************ 42 2023-08-28 07:07 32 ************* ... ..( 6 skipped). .. ************* 49 2023-08-28 07:14 32 ************* 50 2023-08-28 07:15 33 ************** ... ..( 3 skipped). .. ************** 54 2023-08-28 07:19 33 ************** 55 2023-08-28 07:20 ? - 56 2023-08-28 07:21 31 ************ ... ..( 6 skipped). .. ************ 63 2023-08-28 07:28 31 ************ 64 2023-08-28 07:29 32 ************* ... ..( 2 skipped). .. ************* 67 2023-08-28 07:32 32 ************* 68 2023-08-28 07:33 33 ************** ... ..( 2 skipped). .. ************** 71 2023-08-28 07:36 33 ************** 72 2023-08-28 07:37 34 *************** ... ..( 5 skipped). .. *************** 78 2023-08-28 07:43 34 *************** 79 2023-08-28 07:44 35 **************** ... ..( 3 skipped). .. **************** 83 2023-08-28 07:48 35 **************** 84 2023-08-28 07:49 36 ***************** ... ..( 15 skipped). .. ***************** 100 2023-08-28 08:05 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 2662 Vendor specific