/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.10.0-2-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST500LM012 HN-M500MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2AR10001 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Mar 6 17:23:57 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 254 APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6720) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 112) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 516 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 091 091 025 - 2853 4 Start_Stop_Count -O--CK 087 087 000 - 13442 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 3423 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 098 098 000 - 2389 12 Power_Cycle_Count -O--CK 098 098 000 - 2513 191 G-Sense_Error_Rate -O---K 096 096 000 - 40625 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 050 046 000 - 50 (Min/Max 14/55) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 100 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 1 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 2595 223 Load_Retry_Count -O--CK 098 098 000 - 2389 225 Load_Cycle_Count -O--CK 083 083 000 - 177492 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 362 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 362 [1] occurred at disk power-on lifetime: 383 hours (15 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 00 5c cb d9 40 00 Error: UNC at LBA = 0x005ccbd9 = 6081497 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 5c cb d9 40 00 00:00:02.184 READ FPDMA QUEUED 60 00 00 00 40 00 00 07 da 3e 6a 40 00 00:00:02.249 READ FPDMA QUEUED 60 00 90 00 0a 00 00 01 32 df 1a 40 00 00:00:02.249 READ FPDMA QUEUED 60 00 90 00 09 00 00 03 0c f7 a8 40 00 00:00:02.249 READ FPDMA QUEUED 60 00 90 00 28 00 00 08 2f 7b 92 40 00 00:00:02.249 READ FPDMA QUEUED Error 361 [0] occurred at disk power-on lifetime: 383 hours (15 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 00 5c cb d9 40 00 Error: UNC at LBA = 0x005ccbd9 = 6081497 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 90 00 02 00 00 01 32 df 4b 40 00 00:00:02.223 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 5c cb d9 40 00 00:00:02.149 READ FPDMA QUEUED 60 00 00 00 78 00 00 15 ae da 88 40 00 00:00:02.219 READ FPDMA QUEUED 60 00 90 00 08 00 00 08 22 df 48 40 00 00:00:02.219 READ FPDMA QUEUED 60 00 90 00 58 00 00 15 b6 3a 88 40 00 00:00:02.219 READ FPDMA QUEUED Error 360 [7] occurred at disk power-on lifetime: 383 hours (15 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 00 5c cb d9 40 00 Error: UNC at LBA = 0x005ccbd9 = 6081497 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 07 53 30 25 40 00 00:00:02.193 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 5c cb d9 40 00 00:00:02.149 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 5c cb d9 40 00 00:00:02.189 READ FPDMA QUEUED 60 00 00 00 20 00 00 15 bd b1 b0 40 00 00:00:02.189 READ FPDMA QUEUED 60 00 00 00 01 00 00 08 e0 9d 2f 40 00 00:00:02.189 READ FPDMA QUEUED Error 359 [6] occurred at disk power-on lifetime: 383 hours (15 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 00 5c cb d8 40 00 Error: UNC at LBA = 0x005ccbd8 = 6081496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 5c cb d8 40 00 00:00:02.119 READ FPDMA QUEUED 60 00 90 00 80 00 00 15 b0 95 30 40 00 00:00:02.184 READ FPDMA QUEUED 61 00 90 00 20 00 00 00 5f 1c 48 40 00 00:00:02.184 WRITE FPDMA QUEUED 60 00 90 00 40 00 00 07 db 84 a2 40 00 00:00:02.184 READ FPDMA QUEUED 60 00 90 00 01 00 00 00 5c cb d8 40 00 00:00:02.184 READ FPDMA QUEUED Error 358 [5] occurred at disk power-on lifetime: 383 hours (15 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 00 5c cb d7 40 00 Error: UNC at LBA = 0x005ccbd7 = 6081495 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 90 00 01 00 00 00 5c cb d7 40 00 00:00:02.090 READ FPDMA QUEUED 60 00 90 00 01 00 00 00 5c cb d7 40 00 00:00:02.180 READ FPDMA QUEUED 60 00 90 00 10 00 00 15 b9 bf e8 40 00 00:00:02.180 READ FPDMA QUEUED 60 00 90 00 05 00 00 05 e8 72 c0 40 00 00:00:02.180 READ FPDMA QUEUED 60 00 90 00 10 00 00 00 2c d6 00 40 00 00:00:02.180 READ FPDMA QUEUED Error 357 [4] occurred at disk power-on lifetime: 383 hours (15 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 00 5c cb d7 40 00 Error: UNC at LBA = 0x005ccbd7 = 6081495 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 90 00 10 00 00 15 b9 bf e8 40 00 00:00:02.154 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 5c cb d7 40 00 00:00:02.059 READ FPDMA QUEUED 60 00 90 00 08 00 00 08 09 25 50 40 00 00:00:02.150 READ FPDMA QUEUED 60 00 00 00 40 00 00 08 08 c4 d2 40 00 00:00:02.150 READ FPDMA QUEUED 60 00 90 00 01 00 00 00 5c cb d7 40 00 00:00:02.150 READ FPDMA QUEUED Error 356 [3] occurred at disk power-on lifetime: 383 hours (15 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 00 5c cb d7 40 00 Error: UNC at LBA = 0x005ccbd7 = 6081495 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 90 00 40 00 00 12 90 41 0a 40 00 00:00:02.124 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 5c cb d7 40 00 00:00:02.055 READ FPDMA QUEUED 60 00 00 00 08 00 00 15 bb 7f c0 40 00 00:00:02.119 READ FPDMA QUEUED 60 00 00 00 38 00 00 08 e0 df ea 40 00 00:00:02.119 READ FPDMA QUEUED 60 00 90 00 80 00 00 15 b9 1c 28 40 00 00:00:02.119 READ FPDMA QUEUED Error 355 [2] occurred at disk power-on lifetime: 383 hours (15 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 00 5c cb d7 40 00 Error: UNC at LBA = 0x005ccbd7 = 6081495 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 90 00 01 00 00 08 09 25 80 40 00 00:00:02.094 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 5c cb d7 40 00 00:00:02.050 READ FPDMA QUEUED 60 00 90 00 20 00 00 08 11 e5 00 40 00 00:00:02.090 READ FPDMA QUEUED 60 00 90 00 38 00 00 07 53 21 fa 40 00 00:00:02.090 READ FPDMA QUEUED 60 00 90 00 80 00 00 15 bc 77 c0 40 00 00:00:02.090 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 50 Celsius Power Cycle Min/Max Temperature: 22/52 Celsius Lifetime Min/Max Temperature: 14/66 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (45) Index Estimated Time Temperature Celsius 46 2023-03-06 06:45 50 ******************************* 47 2023-03-06 06:50 47 **************************** ... ..( 38 skipped). .. **************************** 86 2023-03-06 10:05 47 **************************** 87 2023-03-06 10:10 46 *************************** 88 2023-03-06 10:15 47 **************************** ... ..( 3 skipped). .. **************************** 92 2023-03-06 10:35 47 **************************** 93 2023-03-06 10:40 46 *************************** 94 2023-03-06 10:45 46 *************************** 95 2023-03-06 10:50 47 **************************** 96 2023-03-06 10:55 46 *************************** ... ..( 43 skipped). .. *************************** 12 2023-03-06 14:35 46 *************************** 13 2023-03-06 14:40 47 **************************** 14 2023-03-06 14:45 46 *************************** ... ..( 2 skipped). .. *************************** 17 2023-03-06 15:00 46 *************************** 18 2023-03-06 15:05 47 **************************** ... ..( 23 skipped). .. **************************** 42 2023-03-06 17:05 47 **************************** 43 2023-03-06 17:10 48 ***************************** 44 2023-03-06 17:15 50 ******************************* 45 2023-03-06 17:20 50 ******************************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 1799573 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 8 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific