/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.79-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus Device Model: ST3120827AS Serial Number: -- Firmware Version: 3.42 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA/ATAPI-6 T13/1410D revision 2 Local Time is: Mon Mar 27 21:41:51 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 71) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 060 046 006 - 215847454 3 Spin_Up_Time PO---- 098 096 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3864 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 083 060 030 - 205487880 9 Power_On_Hours -O--CK 095 095 000 - 5067 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 097 097 020 - 4095 194 Temperature_Celsius -O---K 042 044 000 - 42 (0 12 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 060 046 000 - 215847454 197 Current_Pending_Sector -O--C- 100 100 000 - 1 198 Offline_Uncorrectable ----C- 100 100 000 - 1 199 UDMA_CRC_Error_Count -OSRCK 200 199 000 - 2 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 SL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 SL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x20 SL R/O 1 Streaming performance log [OBS-8] 0x21 SL R/O 1 Write stream error log 0x22 SL R/O 1 Read stream error log 0x23 SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f SL R/W 16 Host vendor specific log 0xa0 SL VS 1 Device vendor specific log 0xa1 SL VS 20 Device vendor specific log 0xa2 SL VS 101 Device vendor specific log 0xa8 SL VS 20 Device vendor specific log 0xa9 SL VS 1 Device vendor specific log 0xe0 SL R/W 1 SCT Command/Status 0xe1 SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 1386 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1386 occurred at disk power-on lifetime: 4147 hours (172 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 04 b3 03 c5 e0 Error: UNC 4 sectors at LBA = 0x00c503b3 = 12911539 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 d8 08 af 03 c5 e0 00 00:03:57.608 READ DMA EXT 35 d8 08 6f e0 11 e0 00 00:03:57.594 WRITE DMA EXT 25 d8 01 a7 8a cb e0 00 00:03:53.780 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:03:52.785 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:03:52.785 READ DMA EXT Error 1385 occurred at disk power-on lifetime: 4147 hours (172 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 04 b3 03 c5 e0 Error: UNC 4 sectors at LBA = 0x00c503b3 = 12911539 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 d8 08 af 03 c5 e0 00 00:03:57.608 READ DMA EXT 25 d8 01 a7 8a cb e0 00 00:03:57.594 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:03:53.780 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:03:52.785 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:03:52.785 READ DMA EXT Error 1384 occurred at disk power-on lifetime: 4147 hours (172 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 04 b3 03 c5 e0 Error: UNC 4 sectors at LBA = 0x00c503b3 = 12911539 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 d8 08 af 03 c5 e0 00 00:03:44.094 READ DMA EXT 25 d8 01 a7 8a cb e0 00 00:03:44.094 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:03:53.780 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:03:52.785 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:03:52.785 READ DMA EXT Error 1383 occurred at disk power-on lifetime: 4147 hours (172 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 04 b3 03 c5 e0 Error: UNC 4 sectors at LBA = 0x00c503b3 = 12911539 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 d8 08 af 03 c5 e0 00 00:03:44.094 READ DMA EXT 25 d8 01 a7 8a cb e0 00 00:03:44.094 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:03:44.094 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:03:44.094 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:03:44.094 READ DMA EXT Error 1382 occurred at disk power-on lifetime: 4147 hours (172 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 04 b3 03 c5 e0 Error: UNC 4 sectors at LBA = 0x00c503b3 = 12911539 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 d8 08 af 03 c5 e0 00 00:03:44.094 READ DMA EXT 25 d8 08 a7 03 c5 e0 00 00:03:44.094 READ DMA EXT 25 d8 08 9f 03 c5 e0 00 00:03:44.094 READ DMA EXT 25 d8 08 97 03 c5 e0 00 00:03:44.094 READ DMA EXT 25 d8 08 8f 03 c5 e0 00 00:03:44.094 READ DMA EXT SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.79-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST3500418AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: HP35 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Mar 27 21:41:52 2023 MSK ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213891en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 600) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 115 099 006 - 84042921 3 Spin_Up_Time PO---K 098 097 000 - 0 4 Start_Stop_Count -O--CK 089 089 020 - 11938 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 23 7 Seek_Error_Rate POSR-K 084 060 030 - 298850584 9 Power_On_Hours -O--CK 090 090 000 - 9547 10 Spin_Retry_Count PO--CK 100 100 097 - 0 12 Power_Cycle_Count -O--CK 095 095 020 - 5702 180 Unknown_HDD_Attribute PO-R-K 100 100 000 - 33 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 108 188 Command_Timeout -O--CK 100 099 000 - 12885098516 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 057 045 - 37 (Min/Max 37/37) 194 Temperature_Celsius -O---K 037 043 000 - 37 (0 14 0 0 0) 195 Hardware_ECC_Recovered -O-RCK 033 024 000 - 84042921 196 Reallocated_Event_Count -O--CK 100 100 036 - 23 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 128 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 128 [7] occurred at disk power-on lifetime: 7219 hours (300 days + 19 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 04 00:01:55.462 NOP [Abort queued commands] b0 00 d4 00 00 00 00 00 c2 4f 81 a0 00 00:01:27.204 SMART EXECUTE OFF-LINE IMMEDIATE b0 00 d0 00 00 00 00 00 c2 4f 00 a0 00 00:01:26.914 SMART READ DATA b0 00 d0 00 00 00 00 00 c2 4f 00 a0 00 00:01:26.163 SMART READ DATA b0 00 da 00 01 00 00 00 c2 4f 00 a0 00 00:01:20.814 SMART RETURN STATUS Error 127 [6] occurred at disk power-on lifetime: 61 hours (2 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 05 5c 48 72 00 00 Error: UNC at LBA = 0x055c4872 = 89933938 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0a b6 d2 20 40 00 00:19:33.553 READ FPDMA QUEUED 60 00 00 00 20 00 00 1c 96 0f e0 40 00 00:19:33.553 READ FPDMA QUEUED 60 00 00 00 f6 00 00 0e b3 24 70 40 00 00:19:33.553 READ FPDMA QUEUED 60 00 00 00 08 00 00 0a f9 47 f0 40 00 00:19:33.553 READ FPDMA QUEUED 60 00 00 01 00 00 00 06 f7 30 e0 40 00 00:19:33.552 READ FPDMA QUEUED Error 126 [5] occurred at disk power-on lifetime: 61 hours (2 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 05 5c 48 72 00 00 Error: UNC at LBA = 0x055c4872 = 89933938 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0a b6 d2 20 40 00 00:19:30.725 READ FPDMA QUEUED 60 00 00 00 20 00 00 1c 96 0f e0 40 00 00:19:30.724 READ FPDMA QUEUED 60 00 00 00 f6 00 00 0e b3 24 70 40 00 00:19:30.724 READ FPDMA QUEUED 60 00 00 00 08 00 00 0a f9 47 f0 40 00 00:19:30.724 READ FPDMA QUEUED 60 00 00 01 00 00 00 06 f7 30 e0 40 00 00:19:30.723 READ FPDMA QUEUED Error 125 [4] occurred at disk power-on lifetime: 61 hours (2 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 05 5c 48 72 00 00 Error: UNC at LBA = 0x055c4872 = 89933938 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 00 1c 96 0f e0 40 00 00:19:27.559 READ FPDMA QUEUED 60 00 00 00 f6 00 00 0e b3 24 70 40 00 00:19:27.559 READ FPDMA QUEUED 60 00 00 00 08 00 00 0a f9 47 f0 40 00 00:19:27.558 READ FPDMA QUEUED 60 00 00 01 00 00 00 06 f7 30 e0 40 00 00:19:27.558 READ FPDMA QUEUED 60 00 00 00 08 00 00 03 fc 10 68 40 00 00:19:27.558 READ FPDMA QUEUED Error 124 [3] occurred at disk power-on lifetime: 61 hours (2 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 05 5c 48 72 00 00 Error: UNC at LBA = 0x055c4872 = 89933938 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 00 1c 96 0f e0 40 00 00:19:24.732 READ FPDMA QUEUED 60 00 00 00 f6 00 00 0e b3 24 70 40 00 00:19:24.732 READ FPDMA QUEUED 60 00 00 00 08 00 00 0a f9 47 f0 40 00 00:19:24.732 READ FPDMA QUEUED 60 00 00 01 00 00 00 06 f7 30 e0 40 00 00:19:24.732 READ FPDMA QUEUED 60 00 00 00 08 00 00 03 fc 10 68 40 00 00:19:24.731 READ FPDMA QUEUED Error 123 [2] occurred at disk power-on lifetime: 61 hours (2 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 05 5c 48 72 00 00 Error: WP at LBA = 0x055c4872 = 89933938 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 00 03 81 88 40 00 00:19:21.556 WRITE FPDMA QUEUED 60 00 00 00 08 00 00 0a f9 47 f0 40 00 00:19:21.556 READ FPDMA QUEUED 61 00 00 00 01 00 00 00 03 a8 10 40 00 00:19:21.555 WRITE FPDMA QUEUED 60 00 00 01 00 00 00 06 f7 30 e0 40 00 00:19:21.555 READ FPDMA QUEUED 60 00 00 00 08 00 00 03 fc 10 68 40 00 00:19:21.555 READ FPDMA QUEUED Error 122 [1] occurred at disk power-on lifetime: 61 hours (2 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 05 5c 48 72 00 00 Error: UNC at LBA = 0x055c4872 = 89933938 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 06 f7 30 e0 40 00 00:19:18.386 READ FPDMA QUEUED 60 00 00 00 08 00 00 03 fc 10 68 40 00 00:19:18.385 READ FPDMA QUEUED 60 00 00 01 00 00 00 09 2c ee 30 40 00 00:19:18.385 READ FPDMA QUEUED 60 00 00 00 20 00 00 05 5c 48 60 40 00 00:19:18.385 READ FPDMA QUEUED f5 00 00 00 00 00 00 00 00 00 00 00 00 00:19:18.384 SECURITY FREEZE LOCK Error 121 [0] occurred at disk power-on lifetime: 61 hours (2 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 05 5c 48 72 00 00 Error: UNC at LBA = 0x055c4872 = 89933938 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 18 00 00 0f dc 10 d2 40 00 00:19:15.194 READ FPDMA QUEUED 60 00 00 01 00 00 00 09 2c ee 30 40 00 00:19:15.194 READ FPDMA QUEUED 60 00 00 00 20 00 00 05 5c 48 60 40 00 00:19:15.194 READ FPDMA QUEUED 60 00 00 00 8e 00 00 00 1a 2c 20 40 00 00:19:15.193 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:19:15.109 READ LOG EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 9219 - # 2 Short offline Completed without error 00% 8858 - # 3 Short captive Interrupted (host reset) 80% 7219 - # 4 Short offline Completed without error 00% 5527 - # 5 Extended offline Aborted by host 90% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 37/37 Celsius Lifetime Min/Max Temperature: 14/43 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (6) Index Estimated Time Temperature Celsius 7 2023-03-22 16:47 32 ************* 8 2023-03-22 17:46 32 ************* 9 2023-03-22 18:45 ? - 10 2023-03-22 19:44 23 **** 11 2023-03-22 20:43 23 **** 12 2023-03-22 21:42 ? - 13 2023-03-22 22:41 23 **** 14 2023-03-22 23:40 23 **** 15 2023-03-23 00:39 32 ************* 16 2023-03-23 01:38 33 ************** 17 2023-03-23 02:37 32 ************* 18 2023-03-23 03:36 31 ************ 19 2023-03-23 04:35 32 ************* ... ..( 3 skipped). .. ************* 23 2023-03-23 08:31 32 ************* 24 2023-03-23 09:30 31 ************ 25 2023-03-23 10:29 31 ************ 26 2023-03-23 11:28 ? - 27 2023-03-23 12:27 23 **** 28 2023-03-23 13:26 23 **** 29 2023-03-23 14:25 ? - 30 2023-03-23 15:24 23 **** 31 2023-03-23 16:23 23 **** 32 2023-03-23 17:22 33 ************** 33 2023-03-23 18:21 32 ************* 34 2023-03-23 19:20 31 ************ 35 2023-03-23 20:19 ? - 36 2023-03-23 21:18 22 *** 37 2023-03-23 22:17 22 *** 38 2023-03-23 23:16 ? - 39 2023-03-24 00:15 22 *** 40 2023-03-24 01:14 22 *** 41 2023-03-24 02:13 ? - 42 2023-03-24 03:12 22 *** 43 2023-03-24 04:11 22 *** 44 2023-03-24 05:10 ? - 45 2023-03-24 06:09 21 ** 46 2023-03-24 07:08 21 ** 47 2023-03-24 08:07 32 ************* 48 2023-03-24 09:06 32 ************* 49 2023-03-24 10:05 ? - 50 2023-03-24 11:04 31 ************ 51 2023-03-24 12:03 31 ************ 52 2023-03-24 13:02 32 ************* ... ..( 2 skipped). .. ************* 55 2023-03-24 15:59 32 ************* 56 2023-03-24 16:58 33 ************** 57 2023-03-24 17:57 32 ************* ... ..( 2 skipped). .. ************* 60 2023-03-24 20:54 32 ************* 61 2023-03-24 21:53 ? - 62 2023-03-24 22:52 22 *** 63 2023-03-24 23:51 22 *** 64 2023-03-25 00:50 32 ************* 65 2023-03-25 01:49 32 ************* 66 2023-03-25 02:48 32 ************* 67 2023-03-25 03:47 33 ************** 68 2023-03-25 04:46 32 ************* 69 2023-03-25 05:45 33 ************** 70 2023-03-25 06:44 ? - 71 2023-03-25 07:43 23 **** 72 2023-03-25 08:42 23 **** 73 2023-03-25 09:41 ? - 74 2023-03-25 10:40 22 *** 75 2023-03-25 11:39 22 *** 76 2023-03-25 12:38 33 ************** ... ..( 6 skipped). .. ************** 83 2023-03-25 19:31 33 ************** 84 2023-03-25 20:30 ? - 85 2023-03-25 21:29 26 ******* 86 2023-03-25 22:28 ? - 87 2023-03-25 23:27 24 ***** 88 2023-03-26 00:26 ? - 89 2023-03-26 01:25 26 ******* 90 2023-03-26 02:24 26 ******* 91 2023-03-26 03:23 ? - 92 2023-03-26 04:22 23 **** 93 2023-03-26 05:21 23 **** 94 2023-03-26 06:20 32 ************* 95 2023-03-26 07:19 ? - 96 2023-03-26 08:18 21 ** 97 2023-03-26 09:17 21 ** 98 2023-03-26 10:16 ? - 99 2023-03-26 11:15 22 *** 100 2023-03-26 12:14 22 *** 101 2023-03-26 13:13 ? - 102 2023-03-26 14:12 22 *** 103 2023-03-26 15:11 22 *** 104 2023-03-26 16:10 ? - 105 2023-03-26 17:09 22 *** 106 2023-03-26 18:08 22 *** 107 2023-03-26 19:07 ? - 108 2023-03-26 20:06 22 *** 109 2023-03-26 21:05 22 *** 110 2023-03-26 22:04 ? - 111 2023-03-26 23:03 23 **** 112 2023-03-27 00:02 23 **** 113 2023-03-27 01:01 ? - 114 2023-03-27 02:00 23 **** 115 2023-03-27 02:59 23 **** 116 2023-03-27 03:58 ? - 117 2023-03-27 04:57 26 ******* 118 2023-03-27 05:56 ? - 119 2023-03-27 06:55 23 **** 120 2023-03-27 07:54 ? - 121 2023-03-27 08:53 23 **** 122 2023-03-27 09:52 23 **** 123 2023-03-27 10:51 ? - 124 2023-03-27 11:50 24 ***** 125 2023-03-27 12:49 24 ***** 126 2023-03-27 13:48 ? - 127 2023-03-27 14:47 22 *** 0 2023-03-27 15:46 ? - 1 2023-03-27 16:45 26 ******* 2 2023-03-27 17:44 ? - 3 2023-03-27 18:43 35 **************** 4 2023-03-27 19:42 ? - 5 2023-03-27 20:41 37 ****************** 6 2023-03-27 21:40 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS