/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-52-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Laptop SSHD Device Model: ST1000LM014-1EJ164 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: SM25 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Nov 8 08:56:12 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 128) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 191) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x10b1) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 108 099 006 - 14820120 3 Spin_Up_Time PO---- 099 097 000 - 0 4 Start_Stop_Count -O--CK 082 082 020 - 18720 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 078 060 030 - 17459743575 9 Power_On_Hours -O--CK 095 095 000 - 5159 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 093 093 020 - 7711 184 End-to-End_Error -O--CK 099 099 099 NOW 1 187 Reported_Uncorrect -O--CK 095 095 000 - 5 188 Command_Timeout -O--CK 100 099 000 - 722812 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 072 045 045 Past 28 (Min/Max 19/28) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 339 193 Load_Cycle_Count -O--CK 088 088 000 - 24534 194 Temperature_Celsius -O---K 028 055 000 - 28 (0 14 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 5 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 3900 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xae GPL VS 1 Device vendor specific log 0xb0 GPL VS 4580 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc2 GPL,SL VS 50 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 6 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [5] occurred at disk power-on lifetime: 4937 hours (205 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3a 15 48 a8 00 00 Error: UNC at LBA = 0x3a1548a8 = 974473384 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 60 00 00 3a 15 50 f8 40 00 00:00:28.193 READ FPDMA QUEUED 60 00 00 00 08 00 00 3a 15 50 f0 40 00 00:00:28.193 READ FPDMA QUEUED 60 00 00 00 08 00 00 3a 15 50 e8 40 00 00:00:28.193 READ FPDMA QUEUED 60 00 00 00 08 00 00 3a 15 50 e0 40 00 00:00:28.193 READ FPDMA QUEUED 60 00 00 00 08 00 00 3a 15 50 d8 40 00 00:00:28.193 READ FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 4767 hours (198 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 7b c7 d0 00 00 Error: UNC at LBA = 0x007bc7d0 = 8112080 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 2e 5d 1c 20 40 00 00:00:18.248 READ FPDMA QUEUED 60 00 00 01 00 00 00 2e 5d 1b 20 40 00 00:00:18.248 READ FPDMA QUEUED 60 00 00 01 00 00 00 2e 5d 1a 20 40 00 00:00:18.248 READ FPDMA QUEUED 60 00 00 01 00 00 00 2e 5d 19 20 40 00 00:00:18.248 READ FPDMA QUEUED 60 00 00 01 00 00 00 2e 5d 18 20 40 00 00:00:18.248 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 4767 hours (198 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 7b c7 d0 00 00 Error: UNC at LBA = 0x007bc7d0 = 8112080 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 1b b8 4f 20 40 00 00:00:14.216 READ FPDMA QUEUED 60 00 00 01 00 00 00 1b b8 4e 20 40 00 00:00:14.216 READ FPDMA QUEUED 60 00 00 01 00 00 00 1b b8 4d 20 40 00 00:00:14.216 READ FPDMA QUEUED 60 00 00 01 00 00 00 1b b8 4c 20 40 00 00:00:14.216 READ FPDMA QUEUED 60 00 00 01 00 00 00 1b b8 4b 20 40 00 00:00:14.215 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 4767 hours (198 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 7b c7 d0 00 00 Error: UNC at LBA = 0x007bc7d0 = 8112080 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 7b c7 d0 40 00 00:00:19.933 READ FPDMA QUEUED 60 00 00 00 20 00 00 1b a7 e8 40 40 00 00:00:19.932 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:00:19.774 READ LOG EXT 60 00 00 00 08 00 00 00 7b c3 08 40 00 00:00:15.838 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 7b bc 80 40 00 00:00:15.824 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 4767 hours (198 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 7b c7 d0 00 00 Error: UNC at LBA = 0x007bc7d0 = 8112080 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 7b c3 08 40 00 00:00:15.838 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 7b bc 80 40 00 00:00:15.824 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 7b bc 78 40 00 00:00:15.807 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 7b bc 70 40 00 00:00:15.807 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 7b bc 68 40 00 00:00:15.806 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 3251 hours (135 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 28 d9 38 00 00 Error: WP at LBA = 0x0028d938 = 2677048 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 01 00 00 00 19 b4 76 00 40 00 00:00:21.732 WRITE FPDMA QUEUED 60 00 00 00 40 00 00 01 63 88 a2 40 00 00:00:21.731 READ FPDMA QUEUED 60 00 00 00 38 00 00 00 b8 25 a2 40 00 00:00:21.731 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 97 12 38 40 00 00:00:21.731 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 de 81 e0 40 00 00:00:21.731 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - # 2 Short offline Completed without error 00% 0 - # 3 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 19 Celsius Power Cycle Min/Max Temperature: 19/25 Celsius Lifetime Min/Max Temperature: 16/55 Celsius Under/Over Temperature Limit Count: 0/1 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (68) Index Estimated Time Temperature Celsius 69 2022-11-03 03:31 36 ***************** 70 2022-11-03 04:30 37 ****************** 71 2022-11-03 05:29 39 ******************** 72 2022-11-03 06:28 ? - 73 2022-11-03 07:27 25 ****** 74 2022-11-03 08:26 33 ************** 75 2022-11-03 09:25 38 ******************* 76 2022-11-03 10:24 38 ******************* 77 2022-11-03 11:23 ? - 78 2022-11-03 12:22 25 ****** 79 2022-11-03 13:21 36 ***************** 80 2022-11-03 14:20 43 ************************ 81 2022-11-03 15:19 39 ******************** 82 2022-11-03 16:18 39 ******************** 83 2022-11-03 17:17 36 ***************** 84 2022-11-03 18:16 39 ******************** 85 2022-11-03 19:15 48 ***************************** 86 2022-11-03 20:14 41 ********************** 87 2022-11-03 21:13 45 ************************** 88 2022-11-03 22:12 37 ****************** 89 2022-11-03 23:11 ? - 90 2022-11-04 00:10 25 ****** 91 2022-11-04 01:09 37 ****************** 92 2022-11-04 02:08 39 ******************** 93 2022-11-04 03:07 ? - 94 2022-11-04 04:06 25 ****** 95 2022-11-04 05:05 27 ******** 96 2022-11-04 06:04 36 ***************** 97 2022-11-04 07:03 38 ******************* 98 2022-11-04 08:02 36 ***************** 99 2022-11-04 09:01 ? - 100 2022-11-04 10:00 25 ****** 101 2022-11-04 10:59 18 - 102 2022-11-04 11:58 35 **************** 103 2022-11-04 12:57 ? - 104 2022-11-04 13:56 25 ****** 105 2022-11-04 14:55 20 * 106 2022-11-04 15:54 38 ******************* 107 2022-11-04 16:53 ? - 108 2022-11-04 17:52 25 ****** 109 2022-11-04 18:51 19 - 110 2022-11-04 19:50 35 **************** 111 2022-11-04 20:49 ? - 112 2022-11-04 21:48 25 ****** 113 2022-11-04 22:47 26 ******* 114 2022-11-04 23:46 37 ****************** 115 2022-11-05 00:45 ? - 116 2022-11-05 01:44 25 ****** 117 2022-11-05 02:43 21 ** 118 2022-11-05 03:42 37 ****************** 119 2022-11-05 04:41 ? - 120 2022-11-05 05:40 25 ****** 121 2022-11-05 06:39 32 ************* 122 2022-11-05 07:38 36 ***************** 123 2022-11-05 08:37 ? - 124 2022-11-05 09:36 25 ****** 125 2022-11-05 10:35 32 ************* 126 2022-11-05 11:34 37 ****************** 127 2022-11-05 12:33 ? - 0 2022-11-05 13:32 25 ****** 1 2022-11-05 14:31 17 - 2 2022-11-05 15:30 36 ***************** 3 2022-11-05 16:29 ? - 4 2022-11-05 17:28 25 ****** 5 2022-11-05 18:27 31 ************ 6 2022-11-05 19:26 34 *************** 7 2022-11-05 20:25 ? - 8 2022-11-05 21:24 25 ****** 9 2022-11-05 22:23 31 ************ 10 2022-11-05 23:22 38 ******************* 11 2022-11-06 00:21 39 ******************** 12 2022-11-06 01:20 ? - 13 2022-11-06 02:19 25 ****** 14 2022-11-06 03:18 27 ******** 15 2022-11-06 04:17 36 ***************** 16 2022-11-06 05:16 ? - 17 2022-11-06 06:15 25 ****** 18 2022-11-06 07:14 34 *************** 19 2022-11-06 08:13 37 ****************** 20 2022-11-06 09:12 38 ******************* 21 2022-11-06 10:11 ? - 22 2022-11-06 11:10 25 ****** 23 2022-11-06 12:09 20 * 24 2022-11-06 13:08 37 ****************** 25 2022-11-06 14:07 ? - 26 2022-11-06 15:06 25 ****** 27 2022-11-06 16:05 18 - 28 2022-11-06 17:04 35 **************** 29 2022-11-06 18:03 ? - 30 2022-11-06 19:02 25 ****** 31 2022-11-06 20:01 20 * 32 2022-11-06 21:00 38 ******************* 33 2022-11-06 21:59 ? - 34 2022-11-06 22:58 25 ****** 35 2022-11-06 23:57 39 ******************** 36 2022-11-07 00:56 44 ************************* 37 2022-11-07 01:55 38 ******************* 38 2022-11-07 02:54 36 ***************** 39 2022-11-07 03:53 ? - 40 2022-11-07 04:52 25 ****** 41 2022-11-07 05:51 26 ******* 42 2022-11-07 06:50 39 ******************** 43 2022-11-07 07:49 ? - 44 2022-11-07 08:48 25 ****** 45 2022-11-07 09:47 23 **** 46 2022-11-07 10:46 38 ******************* 47 2022-11-07 11:45 40 ********************* 48 2022-11-07 12:44 40 ********************* 49 2022-11-07 13:43 ? - 50 2022-11-07 14:42 25 ****** 51 2022-11-07 15:41 21 ** 52 2022-11-07 16:40 37 ****************** 53 2022-11-07 17:39 38 ******************* 54 2022-11-07 18:38 ? - 55 2022-11-07 19:37 25 ****** 56 2022-11-07 20:36 35 **************** 57 2022-11-07 21:35 39 ******************** 58 2022-11-07 22:34 40 ********************* 59 2022-11-07 23:33 40 ********************* 60 2022-11-08 00:32 40 ********************* 61 2022-11-08 01:31 ? - 62 2022-11-08 02:30 25 ****** 63 2022-11-08 03:29 20 * 64 2022-11-08 04:28 38 ******************* 65 2022-11-08 05:27 39 ******************** 66 2022-11-08 06:26 ? - 67 2022-11-08 07:25 25 ****** 68 2022-11-08 08:24 19 - SCT Error Recovery Control command not supported ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read Device Statistics page 0x00 failed Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-52-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: BHT WR202I0032G E70290F5 Serial Number: -- Firmware Version: 90014a User Capacity: 31,268,536,320 bytes [31.2 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ATA/ATAPI-7 T13/1532D revision 1 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Nov 8 08:56:12 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Unavailable Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1115) seconds. Offline data collection capabilities: (0x1d) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 18) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 9 Power_On_Hours -O--CK 100 100 000 - 747 12 Power_Cycle_Count -O--CK 100 100 000 - 1448 173 Unknown_Attribute -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 4052 194 Temperature_Celsius -O---K 100 120 000 - 32 199 UDMA_CRC_Error_Count PO--CK 100 100 000 - 8 241 Total_LBAs_Written -O--CK 100 100 000 - 1804 242 Total_LBAs_Read -O--CK 100 100 000 - 2361 234 Unknown_Attribute -O--CK 100 100 000 - 0 235 Unknown_Attribute -O--CK 100 100 000 - 0 236 Unknown_Attribute -O--CK 100 100 000 - 0 237 Unknown_Attribute -O--CK 100 100 000 - 0 243 Unknown_Attribute -O--CK 100 100 000 - 0 244 Unknown_Attribute -O--CK 100 100 000 - 0 245 Unknown_Attribute -O--CK 100 100 000 - 0 246 Unknown_Attribute -O--CK 100 100 000 - 0 247 Unknown_Attribute -O--CK 100 100 000 - 257 248 Unknown_Attribute -O--CK 100 100 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning Read SMART Log Directory failed: scsi error badly formed scsi parameters General Purpose Log Directory not supported SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 No Errors Logged SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported