/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.58-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: WD Blue / Red / Green SSDs Device Model: WDC WDS120G2G0A-00JH30 Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: UE500000 User Capacity: 120,040,980,480 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5528 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Nov 8 10:36:55 2023 +10 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 32) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x15) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 21) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 14216 12 Power_Cycle_Count -O--CK 100 100 000 - 4963 165 Block_Erase_Count -O--CK 100 100 000 - 10141 166 Minimum_PE_Cycles_TLC -O--CK 100 100 --- - 101 167 Max_Bad_Blocks_per_Die -O--CK 100 100 --- - 0 168 Maximum_PE_Cycles_TLC -O--CK 100 100 --- - 128 169 Total_Bad_Blocks -O--CK 100 100 --- - 114 170 Grown_Bad_Blocks -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Average_PE_Cycles_TLC -O--CK 100 100 000 - 101 174 Unexpected_Power_Loss -O--CK 100 100 000 - 1493 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 062 055 000 - 38 (Min/Max 10/55) 199 UDMA_CRC_Error_Count -O--CK 100 100 --- - 0 230 Media_Wearout_Indicator -O--CK 100 100 000 - 0x1c6114141c61 232 Available_Reservd_Space PO--CK 100 100 005 - 100 233 NAND_GB_Written_TLC -O--CK 100 100 --- - 12162 234 NAND_GB_Written_SLC -O--CK 100 100 000 - 56415 241 Host_Writes_GiB ----CK 100 100 000 - 21739 242 Host_Reads_GiB ----CK 100 100 000 - 22861 244 Temp_Throttle_Status -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log 0xa7 GPL,SL VS 1 Device vendor specific log 0xa9 GPL,SL VS 3 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (16 sectors) Device Error Count: 62 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 62 [1] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 25 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 24 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 23 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 22 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 21 3d+07:32:11.153 NOP [Abort queued commands] Error 61 [0] occurred at disk power-on lifetime: 43981 hours (1832 days + 13 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 15 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 14 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 13 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 12 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 11 3d+07:32:11.153 NOP [Abort queued commands] Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. Error 60 [63] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 45 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 44 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 43 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 42 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 41 3d+07:32:11.153 NOP [Abort queued commands] Error 59 [62] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 35 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 34 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 33 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 32 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 31 3d+07:32:11.153 NOP [Abort queued commands] Error 58 [61] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 25 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 24 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 23 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 22 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 21 3d+07:32:11.153 NOP [Abort queued commands] Error 57 [60] occurred at disk power-on lifetime: 43981 hours (1832 days + 13 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 15 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 14 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 13 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 12 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 11 3d+07:32:11.153 NOP [Abort queued commands] Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. Error 56 [59] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 45 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 44 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 43 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 42 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 41 3d+07:32:11.153 NOP [Abort queued commands] Error 55 [58] occurred at disk power-on lifetime: 61166 hours (2548 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 35 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 34 13d+06:08:44.612 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 33 9d+22:36:33.459 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 32 6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 31 3d+07:32:11.153 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 4963 --- Lifetime Power-On Resets 0x01 0x010 4 14216 --- Power-on Hours 0x01 0x018 6 45590757953 --- Logical Sectors Written 0x01 0x028 6 47944221096 --- Logical Sectors Read 0x01 0x038 6 14216 --- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 38 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 54 --- Highest Temperature 0x05 0x028 1 26 --- Lowest Temperature 0x05 0x030 1 39 --- Highest Average Short Term Temperature 0x05 0x038 1 39 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 20 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error /dev/sdb smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.58-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST3250318AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC38 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Nov 8 10:36:55 2023 +10 ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213891en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 0 (vendor specific), recommended: 254 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 617) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 48) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 099 006 - 153698326 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 074 074 020 - 27533 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 085 060 030 - 397210042 9 Power_On_Hours -O--CK 068 068 000 - 28419 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 088 088 020 - 12478 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 099 000 - 4 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 050 045 - 37 (Min/Max 35/38) 194 Temperature_Celsius -O---K 037 050 000 - 37 (0 11 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 042 024 000 - 153698326 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 62307 (19 129 0) 241 Total_LBAs_Written ------ 100 253 000 - 3566169857 242 Total_LBAs_Read ------ 100 253 000 - 2416367734 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 35/38 Celsius Lifetime Min/Max Temperature: 11/50 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (70) Index Estimated Time Temperature Celsius 71 2023-11-03 05:10 ? - 72 2023-11-03 06:09 23 **** 73 2023-11-03 07:08 ? - 74 2023-11-03 08:07 18 - 75 2023-11-03 09:06 ? - 76 2023-11-03 10:05 19 - 77 2023-11-03 11:04 ? - 78 2023-11-03 12:03 26 ******* 79 2023-11-03 13:02 ? - 80 2023-11-03 14:01 25 ****** 81 2023-11-03 15:00 ? - 82 2023-11-03 15:59 19 - 83 2023-11-03 16:58 ? - 84 2023-11-03 17:57 23 **** 85 2023-11-03 18:56 ? - 86 2023-11-03 19:55 20 * 87 2023-11-03 20:54 20 * 88 2023-11-03 21:53 ? - 89 2023-11-03 22:52 20 * 90 2023-11-03 23:51 20 * 91 2023-11-04 00:50 33 ************** 92 2023-11-04 01:49 32 ************* 93 2023-11-04 02:48 37 ****************** 94 2023-11-04 03:47 38 ******************* 95 2023-11-04 04:46 ? - 96 2023-11-04 05:45 34 *************** 97 2023-11-04 06:44 ? - 98 2023-11-04 07:43 21 ** 99 2023-11-04 08:42 ? - 100 2023-11-04 09:41 21 ** 101 2023-11-04 10:40 21 ** 102 2023-11-04 11:39 ? - 103 2023-11-04 12:38 20 * 104 2023-11-04 13:37 20 * 105 2023-11-04 14:36 31 ************ 106 2023-11-04 15:35 ? - 107 2023-11-04 16:34 21 ** 108 2023-11-04 17:33 21 ** 109 2023-11-04 18:32 ? - 110 2023-11-04 19:31 21 ** 111 2023-11-04 20:30 ? - 112 2023-11-04 21:29 22 *** 113 2023-11-04 22:28 ? - 114 2023-11-04 23:27 24 ***** 115 2023-11-05 00:26 ? - 116 2023-11-05 01:25 22 *** 117 2023-11-05 02:24 22 *** 118 2023-11-05 03:23 36 ***************** 119 2023-11-05 04:22 ? - 120 2023-11-05 05:21 24 ***** 121 2023-11-05 06:20 ? - 122 2023-11-05 07:19 24 ***** 123 2023-11-05 08:18 24 ***** 124 2023-11-05 09:17 ? - 125 2023-11-05 10:16 21 ** 126 2023-11-05 11:15 21 ** 127 2023-11-05 12:14 ? - 0 2023-11-05 13:13 24 ***** 1 2023-11-05 14:12 24 ***** 2 2023-11-05 15:11 42 *********************** 3 2023-11-05 16:10 44 ************************* 4 2023-11-05 17:09 44 ************************* 5 2023-11-05 18:08 43 ************************ 6 2023-11-05 19:07 43 ************************ 7 2023-11-05 20:06 39 ******************** 8 2023-11-05 21:05 39 ******************** 9 2023-11-05 22:04 ? - 10 2023-11-05 23:03 20 * 11 2023-11-06 00:02 ? - 12 2023-11-06 01:01 21 ** 13 2023-11-06 02:00 21 ** 14 2023-11-06 02:59 ? - 15 2023-11-06 03:58 38 ******************* 16 2023-11-06 04:57 38 ******************* 17 2023-11-06 05:56 ? - 18 2023-11-06 06:55 21 ** 19 2023-11-06 07:54 ? - 20 2023-11-06 08:53 33 ************** 21 2023-11-06 09:52 ? - 22 2023-11-06 10:51 20 * 23 2023-11-06 11:50 20 * 24 2023-11-06 12:49 33 ************** 25 2023-11-06 13:48 ? - 26 2023-11-06 14:47 21 ** 27 2023-11-06 15:46 21 ** 28 2023-11-06 16:45 34 *************** 29 2023-11-06 17:44 39 ******************** 30 2023-11-06 18:43 38 ******************* 31 2023-11-06 19:42 38 ******************* 32 2023-11-06 20:41 ? - 33 2023-11-06 21:40 18 - 34 2023-11-06 22:39 18 - 35 2023-11-06 23:38 32 ************* 36 2023-11-07 00:37 ? - 37 2023-11-07 01:36 18 - 38 2023-11-07 02:35 ? - 39 2023-11-07 03:34 21 ** 40 2023-11-07 04:33 21 ** 41 2023-11-07 05:32 ? - 42 2023-11-07 06:31 30 *********** 43 2023-11-07 07:30 ? - 44 2023-11-07 08:29 19 - 45 2023-11-07 09:28 ? - 46 2023-11-07 10:27 21 ** 47 2023-11-07 11:26 21 ** 48 2023-11-07 12:25 ? - 49 2023-11-07 13:24 20 * 50 2023-11-07 14:23 ? - 51 2023-11-07 15:22 26 ******* 52 2023-11-07 16:21 26 ******* 53 2023-11-07 17:20 ? - 54 2023-11-07 18:19 29 ********** 55 2023-11-07 19:18 ? - 56 2023-11-07 20:17 21 ** 57 2023-11-07 21:16 ? - 58 2023-11-07 22:15 20 * 59 2023-11-07 23:14 ? - 60 2023-11-08 00:13 22 *** 61 2023-11-08 01:12 22 *** 62 2023-11-08 02:11 ? - 63 2023-11-08 03:10 23 **** 64 2023-11-08 04:09 ? - 65 2023-11-08 05:08 21 ** 66 2023-11-08 06:07 21 ** 67 2023-11-08 07:06 ? - 68 2023-11-08 08:05 35 **************** 69 2023-11-08 09:04 35 **************** 70 2023-11-08 10:03 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdg smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.58-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD20SDRW-11VUUS1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 2,000,365,379,584 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Nov 8 10:36:55 2023 +10 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (17520) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 290) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 194 188 021 - 3291 4 Start_Stop_Count -O--CK 097 097 000 - 3624 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 093 093 000 - 5527 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 981 192 Power-Off_Retract_Count -O--CK 200 200 000 - 558 193 Load_Cycle_Count -O--CK 186 186 000 - 43215 194 Temperature_Celsius -O---K 111 091 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 288 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 76 Device vendor specific log 0xb9 GPL,SL VS 4 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xcf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 22/37 Celsius Lifetime Min/Max Temperature: 17/56 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (49) Index Estimated Time Temperature Celsius 50 2023-11-08 08:29 35 **************** ... ..( 17 skipped). .. **************** 68 2023-11-08 08:47 35 **************** 69 2023-11-08 08:48 34 *************** 70 2023-11-08 08:49 35 **************** 71 2023-11-08 08:50 34 *************** 72 2023-11-08 08:51 34 *************** 73 2023-11-08 08:52 34 *************** 74 2023-11-08 08:53 35 **************** 75 2023-11-08 08:54 ? - 76 2023-11-08 08:55 35 **************** 77 2023-11-08 08:56 35 **************** 78 2023-11-08 08:57 34 *************** 79 2023-11-08 08:58 34 *************** 80 2023-11-08 08:59 ? - 81 2023-11-08 09:00 34 *************** 82 2023-11-08 09:01 35 **************** 83 2023-11-08 09:02 34 *************** 84 2023-11-08 09:03 35 **************** 85 2023-11-08 09:04 34 *************** 86 2023-11-08 09:05 35 **************** 87 2023-11-08 09:06 35 **************** 88 2023-11-08 09:07 35 **************** 89 2023-11-08 09:08 34 *************** 90 2023-11-08 09:09 35 **************** ... ..( 46 skipped). .. **************** 9 2023-11-08 09:56 35 **************** 10 2023-11-08 09:57 36 ***************** 11 2023-11-08 09:58 36 ***************** 12 2023-11-08 09:59 37 ****************** 13 2023-11-08 10:00 36 ***************** 14 2023-11-08 10:01 37 ****************** 15 2023-11-08 10:02 37 ****************** 16 2023-11-08 10:03 37 ****************** 17 2023-11-08 10:04 36 ***************** ... ..( 13 skipped). .. ***************** 31 2023-11-08 10:18 36 ***************** 32 2023-11-08 10:19 37 ****************** 33 2023-11-08 10:20 36 ***************** ... ..( 15 skipped). .. ***************** 49 2023-11-08 10:36 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 10457 Vendor specific