/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD2500AAJS-00VTA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01B01 User Capacity: 250,058,268,160 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) Local Time is: Sun Jan 19 16:21:47 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 59) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 1591 3 Spin_Up_Time PO---- 176 175 021 - 2183 4 Start_Stop_Count -O--CK 099 099 000 - 1706 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 000 - 0 9 Power_On_Hours -O--CK 044 044 000 - 41021 10 Spin_Retry_Count -O--C- 100 100 000 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 092 092 000 - 8145 192 Power-Off_Retract_Count -O--CK 195 195 000 - 3943 193 Load_Cycle_Count -O--CK 198 198 000 - 8145 194 Temperature_Celsius -O---K 106 085 000 - 37 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 113 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 3705 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3705 [8] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 e4 25 07 2f 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 00 07 e3 00 2f 25 00 00 00 00:00:32.896 NOP [Abort queued commands] 00 e2 25 07 2f 00 80 00 80 00 00 00 00 00:07:51.010 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 80 07 e1 00 2f 25 00 00 00 00:00:00.128 NOP [Abort queued commands] Error 3704 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 5f 25 06 36 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 50 06 5e 00 36 25 00 00 00 00:00:53.376 NOP [Abort queued commands] 00 5d 25 06 36 00 80 00 d0 00 00 00 00 00:06:47.134 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 d0 06 5d 00 36 25 00 00 00 00:00:20.608 NOP [Abort queued commands] Error 3703 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 e8 25 0c a5 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 08 0c 72 00 9a 25 00 00 00 00:00:02.056 NOP [Abort queued commands] 00 62 25 0c 9a 00 08 00 08 00 00 00 00 00:13:45.954 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 00 00 30 0c 61 00 9a 25 00 00 00 00:00:22.536 NOP [Abort queued commands] Error 3702 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 72 25 0c 9a 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 08 0c 62 00 9a 25 00 00 00 00:00:02.056 NOP [Abort queued commands] 00 61 25 0c 9a 00 08 00 58 00 00 00 00 00:13:45.954 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 30 0c 61 00 9a 25 00 00 00 00:00:12.304 NOP [Abort queued commands] Error 3701 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 10 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 41 25 0b c4 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 03 00 00 0b 47 00 b7 25 00 00 00 00:00:00.016 NOP [Reserved subcommand] [OBS-ACS-2] 00 8d 25 0b 9f 00 10 00 00 03 00 00 00 00:12:44.685 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 03 00 00 0b 99 00 92 25 00 00 00 00:00:00.016 NOP [Reserved subcommand] [OBS-ACS-2] Error 3700 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 10 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 47 25 0b b7 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 03 00 00 0b 0d 00 ab 25 00 00 00 00:00:00.016 NOP [Reserved subcommand] [OBS-ACS-2] 00 99 25 0b 92 00 10 00 00 03 00 00 00 00:12:41.741 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 03 00 00 0b 19 00 87 25 00 00 00 00:00:00.016 NOP [Reserved subcommand] [OBS-ACS-2] Error 3699 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 10 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 0d 25 0b ab 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 03 00 00 0b 8d 00 9f 25 00 00 00 00:00:00.016 NOP [Reserved subcommand] [OBS-ACS-2] 00 19 25 0b 87 00 10 00 00 03 00 00 00 00:12:38.425 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 03 00 00 0b dc 00 7a 25 00 00 00 00:00:00.016 NOP [Reserved subcommand] [OBS-ACS-2] Error 3698 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 10 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 8d 25 0b 9f 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 03 00 00 0b 99 00 92 25 00 00 00 00:00:00.016 NOP [Reserved subcommand] [OBS-ACS-2] 00 dc 25 0b 7a 00 10 00 00 03 00 00 00 00:12:35.481 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 03 00 00 0b 5c 00 6f 25 00 00 00 00:00:00.016 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 25393 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 37/37 Celsius Lifetime Min/Max Temperature: 37/50 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/85 Celsius Temperature History Size (Index): 128 (59) Index Estimated Time Temperature Celsius 60 2020-01-19 14:14 36 ***************** ... ..( 29 skipped). .. ***************** 90 2020-01-19 14:44 36 ***************** 91 2020-01-19 14:45 ? - 92 2020-01-19 14:46 37 ****************** ... ..( 39 skipped). .. ****************** 4 2020-01-19 15:26 37 ****************** 5 2020-01-19 15:27 ? - 6 2020-01-19 15:28 37 ****************** ... ..( 52 skipped). .. ****************** 59 2020-01-19 16:21 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x8000 4 3568 Vendor specific /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST3500418AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC34 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jan 19 16:21:47 2020 CET ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213891en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 93) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 118 099 006 - 193718697 3 Spin_Up_Time PO---- 097 096 000 - 0 4 Start_Stop_Count -O--CK 090 090 020 - 10306 5 Reallocated_Sector_Ct PO--CK 098 098 036 - 96 7 Seek_Error_Rate POSR-- 085 060 030 - 4697352864 9 Power_On_Hours -O--CK 078 078 000 - 19909 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 090 037 020 - 10405 183 Runtime_Bad_Block ------ 012 012 000 - 88 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 098 098 000 - 2 188 Command_Timeout -O--CK 098 094 000 - 128850985678 189 High_Fly_Writes -O-RCK 025 025 000 - 75 190 Airflow_Temperature_Cel -O---K 065 054 045 - 35 (Min/Max 35/36) 194 Temperature_Celsius -O---K 035 046 000 - 35 (0 10 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 028 015 000 - 193718697 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 073 000 - 31342 240 Head_Flying_Hours ------ 100 253 000 - 44856 (82 105 0) 241 Total_LBAs_Written ------ 100 253 000 - 877494066 242 Total_LBAs_Read ------ 100 253 000 - 4001302762 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL,SL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 5373 hours (223 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 5e 00 01 d4 00 00 Error: UNC at LBA = 0x5e0001d4 = 1577058772 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 00 80 00 00 4e 00 00 80 40 00 01:22:09.762 READ DMA EXT 25 00 ff 00 80 00 05 4f 00 43 68 40 00 01:22:09.761 READ DMA EXT 25 00 ff 00 80 00 05 4e 00 43 68 40 00 01:22:09.761 READ DMA EXT 25 00 ff 00 80 00 00 00 00 00 80 40 00 01:22:09.688 READ DMA EXT 25 00 ff 00 80 00 00 00 00 00 00 40 00 01:22:09.677 READ DMA EXT Error 1 [0] occurred at disk power-on lifetime: 5039 hours (209 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 5e 00 01 d4 00 00 Error: UNC at LBA = 0x5e0001d4 = 1577058772 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 00 80 00 00 5e 00 01 80 40 00 01:20:21.510 READ DMA EXT 25 00 ff 00 80 00 00 5e 00 01 00 40 00 01:20:21.510 READ DMA EXT 35 00 ff 00 c0 00 00 99 00 67 78 40 00 01:20:21.509 WRITE DMA EXT 25 00 ff 00 40 00 00 a3 00 3e ca 40 00 01:20:21.501 READ DMA EXT 25 00 ff 00 80 00 00 4c 00 01 00 40 00 01:20:21.486 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 6061 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 35/36 Celsius Lifetime Min/Max Temperature: 10/46 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (82) Index Estimated Time Temperature Celsius 83 2020-01-14 10:56 32 ************* 84 2020-01-14 11:55 32 ************* 85 2020-01-14 12:54 ? - 86 2020-01-14 13:53 17 - 87 2020-01-14 14:52 17 - 88 2020-01-14 15:51 32 ************* ... ..( 2 skipped). .. ************* 91 2020-01-14 18:48 32 ************* 92 2020-01-14 19:47 31 ************ 93 2020-01-14 20:46 ? - 94 2020-01-14 21:45 17 - 95 2020-01-14 22:44 17 - 96 2020-01-14 23:43 31 ************ ... ..( 2 skipped). .. ************ 99 2020-01-15 02:40 31 ************ 100 2020-01-15 03:39 30 *********** 101 2020-01-15 04:38 30 *********** 102 2020-01-15 05:37 30 *********** 103 2020-01-15 06:36 ? - 104 2020-01-15 07:35 15 - 105 2020-01-15 08:34 15 - 106 2020-01-15 09:33 30 *********** 107 2020-01-15 10:32 ? - 108 2020-01-15 11:31 16 - 109 2020-01-15 12:30 16 - 110 2020-01-15 13:29 31 ************ 111 2020-01-15 14:28 32 ************* 112 2020-01-15 15:27 32 ************* 113 2020-01-15 16:26 31 ************ 114 2020-01-15 17:25 31 ************ 115 2020-01-15 18:24 31 ************ 116 2020-01-15 19:23 30 *********** 117 2020-01-15 20:22 30 *********** 118 2020-01-15 21:21 31 ************ 119 2020-01-15 22:20 31 ************ 120 2020-01-15 23:19 31 ************ 121 2020-01-16 00:18 32 ************* 122 2020-01-16 01:17 32 ************* 123 2020-01-16 02:16 33 ************** ... ..( 6 skipped). .. ************** 2 2020-01-16 09:09 33 ************** 3 2020-01-16 10:08 ? - 4 2020-01-16 11:07 18 - 5 2020-01-16 12:06 18 - 6 2020-01-16 13:05 33 ************** 7 2020-01-16 14:04 35 **************** 8 2020-01-16 15:03 34 *************** 9 2020-01-16 16:02 33 ************** 10 2020-01-16 17:01 33 ************** 11 2020-01-16 18:00 33 ************** 12 2020-01-16 18:59 32 ************* ... ..( 2 skipped). .. ************* 15 2020-01-16 21:56 32 ************* 16 2020-01-16 22:55 ? - 17 2020-01-16 23:54 19 - 18 2020-01-17 00:53 19 - 19 2020-01-17 01:52 33 ************** 20 2020-01-17 02:51 35 **************** ... ..( 2 skipped). .. **************** 23 2020-01-17 05:48 35 **************** 24 2020-01-17 06:47 34 *************** 25 2020-01-17 07:46 35 **************** 26 2020-01-17 08:45 34 *************** 27 2020-01-17 09:44 35 **************** 28 2020-01-17 10:43 35 **************** 29 2020-01-17 11:42 35 **************** 30 2020-01-17 12:41 ? - 31 2020-01-17 13:40 17 - 32 2020-01-17 14:39 17 - 33 2020-01-17 15:38 31 ************ 34 2020-01-17 16:37 33 ************** 35 2020-01-17 17:36 33 ************** 36 2020-01-17 18:35 31 ************ 37 2020-01-17 19:34 33 ************** 38 2020-01-17 20:33 34 *************** 39 2020-01-17 21:32 34 *************** 40 2020-01-17 22:31 ? - 41 2020-01-17 23:30 35 **************** 42 2020-01-18 00:29 ? - 43 2020-01-18 01:28 35 **************** 44 2020-01-18 02:27 ? - 45 2020-01-18 03:26 36 ***************** 46 2020-01-18 04:25 ? - 47 2020-01-18 05:24 36 ***************** 48 2020-01-18 06:23 ? - 49 2020-01-18 07:22 36 ***************** 50 2020-01-18 08:21 ? - 51 2020-01-18 09:20 36 ***************** 52 2020-01-18 10:19 36 ***************** 53 2020-01-18 11:18 35 **************** 54 2020-01-18 12:17 34 *************** 55 2020-01-18 13:16 35 **************** 56 2020-01-18 14:15 ? - 57 2020-01-18 15:14 23 **** 58 2020-01-18 16:13 23 **** 59 2020-01-18 17:12 ? - 60 2020-01-18 18:11 22 *** 61 2020-01-18 19:10 22 *** 62 2020-01-18 20:09 33 ************** 63 2020-01-18 21:08 34 *************** 64 2020-01-18 22:07 34 *************** 65 2020-01-18 23:06 33 ************** 66 2020-01-19 00:05 33 ************** 67 2020-01-19 01:04 33 ************** 68 2020-01-19 02:03 32 ************* ... ..( 3 skipped). .. ************* 72 2020-01-19 05:59 32 ************* 73 2020-01-19 06:58 33 ************** 74 2020-01-19 07:57 34 *************** 75 2020-01-19 08:56 34 *************** 76 2020-01-19 09:55 34 *************** 77 2020-01-19 10:54 35 **************** 78 2020-01-19 11:53 ? - 79 2020-01-19 12:52 34 *************** 80 2020-01-19 13:51 ? - 81 2020-01-19 14:50 36 ***************** 82 2020-01-19 15:49 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc === START OF INFORMATION SECTION === Model Family: Western Digital Elements / My Passport (USB) Device Model: WDC WD5000BMVW-11AJGS4 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jan 19 16:21:48 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 129) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 118 110 021 - 5066 4 Start_Stop_Count -O--CK 098 098 000 - 2550 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 092 092 000 - 5993 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 177 192 Power-Off_Retract_Count -O--CK 200 200 000 - 52 193 Load_Cycle_Count -O--CK 198 198 000 - 8515 194 Temperature_Celsius -O---K 116 104 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 21/31 Celsius Lifetime Min/Max Temperature: 17/43 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (70) Index Estimated Time Temperature Celsius 71 2020-01-19 14:14 ? - 72 2020-01-19 14:15 28 ********* 73 2020-01-19 14:16 29 ********** 74 2020-01-19 14:17 ? - 75 2020-01-19 14:18 29 ********** 76 2020-01-19 14:19 ? - 77 2020-01-19 14:20 29 ********** 78 2020-01-19 14:21 29 ********** 79 2020-01-19 14:22 30 *********** ... ..( 4 skipped). .. *********** 84 2020-01-19 14:27 30 *********** 85 2020-01-19 14:28 31 ************ ... ..( 7 skipped). .. ************ 93 2020-01-19 14:36 31 ************ 94 2020-01-19 14:37 ? - 95 2020-01-19 14:38 31 ************ ... ..( 8 skipped). .. ************ 104 2020-01-19 14:47 31 ************ 105 2020-01-19 14:48 ? - 106 2020-01-19 14:49 31 ************ ... ..( 18 skipped). .. ************ 125 2020-01-19 15:08 31 ************ 126 2020-01-19 15:09 ? - 127 2020-01-19 15:10 31 ************ ... ..( 33 skipped). .. ************ 33 2020-01-19 15:44 31 ************ 34 2020-01-19 15:45 ? - 35 2020-01-19 15:46 31 ************ 36 2020-01-19 15:47 ? - 37 2020-01-19 15:48 31 ************ 38 2020-01-19 15:49 ? - 39 2020-01-19 15:50 31 ************ ... ..( 7 skipped). .. ************ 47 2020-01-19 15:58 31 ************ 48 2020-01-19 15:59 ? - 49 2020-01-19 16:00 31 ************ 50 2020-01-19 16:01 31 ************ 51 2020-01-19 16:02 ? - 52 2020-01-19 16:03 31 ************ 53 2020-01-19 16:04 ? - 54 2020-01-19 16:05 31 ************ 55 2020-01-19 16:06 ? - 56 2020-01-19 16:07 31 ************ 57 2020-01-19 16:08 ? - 58 2020-01-19 16:09 31 ************ ... ..( 11 skipped). .. ************ 70 2020-01-19 16:21 31 ************ SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 42 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 43 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 67492 Vendor specific