/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z5K500 Device Model: HGST HTS545050A7E380 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GG2OAC90 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Jan 26 20:29:34 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 113) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 198 198 040 - 129 3 Spin_Up_Time POS--- 214 214 033 - 1 4 Start_Stop_Count -O--C- 099 099 000 - 3018 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 112 112 040 - 35 9 Power_On_Hours -O--C- 091 091 000 - 4071 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 2704 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 099 099 000 - 317 193 Load_Cycle_Count -O--C- 093 093 000 - 76406 194 Temperature_Celsius -O---- 162 162 000 - 37 (Min/Max 17/52) 196 Reallocated_Event_Count -O--CK 100 100 000 - 46 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 325 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 325 [0] occurred at disk power-on lifetime: 1616 hours (67 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 60 00 00 00 3c 56 88 00 00 Error: UNC at LBA = 0x003c5688 = 3954312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 38 00 00 00 3c 59 e8 40 00 00:41:51.413 READ FPDMA QUEUED 60 01 00 00 30 00 00 00 3c 58 e8 40 00 00:41:51.413 READ FPDMA QUEUED 60 01 00 00 28 00 00 00 3c 57 e8 40 00 00:41:51.413 READ FPDMA QUEUED 60 01 00 00 20 00 00 00 3c 56 e8 40 00 00:41:51.413 READ FPDMA QUEUED 60 01 00 00 18 00 00 00 3c 55 e8 40 00 00:41:51.413 READ FPDMA QUEUED Error 324 [3] occurred at disk power-on lifetime: 1616 hours (67 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 60 00 00 00 3c 56 88 00 00 Error: UNC at LBA = 0x003c5688 = 3954312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 38 00 00 00 3c 59 e8 40 00 00:41:07.010 READ FPDMA QUEUED 60 01 00 00 30 00 00 00 3c 58 e8 40 00 00:41:07.010 READ FPDMA QUEUED 60 01 00 00 28 00 00 00 3c 57 e8 40 00 00:41:07.010 READ FPDMA QUEUED 60 01 00 00 20 00 00 00 3c 56 e8 40 00 00:41:07.010 READ FPDMA QUEUED 60 01 00 00 18 00 00 00 3c 55 e8 40 00 00:41:07.010 READ FPDMA QUEUED Error 323 [2] occurred at disk power-on lifetime: 1616 hours (67 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 3c 56 88 00 00 Error: WP at LBA = 0x003c5688 = 3954312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 10 00 00 00 63 14 38 40 00 00:41:03.858 WRITE FPDMA QUEUED 60 00 40 00 08 00 00 00 05 ed 22 40 00 00:41:03.679 READ FPDMA QUEUED 60 00 08 00 00 00 00 00 3c 56 88 40 00 00:41:03.182 READ FPDMA QUEUED 60 00 08 00 00 00 00 00 3c 56 80 40 00 00:41:03.182 READ FPDMA QUEUED 60 00 08 00 00 00 00 00 3c 56 78 40 00 00:41:03.182 READ FPDMA QUEUED Error 322 [1] occurred at disk power-on lifetime: 1616 hours (67 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 58 00 00 00 3c 56 88 00 00 Error: UNC at LBA = 0x003c5688 = 3954312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 40 00 00 00 3c 5a e0 40 00 00:40:59.507 READ FPDMA QUEUED 60 01 00 00 38 00 00 00 3c 59 e0 40 00 00:40:59.507 READ FPDMA QUEUED 60 01 00 00 30 00 00 00 3c 58 e0 40 00 00:40:59.507 READ FPDMA QUEUED 60 01 00 00 28 00 00 00 3c 57 e0 40 00 00:40:59.507 READ FPDMA QUEUED 60 01 00 00 20 00 00 00 3c 56 e0 40 00 00:40:59.507 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 36/38 Celsius Lifetime Min/Max Temperature: 17/52 Celsius Lifetime Average Temperature: 39 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (121) Index Estimated Time Temperature Celsius 122 2018-01-26 18:22 39 ******************** ... ..( 9 skipped). .. ******************** 4 2018-01-26 18:32 39 ******************** 5 2018-01-26 18:33 38 ******************* ... ..( 3 skipped). .. ******************* 9 2018-01-26 18:37 38 ******************* 10 2018-01-26 18:38 39 ******************** 11 2018-01-26 18:39 39 ******************** 12 2018-01-26 18:40 38 ******************* 13 2018-01-26 18:41 38 ******************* 14 2018-01-26 18:42 38 ******************* 15 2018-01-26 18:43 39 ******************** ... ..( 11 skipped). .. ******************** 27 2018-01-26 18:55 39 ******************** 28 2018-01-26 18:56 38 ******************* 29 2018-01-26 18:57 38 ******************* 30 2018-01-26 18:58 38 ******************* 31 2018-01-26 18:59 39 ******************** 32 2018-01-26 19:00 39 ******************** 33 2018-01-26 19:01 39 ******************** 34 2018-01-26 19:02 38 ******************* ... ..( 12 skipped). .. ******************* 47 2018-01-26 19:15 38 ******************* 48 2018-01-26 19:16 37 ****************** ... ..( 15 skipped). .. ****************** 64 2018-01-26 19:32 37 ****************** 65 2018-01-26 19:33 36 ***************** ... ..( 3 skipped). .. ***************** 69 2018-01-26 19:37 36 ***************** 70 2018-01-26 19:38 ? - 71 2018-01-26 19:39 36 ***************** 72 2018-01-26 19:40 37 ****************** ... ..( 9 skipped). .. ****************** 82 2018-01-26 19:50 37 ****************** 83 2018-01-26 19:51 36 ***************** 84 2018-01-26 19:52 37 ****************** 85 2018-01-26 19:53 38 ******************* ... ..( 7 skipped). .. ******************* 93 2018-01-26 20:01 38 ******************* 94 2018-01-26 20:02 37 ****************** ... ..( 5 skipped). .. ****************** 100 2018-01-26 20:08 37 ****************** 101 2018-01-26 20:09 36 ***************** 102 2018-01-26 20:10 36 ***************** 103 2018-01-26 20:11 37 ****************** ... ..( 3 skipped). .. ****************** 107 2018-01-26 20:15 37 ****************** 108 2018-01-26 20:16 38 ******************* 109 2018-01-26 20:17 38 ******************* 110 2018-01-26 20:18 37 ****************** 111 2018-01-26 20:19 37 ****************** 112 2018-01-26 20:20 38 ******************* 113 2018-01-26 20:21 37 ****************** 114 2018-01-26 20:22 38 ******************* 115 2018-01-26 20:23 38 ******************* 116 2018-01-26 20:24 38 ******************* 117 2018-01-26 20:25 37 ****************** 118 2018-01-26 20:26 37 ****************** 119 2018-01-26 20:27 38 ******************* 120 2018-01-26 20:28 38 ******************* 121 2018-01-26 20:29 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 13 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS